User Guide for ALTA models including: 2AU29ALTAWSSV2, 2AU29ALTAWSSV2, altawssv2, BLISS Surface Mounted Wall Switch, BLISS Switch, Surface Mounted Wall Switch, Mounted Wall Switch, Switch
Turnils North America ALTAWSSV2 Wall Switch 2AU29ALTAWSSV2 2AU29ALTAWSSV2 altawssv2
File Info : application/pdf, 4 Pages, 3.27MB
DocumentDocumentCHANNEL OPTIONS SELECT A CHANNEL a. Press "-" button on the wall switch to select a lower channel. b. Press "+" button on the wall switch to select a higher channel. Action on a. Wall Switch Lower Channel Wall Switch Response b. Higher Channel HIDE UNUSED CHANNELS a. Press and Hold (about 3 sec) "-" and "+" buttons simultaneously until wall switch displays "C" (channel). b. Press "-" or "+" button to select required quantity of channel (between 1 to 15). c. Press "Stop" button to conrm selection (the example shows a 5-channel selection). The LED will display "O" (O.) once to conrm selection. Action on a. Wall Switch Wall Switch Response Action on b. Wall Switch Wall Switch Response + Lower Higher Channel Channel or Lower Higher Channel Channel Action on c. Wall Switch Stop Wall Switch Response GETTING STARTED It is important to conm tKat tKe motor is aZaNe and ready to receiYe programming. To do tKis press ùP1ú button on tKe motor less tKan 1 sec to actiYate tKe motor Irom Sleep Mode. 1. PAIR / UNPAIR WALL SWITCH *Honeycomb /Cellular and Horizontal Blind Motors DO NOT BEEP. a. Press "P1" button (about 2 sec) on the motor head until motor jog x1 and beep x1. b. In the next 10 secs, press and hold "Stop" button on the wall switch until motor jog x2 and beep x3. * Repeat the same procedure to unpair wall switch. Action on Motor Motor Response a. P1 Action on b. Wall Switch Motor Response P1 Jog x1 Stop Jog x2 P1 Beep x1 Beep x3 2. CHANGE MOTOR DIRECTION (IF NECESSARY) Press "Up" or "Down" button to check if the shade moves in the desired direction. Action on Wall Switch If you need to reverse the direction, press and hold (about 2 sec) "Up" Motor and "Down" buttons simultaneously until motor jog x1 and beep x1. Response + Up Down Jog x1 Beep x1 *The operation is only valid when there are no limits. If the motor has already set the upper and lower limit, then you can only switch direction by pressing "P1" button (about 10 sec) on the motor head until motor jog x3 and beep x3. 3. SETTING THE UPPER AND LOWER LIMITS SET UPPER LIMIT Action on a. a. Press "Up" button to raise the Wall Switch shade, then press "Stop" button Up when it is in the desired upper limit. b. Press and hold (about 5 sec) "Up" Motor and "Stop" buttons simultaneously Response until motor jog x2 and beep x3. b. Up + Stop Jog x2 Beep x3 SET LOWER LIMIT Action on a. a. Press "Down" button to lower Wall Switch the shade, then press "Stop" button when it is in the desired lower limit. b. Press and hold (about 5 sec) "Down" and "Stop" buttons simultaneously until motor jog x2 and beep x3. Motor Response *If you exit the limit setting status before you nish the limit settings, the motor will take the previous existing limits. Down b. + Down Stop Jog x2 Beep x3 Factory Mode Complete User Mode Begins 4. ADJUST LIMITS ADJUST THE UPPER LIMIT Action on a. Wall Switch a. Press and hold (about 5 sec) "Up" Up + Stop and "Stop" buttons simultaneously until motor jog x1 and beep x1. Motor Jog x1 Beep b. Use "Up" button to raise the Response x1 shade to the desired