Blizzard InfiniPix Cyclone
User Manual
Table of Contents
1. Getting Started
What's In The Box?
- InfiniPix™ Cyclone Fixture
- Power Cable
- User Manual
Getting It Out Of the Box
Congratulations on purchasing the InfiniPix™ Cyclone. Carefully unpack the box and check the contents to ensure all parts are present and in good condition. If any item appears damaged in transit, notify the shipper immediately and keep the packing material for inspection. Save the original carton and all packing materials, as they are important if the fixture needs to be returned to the factory.
Powering Up!
All fixtures must be powered directly off a switched circuit. They cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100% switch. Warning: All fixtures must be connected to circuits with a suitable Ground (Earthing).
Getting A Hold Of Us
If you encounter any issues, visit blizzardpro.com/support and open a support ticket. Blizzard Lighting is ready to assist.
Disclaimer: Information in this document is subject to change without notice. Blizzard Lighting™ assumes no responsibility or liability for errors or omissions. The latest version of this document can be downloaded from www.blizzardpro.com.
Safety Instructions
⚠ Please read these instructions carefully. They include important information about the installation, usage, and maintenance of this product.
- Keep this User Guide for future use. If selling the unit, ensure the new owner receives this guide.
- Always ensure connection to the proper voltage, and that the line voltage does not exceed the rating on the fixture's decal or rear panel.
- This product is intended for indoor use only.
- To prevent risk of fire or shock, do not expose the fixture to rain or moisture.
- Ensure no flammable materials are close to the unit during operation.
- Install the unit in a location with adequate ventilation, at least 20 inches (50cm) from adjacent surfaces. Ensure no ventilation slots are blocked.
- Always disconnect from the power source before servicing or replacing the fuse. Use the same fuse size and type.
- Always secure the fixture using a safety chain. Never carry the fixture by its head; use its carrying handles.
- Do not operate at ambient temperatures higher than 104°F (40°C).
- In case of a serious operating problem, stop using the unit immediately. Never attempt to repair the unit yourself. Contact an authorized technical assistance center for repairs and use only identical spare parts.
- Never connect the device to a dimmer pack.
- Ensure the power cord is never crimped or damaged.
- Never disconnect the power cord by pulling or tugging on the cord.
- Avoid direct eye exposure to the light source while it is on.
Caution! There are no user-serviceable parts inside. Do not open the housing or attempt repairs. For service, open a support ticket at www.blizzardpro.com/support.
2. Meet the InfiniPix™ Cyclone
Main Features
- 325 x 0.2W RGB 5050 SMD LEDs, rated for 50,000 hours.
- 85 effects patterns + 20 background colors.
- Precise 256-step LED dimming.
- Flicker-free, constant current LED driver.
- 120° beam angle.
- +5V USB port for powering SoC-It™ wireless DMX (sold separately).
- 1-25Hz strobe, pulse, and random effects.
- Equipped with RDM (remote device management).
- Durable composite housing.
- Easy-to-use 4-button LED control panel.
- powerCON-compatible power in/out connections.
- 3-pin DMX in/out connections.
Control
- Protocol: USITT DMX-512, RDM.
- DMX channels: 4/5/8-channels.
- Easy-to-use 4-button control panel with LED display.
- Operating modes: DMX-512, M/S (Master/Slave), Auto, and Sound Active.
