INSTRUCTIONS FOR USE ENGLISH

6.10.1 Connecting the Vaporizer with a Smartphone

• Switch on the smartphone and ensure that the Bluetooth® function is switched on and that it is not blocked by another Bluetooth® device. Then switch on the Vaporizer and open a browser which supports Bluetooth® connectivity (more information on www.storz-bickel.com/app/web).

• Go to app.storz-bickel.com.

• Click "Connect" and choose your Vaporizer.

6.10.2 The Menu Items of the STORZ & BICKEL Web App

Temperature: Temperatures can be set on the device itself as well as through the STORZ & BICKEL Web App. Temperatures can be set between 40°C-210°C (104°F-410°F) in the same way as on the interface of the device, see Chapter 6.4.4. Adjusting temperatures.

Fahrenheit/Celsius: Click on the temperature to change from degree Celsius to degree Fahrenheit and vice versa.

Device: Device-related information, such as operating hours, software versions etc. can be found in this section. To find out which additional device specific features can be adjusted through the STORZ & BICKEL Web App, visit: https://www.storz-bickel.com/app/web

7.1.1 Disassembling the Cooling Unit

• Make sure that the Cooling Unit is screwed onto the Vaporizer.

• Pull the Mouthpiece out of the Cooling Unit Cap while slightly tilting it back and forth.

• Pull off the Mouthpiece Seal Ring using the recess.

• Put the edge of the Mouthpiece into the notch at the Rotary Cap and turn it counterclockwise to open and pull out.

• Pull off the Seal Ring from the Rotary Cap using the recess.

• Pull the Cooling Unit Cap off the Vaporizer

• Pull out the Screen inside the Cooling Unit.

• Use the Filling Chamber Tool to press the Setting Wheel out of the Cooling Unit and let the Seal Ring fall out.

• Unscrew the Cooling Unit Base from the Vaporizer by turning it 90° counterclockwise.

• Carefully press out the Screen from above using a cotton swab.

• Lever out the large Base Seal Ring with the Filling Chamber Tool at the recess in the groove.

7.1.2 Cleaning the Cooling Unit and the Filling Chamber Screen

• Use the Cleaning Brush and cotton swabs and paper or cotton cloths for manual cleaning.

• Use warm rinsing water or isopropyl alcohol as a solvent.

• Clean the Filling Chamber Screen and the Screen of the Cooling Unit with the Cleaning Brush after each use.

7.1.3 Check the Cooling Unit Parts and the Filling Chamber Screen

• Check all parts for damaged surfaces, cracks, softening, hardening, embrittlement, contamination or discoloration.

• Discard damaged parts.

7.1.4 Assembling the Cooling Unit

• Assemble the parts in reverse order.

• Place the Seal Ring just on top of the Setting Wheel for Airflow and make sure that the "TOP" label is inserted upwards.

• When assembling, make sure that Seal Rings are properly seated.

• Insert Screen in the groove provided for this purpose.

7.2 Filling Chamber

7.3 Cleaning the Vaporizer and the USB-C cable

• Switch off the Vaporizer

• Disconnect the Vaporizer and the USB-C cable from the mains supply

• Clean the housing of the Vaporizer and the USB-C cable only with a dry soft or damp cloth.

8.1 List of optional accessories

• Wear & Tear Set - SKU 11 64: The Wear & Tear Set contains three Mouthpieces, one Cooling Unit, one Screen Set, two Filling Chamber Tools and a Cleaning Brush.

• Coolings Units, 3 pieces - SKU 11 63 / Cooling Unit - SKU 11 62: The Cooling Unit cools down the vapor and thus provides a pleasant temperature and an optimal aroma. To ensure cleanliness of the Cooling Unit, it should be replaced regularly.

• Mouthpieces, 4 pieces - SKU 11 71: The Set includes four Mouthpieces for the Cooling Unit.

• Screen Set, small - SKU 11 94: Our Screen Set includes all the necessary spare screens for your Vaporizer. Clogged screens might impair airflow and taste, which is why they should be regularly replaced.

• Coarse Screens, 6 pieces - SKU 11 40: The Set includes six coarse mesh Screens.

• Normal Screens, 6 pieces - SKU 11 03: The Set includes six normal mesh Screens.

• Seal Ring Set - SKU 11 82: The Set contains all the sealing rings for the Cooling Unit and Filling Chamber.

• Herb Mill - SKU 11 84 / Herb Mill XL - SKU 09 43: The Herb Mill has extra sharp cutting teeth for finely ground plant material.

• Filling Chamber Tools, 5 pieces - SKU 11 59: The various application options of the Filling Chamber Tool are described in these Instructions for Use.