highest position, and use "Up" or "Down" button to do the nal adjustment iI necessary. Action on c. Wall Switch Up + Stop c. Press and hold (about 5 sec) "Up" Motor and "Stop" buttons simultaneously until motor jog x2 and beep x3. Response Jog x2 Beep x3 b. Up ADJUST THE LOWER LIMIT a. Press and hold (about 5 sec) "Down" and "Stop" buttons simultaneously until motor jog x1 and beep x1. b. Use "Down" button to lower the shade to the desired lowest position, and use "Up" or "Down" button to do the nal adjustment if necessary. c. Press and hold (about 5 sec) "Down" and "Stop" buttons simultaneously until motor jogs x2 and beeps x3. Action on Wall Switch Motor Response Action on Wall Switch Motor Response 5. FAVORITE POSITION SET FAVORITE POSITION a. Use "Up" or "Down" button to move the shade to desired Favorite position. b. Press and hold (about 2 sec) one "P2" button on the back of wall switch until motor jog x1 and beep x1. c. Press and hold (about 2 sec) "Stop" button until motor jog x1 and beep x1. d. Once more, press and hold (about 2 sec) "Stop" button until motor jog x2 and beep x3. Action on Wall Switch Motor Response Action on Wall Switch Motor Response a. + Down Stop b. Down Jog x1 Beep x1 c. + Down Stop Jog x2 Beep x3 a. Up or b. P2 Buttons Down or c. Stop Jog x1 Beep x1 Jog x1 Beep x1 d. Stop Jog x2 Beep x3 SEND SHADE TO FAVORITE Action on POSITION Wall Switch Stop Press and hold (about 2 sec) "Stop" button, motor will move to Favorite position. Shade Response or DELETE FAVORITE POSITION a. Press and hold (about 2 sec) one "P2" button until motor jog and beep x1. b. Press and hold (about 2 sec) "Stop" button until motor jog and beep x1. c. Once more, press and hold (about 2 sec) "Stop" button until motor jog x1 and long beep x1. Action on a. Wall Switch Motor Response Action on c. Wall Switch Motor Response P2 Buttons b. Jog x1 Beep x1 Stop Jog x1 Beep x1 Stop Jog x1 Beep x1 6. ROLLER MODE AND SHEER MODE ROLLER SHADE MODE DeIault mode allows Ior continuous raising/lowering oI shade aIter a short press. a. Press and hold (about 5 sec) "Up" and "Down" buttons simultaneously until motor jog x1. b. Press and hold (about 2 sec) "Stop" button until motor jog x2 and beep x3. Action on a. Wall Switch Motor Response Action on b. Wall Switch Motor Response + Up Down Jog x1 Stop Jog x2 Beep x3 SHEER SHADE MODE - Allows Ior slight adMustment aIter a short press and raising/ lowering oI shade aIter a longer press. a. Press and hold (about 5 sec) "Up" and "Down" buttons simultaneously until motor jog x1. b. Press and hold (about 2 sec) "Stop" button until motor jog x1 and beep x1. Action on Wall Switch a. Up + Down Motor Response Jog x1 Action on b. Wall Switch Motor Response Stop Jog x1 Beep x1 7. ADD OR REMOVE ADDITIONAL WALL SWITCH USING CURRENT WALL SWITCH a. On the current wall switch, press and hold (about 2 sec) one "P2" button until motor jog x1 and beep x1. b. Once more, on the current wall switch, press and hold (about 2 sec) one "P2" button until motor jog x1 and beep x1. c. On the New wall switch, press and hold (about 2 sec) one "P2" button until motor jog x2 and beep x3. *Repeat the same procedure to remove additional wall switch. Action on Wall Switch a. Current Wall Switch P2 Buttons Motor Response Action on Wall Switch Jog x1 Beep x1 c. New Wall Switch P2 Buttons Motor Response Jog x2 Beep x3 b. Current Wall Switch P2 Buttons Jog x1 Beep x1 NEW WALL SWITCH CONTROL Follow instructions under the section 1. Pair / Unpair Wall Switch 8. ADJUST MOTOR SPEED INCREASE MOTOR SPEED Action on a. P2 Buttons b. Wall Switch a. Press one "P2" button until motor jog x1 and beep x1. b. Press "Up" button until motor jog x1 and beep x1. Motor c. Once more, press "Up" button until motor jog x2 and beep x1. Response Action on c. Wall Switch Jog x1 Beep x1 Up Up Jog x1 Beep x1 Motor Response Jog x2 Beep x1 DECREASE MOTOR SPEED a. Press one "P2" button until motor jog x1 and beep x1. Action on Wall Switch a. P2 Buttons b. Down b. Press "Down" button until motor jog x1 and beep x1. Motor c. Once more, press "Down" button Response until motor jog x2 and beep x1. Action on c. Wall Switch Jog x1 Beep x1 Down Jog x1 Beep x1 *If the motor has no response, it already has a Maximum or Minimum speed. Motor Response Jog x2 Beep x1 OPTIONS DE CANAL SÉLECTIONNER UN CANAL a. Appuyez le bouton « - » sur l'interrupteur mural pour sélectionnez un canal plus bas. b. Appuyez le bouton « + » sur l'interrupteur mural pour sélectionnez un canal plus haut. Action sur a. l'interrupteur mural Réponse de l'interrupteur mural Canal plus bas b. Canal plus haut CACHER LES CANAUX NONUTILISÉS a. Appuyez et maintenez (environ 3s) les boutons « - » et « + » simultanément jusqu'à ce que l'interrupteur mural montre « C » (canal). b. Appuyez le bouton « - » ou « + » pour sélectionnez la quantité de canaux requise (entre 1 et 15). c. Appuyez le bouton « Arrêt » pour conrmer la sélection (l'exemple montre une sélection de 5 canaux). La lumière LED montrera « O » (OK) pour conrmer la sélection. Action sur a. l'interrupteur mural Réponse de l'interrupteur mural Action sur b. l'interrupteur mural Réponse de l'interrupteur mural + Canal Canal plus bas plus haut ou Canal Canal plus bas plus haut Action sur c. l'interrupteur mural Arrêt Réponse de l'interrupteur mural POUR COMMENCER C'est important de conrmer Tue le moteur est réveillé et pr¬t pour la programmation. Pour Iaire cela appuyez le bouton « P1 » sur le moteur pendant moins de 1 seconde pour activer le moteur du mode veille. 1. COUPLER / DÉCOUPELR L'INTERRUPTEUR MURAL *Les moteurs pour alvéolés/cel- Action sur le a. P1 P1 lulaires et pour stores horizontaux moteur N'ÉMETTENT PAS DES BIPS. P1 a. Appuyez le bouton « P1 » (environ 2s) sur la tête du moteur jusqu'à ce que le moteur secoue x1 Réponse du moteur Secoue x1 Bip x1 et bip x1. b. Dans les prochaines 10 secondes, appuyez et maintenez le bouton « Arrêt » sur l'interrupteur mural jusqu'à ce que le moteur secoue x2 et bip x3. Action sur b. l'interrupteur mural Réponse du Arrêt Secoue x2 Bip x3 *Répétez la même procédure pour découpler un interrupteur mural. moteur 2. CHANGER LA DIRECTION DU MOTEUR (SI NÉCESSAIRE) Appuyez le bouton « Haut » ou « Bas » pour vérier si le store bouge dans la direction désirée. Si vous devez inverser la direction, appuyez et maintenez (environ 2s) les boutons « Haut » et « Bas » simultanément jusqu'à ce que le moteur secoue x1 et bip x1. Action sur l'interrupteur mural Réponse du moteur + Haut Bas Secoue x1 Bip x1 *Le fonctionnement est seulement valide lorsqu'il n'y a pas de limites. Si le moteur a déjà une limite supérieure et inférieure, vous pouvez seulement changer de direction en appuyant le bouton P1 (environ 10s) sur la tête du moteur jusqu'à ce que le moteur secoue x3 et bip x3. 