• Dosing Capsules, 40 pieces - SKU 09 33: Crushed plant material can be filled into the Dosing Capsules. Dispose of the Dosing Capsule after use in household waste.

• Dosing Capsule Magazine - SKU 09 32: Store the filled Dosing Capsules in the Magazine. The Magazine Cap serves as a filling aid for the Dosing Capsules.

• Dosing Capsule Filling Set - SKU 09 45: The Filling Set is designed for the simultaneous filling 40 Dosing Capsules with ground plant material.

• Cleaning Brushes, 3 pieces - SKU 11 24: The Cleaning Brush is used to clean the Filling Chamber, among other things.

• USB-C Supercharger - SKU 11 47: Thanks to the four interchangeable plugs the USB-C Supercharger can be used almost anywhere in the world. The USB-C Supercharger enables fast charging of the device.

You can find these and other accessories as well as detailed information about these products at https://www.storz-bickel.com

9.1 Possible Faults / Troubleshooting

10.1 Vaporizer

• Supply voltage: 5 VDC USB / 5-15 VDC USB-C PD

• Power consumption: 130 W max.

• Operating temperature: 5 °C - 35 °C (41 °F - 95 °F)

• Temperature range: 40 °C - 210 °C (104 °F - 410 °F)

• Size: 15,7 x 5,5 x 3,7 cm (6.18 x 2.17 x 1.46 inch)

• Weight: approx. 252 g (0.56 lbs)

• Frequency band: 2.4-GHz-ISM-Band (2400 to 2483.5 MHz)

• Maximum transmitting power: +5.3 dBm EIRP

• Patents and designs: www.storz-bickel.com/patents

• Subject to technical changes.

10.2 Technical Requirements for suitable Chargers

• For general charging, a USB charger with at least 5 VDC / 2 A (10 W) is recommended.

• Technical requirements for supercharging:

• Charger must support USB-C PD and supply at least 9 VDC / 3 A (27 W).

11.1 Simplified EU Declaration of Conformity

We, STORZ & BICKEL GmbH, hereby declare under our sole responsibility that the VENTY is in conformity with the regulations 2014/30/EU, 2014/53/EU and 2011/65/EU.

The full text of the EU Declaration of Conformity can be obtained at the following internet address: https://www.storz-bickel.com/downloads

12.1 Warranty

S&B Products purchased through the S&B.com directly or an authorized dealer come with a two (2) year limited warranty from the date of purchase by the original purchaser. For customers located in California who purchase on S&B.com, the S&B Limited Warranty starts from the date of delivery to the original purchaser.

Other than for the MIGHTY, CRAFTY+ and PLENTY, if a customer registers the purchased S&B Product at www.storz-bickel.com/registration within four weeks of the purchase date, S&B will grant an additional year of warranty.

S&B only warrants the MIGHTY+, CRAFTY+, VOLCANO HYBRID, VOLCANO CLASSIC, PLENTY, VENTY and MIGHTY (“S&B Products”) against defects in materials and workmanship under Normal Use (as defined below) for 2 years from date of retail purchase directly from S&B.com (or from the date of delivery for customers located in California), or purchase from an authorized retailer (please consult our website).

This Limited Warranty does not cover the commercial use of the product, damage due to misuse, improper maintenance or storage, normal wear and tear, refurbished products or unauthorized repairs of the product.

Furthermore, the Limited Warranty will not cover any other products other than the S&B Products and will not cover any accessories or attachments or components, including but not limited to Batteries, Balloons, Cooling Units, Charging Cables and Adapters, Filling Chamber (VOLCANO), Tube, Screens, Dosing Capsule and accessories included with such S&B Products.

This Limited Warranty is subject to the laws of the Federal Republic of Germany, excluding the UN Convention on Contracts for the International Sale of Goods (CISG). Please find all warranty conditions here: www.storz-bickel.com/legal/warranty.

12.2 Liability

We are liable pursuant to the provisions of the German Product Liability Act as well as in cases of failure or impossibility that we are responsible for. In addition, in the case of a specifically expressed guarantee, we shall be liable for intentional and grossly negligent violations of duty and any injuries to life, body or health that we are responsible for. For property damages and financial loss due to ordinary negligence, we shall be responsible only in the event of violation of material contractual obligations (so-called cardinal obligations), i.e. an obligation, fulfillment of which allows contract performance in the first place and compliance with which the customer normally relies on and may rely on, however, limited to the foreseeable damage typical for the contract. In any other case, our liability is excluded.

The extent that our liability is excluded or restricted also applies to the personal liability of our employees, legal representatives and vicarious agents.

12.3 Copyright

This document is copyright protected, and may not be used either in whole or in part pursuant to Sections 15 et seqq. UrhG (German Copyright Act) without prior written approval of STORZ & BICKEL.