3. RÉGLER LES LIMITES SUPÉRIEURES ET INFÉRIEURES RÉGLER LA LIMITE SUPÉRIEURE a. Appuyez le bouton « Haut » pour soulever le store, ensuite appuyez le bouton « Arrêt » lorsque le store est dans la limite supérieure désirée. b. Appuyez et maintenez (environ 5s) les boutons « Haut » et « Arrêt » simultanément jusqu'à ce que le moteur secoue x2 et bip x3. Action sur a. l'interrupteur mural Réponse du moteur Haut b. Haut + Arrêt Secoue x2 Bip x3 RÉGLER LA LIMITE INFÉRIEURE Action sur a. a. Appuyez le bouton « Bas » pour abaisser le store, ensuite appuyez le l'interrupteur mural bouton « Arrêt » lorsque le store est dans la limite inférieure désirée. Réponse du b. Appuyez et maintenez (environ 5s) les boutons « Bas» et « Arrêt » simultanément jusqu'à ce que le moteur secoue x2 et bip x3. moteur *Si vous sortez du réglage des limites avant que vous terminer le réglage, le moteur prendra les limites existantes précédentes. b. + Bas Bas Arrêt Secoue x2 Bip x3 Mode de l'usine complète Mode de l'utilisateur commence 4. AJUSTER LES LIMITES AJUSTER LA LIMITE SUPÉRIEURE a. Appuyez et maintenez (environ 5s) les boutons « Haut » et « Arrêt » simultanément jusqu'à ce que le moteur secoue x1 et bip x1. b. Utilisez le bouton « Haut » pour soulever le store à la position la plus haute désirée, et utilisez les boutons « Haut » ou « Bas » pour faire un ajustement nal si nécessaire. c. Appuyez et maintenez (environ 5s) les boutons « Haut » et « Arrêt » simultanément jusqu'à ce que le moteur secoue x2 et bip x3. Action sur a. l'interrupteur mural Réponse du moteur Action sur c. l'interrupteur mural Réponse du moteur + Haut Secoue x1 + Haut Secoue x2 Arrêt Bip x1 Arrêt Bip x3 b. Haut AJUSTER LA LIMITE INFÉRIEURE a. Appuyez et maintenez (environ 5s) les boutons « Bas » et « Arrêt » simultanément jusqu'à ce que le moteur secoue x1 et bip x1. b. Utilisez le bouton « Bas » pour abaisser le store à la position la plus basse désirée, et utilisez les boutons « Haut » ou « Bas » pour faire un ajustement nal si nécessaire. c. Appuyez et maintenez (environ 5s) les boutons « Bas » et « Arrêt » simultanément jusqu'à ce que le moteur secoue x2 et bip x3. Action sur a. l'interrupteur mural Réponse du moteur Action sur c. l'interrupteur mural Réponse du moteur + Bas Secoue x1 + Bas Secoue x2 Arrêt Bip x1 Arrêt Bip x3 b. Bas 5. POSITION PRÉFÉRÉE RÉGLER LA POSITION PRÉFÉRÉE a. Utilisez le bouton « Haut » ou « Bas » pour placer le store dans la position préférée désirée. Action sur a. l'interrupteur mural Haut ou Bas b. Bouton P2 b. Appuyez et maintenez (environ 2s) un bouton « P2 » à l'arrière de l'interrupteur jusqu'à ce que le moteur secoue x1 et bip x1. Réponse du moteur ou Secoue x1 Bip x1 c. Appuyez et maintenez (environ 2s) le bouton « Arrêt » jusqu'à ce que le moteur secoue x1 et bip x1. d. Une dernière fois, appuyez et maintenez (environ 2s) le bouton « Arrêt » jusqu'à ce que le moteur secoue x2 et bip x3. Action sur c. l'interrupteur mural Réponse du moteur Arrêt Secoue x1 Bip x1 d. Arrêt Secoue x2 Bip x3 ENVOYER LE STORE À LA POSITION PRÉFÉRÉE Appuyez et maintenez (environ 2s) le bouton « Arrêt », le moteur se déplacera à la position préférée. Action sur l'interrupteur mural Réponse du store Arrêt ou SUPPRIMER LA POSITION PRÉFÉRÉE a. Appuyez et maintenez (environ 2s) un bouton « P2 » jusqu'à ce que le moteur secoue et bip x1. b. Appuyez et maintenez (environ 2s) le bouton « Arrêt » jusqu'à ce que le moteur secoue et bip x1. c. Une dernière fois, appuyez et maintenez (environ 2s) le bouton « Arrêt » jusqu'à ce que le moteur secoue x1 et fait un long bip x1. Action sur a. l'interrupteur mural Réponse du moteur Action sur c. l'interrupteur mural Réponse du moteur Bouton P2 b. Secoue x1 Bip x1 Arrêt Secoue x1 Bip x1 Arrêt Secoue x1 Bip x1 6. MODE ENROULEUR OU TRANSLUCIDE MODE DE STORE À ENROULEUR ô Mode de déIaut permet un mouvement continue de soulèvement/abaissement après une pression courte a. Appuyez et maintenez (environ 5s) les boutons « Haut » et « Bas » simultanément jusqu'à ce que le moteur secoue x1. b. Appuyez et maintenez (environ 2s) le bouton « Arrêt » jusqu'à ce que le moteur secoue x2 et bip x3. Action sur a. + l'interrupteur Haut Bas mural Réponse du Secoue x1 moteur Action sur b. l'interrupteur mural Arrêt Réponse du moteur Secoue x2 Bip x3 MODE DE STORE TRANSLUCIDE Permet à un ajustement précis après une pression courte et soulève/abaisse le store après une pression longue a. Appuyez et maintenez (environ 5s) les boutons « Haut » et « Bas » simultanément jusqu'à ce que le moteur secoue x1. b. Appuyez et maintenez (environ 2s) le bouton « Arrêt » jusqu'à ce que le moteur secoue x1 et bip x1. Action sur l'interrupteur mural Réponse du moteur Action sur l'interrupteur mural Réponse du moteur a. + Haut Bas Secoue x1 b. Arrêt Secoue x1 Bip x1 7. AJOUTER OU SUPPRIMER DES INTERRUPTEURS UTILISER L'INTERRUPTEUR MURAL ACTUEL a. Sur l'interrupteur mural actuel, appuyez et maintenez (environ 2s) les boutons « P2 » jusqu'à ce que le moteur secoue x1 et bip x1. b. Une autre fois, sur l'interrupteur actuel, appuyez et maintenez (environ 2s) les boutons « P2 » jusqu'à ce que le moteur secoue x1 et bip x1 c. Sur le nouveau interrupteur, appuyez et maintenez (environ 2s) les boutons « P2 » jusqu'à ce que le moteur secoue x2 et bip x3. Action sur a. Interrupteur mural actuel l'interrupteur Bouton P2 mural Interrupteur mural b. actuel Bouton P2 Réponse du moteur Secoue x1 Bip x1 Action sur l'interrupteur mural c. Nouveau interrupteur Bouton P2 mural Secoue x1 Bip x1 * Répétez la même procédure pour enlever un interrupteur supplémentaire. Réponse du moteur Secoue x2 Bip x3 PROGRAMMER UN NOUVEAU INTERRUPTEUR MURAL Suivez les instructions sous la section 1. Coupler/découpler une télécommande. 8. AJUSTER LA VITESSE DU MOTEUR AUGMENTER LA VITESSE DU MOTEUR a. Appuyez un bouton « P2 » jusqu'à ce que le moteur secoue x1 et bip x1. Action sur a. l'interrupteur mural Bouton P2 b. Appuyez le bouton « Haut » jusqu'à ce que le moteur secoue x1 et bip x1. c. Une dernière fois, appuyez le bouton « Haut » jusqu'à ce que le moteur secoue x2 et bip x1. Réponse du moteur Action sur c. l'interrupteur mural Secoue x1 Bip x1 Haut Réponse du moteur Secoue x2 Bip x1 b. Haut Secoue x1 Bip x1 DIMINUER LA VITESSE DU MOTEUR a. Appuyez un bouton « P2 » jusqu'à ce que le moteur secoue x1 et bip x1. b. Appuyez le bouton « Bas » jusqu'à ce que le moteur secoue x1 et bip x1. c. Une dernière fois, appuyez le bouton « Bas » jusqu'à ce que le moteur secoue x2 et bip x1. *Si le moteur n'a aucune réponse, il a déjà la vitesse maximum ou minimum. Action sur a. l'interrupteur mural Bouton P2 Réponse du moteur Action sur c. l'interrupteur mural Réponse du moteur Secoue x1 BIp x1 Bas Secoue x2 Bip x1 b. Bas Secoue x1 BIp x1Acrobat Distiller 11.0 (Windows)