DMX Values In-Depth (4/5/8-Channel Modes)
| 4CH | 5CH | 8CH | Value | What it does |
|---|---|---|---|---|
| 1 | 1 | 1 | 000 - 255 | Dimmer (0% - 100%) |
| -- | 2 | 2 | 000 - 030 | Strobe: Open |
| 031 - 090 | Variable strobe (slow <-> fast) | |||
| 091 - 105 | Open | |||
| 106 - 165 | Pulse effect (slow <-> fast) | |||
| 166 - 180 | Open | |||
| 181 - 240 | Random strobe (slow <-> fast) | |||
| 241 - 255 | Open | |||
| 2 | 3 | 3 | 000 - 255 | Red Intensity (0% <-> 100%) |
| 3 | 4 | 4 | 000 - 255 | Green Intensity (0% <-> 100%) |
| 4 | 5 | 5 | 000 - 255 | Blue Intensity (0% <-> 100%) |
| -- | -- | 6 | -- | Pattern Effects |
| 7 | -- | Color Macros | ||
| 8 | -- | Effect Speed |
InfiniPix™ Cyclone Pin-Up Picture
The fixture is a circular lighting unit with a durable composite housing. It features a dense array of 325 x 0.2W RGB 5050 SMD LEDs arranged in concentric circles, creating dynamic visual patterns. It includes a mounting bracket and locking knobs for adjustment.
The Rear Connections
The rear panel of the fixture provides access to essential ports and controls:
- +5V USB: For powering accessories like wireless DMX receivers.
- Power Out: Allows power to be passed to another fixture.
- Power In: Connects to the power source.
- Cooling Vent: Ensures proper airflow for heat dissipation.
- Menu: Button to navigate the control panel.
- DMX In: XLR connector for receiving DMX control signals.
- DMX Out: XLR connector for sending DMX control signals to other fixtures.
- Fuse: Housing for the main power fuse.
3. Setup
⚠ Before replacing the fuse, disconnect the power cord. ALWAYS replace it with the same type and rating.
Fuse Replacement
Remove the fuse holder from its housing. Take out the damaged fuse and replace it with an identical type and rating. Reattach the fuse holder and reconnect power.
Connecting A Bunch of InfiniPix™ Cyclone Fixtures
To run light shows using a DMX-512 controller or to synchronize multiple fixtures in master/slave mode, a serial data link is required. The total number of DMX channels needed by all fixtures on the link determines the maximum number of fixtures the link can support. Fixtures must be daisy-chained in a single line. Connecting more than 32 fixtures without a DMX optically-isolated splitter may degrade the DMX signal. The maximum recommended cable-run distance is 500 meters (1640 ft).
Data/DMX Cabling
Use data-grade cables for linking fixtures to ensure a high-quality signal and reduce electromagnetic interference. Belden® 9841 is recommended for EIA RS-485 applications. Standard microphone cables may work but are less reliable over long distances. Recommended cable characteristics include:
- 2-conductor twisted pair plus a shield.
- Maximum capacitance between conductors: 30 pF/ft.
- Maximum capacitance between conductor & shield: 55 pF/ft.
- Maximum resistance: 20 ohms / 1000 ft.
- Nominal impedance: 100 – 140 ohms.
Cable Connectors
Cables require a male XLR connector on one end and a female XLR connector on the other.
A Word on Termination: DMX is resilient but prone to signal errors. A terminator reduces these errors. If experiencing erratic behavior, especially over long runs, a terminator can help.
To build your own DMX Terminator: Obtain a 120-ohm, 1/4-watt resistor and wire it between pins 2 & 3 of the last fixture. Terminators are also available from specialty retailers.
CAUTION: Do not allow contact between the common (pin 1) and the fixture's chassis ground. This can cause a ground loop and erratic performance. Test cables with an ohm meter to verify correct polarity and ensure pins are not grounded or shorted.
3-Pin??? 5-Pin??? Huh?!?
If your controller uses a 5-pin DMX output, you will need a 5-pin to 3-pin adapter. Here is a proper cable conversion chart:
| Conductor | 3-Pin Female (Output) | 5-Pin Male (Input) |
|---|---|---|
| Ground/Shield | Pin 1 | Pin 1 |
| Data 1- (Primary Data Link) | Pin 2 | Pin 2 |
| Data 1+ (Primary Data Link) | Pin 3 | Pin 3 |
| Data 2- (Optional Secondary Data Link) | -- | Pin 4 - Do Not Use |
| Data 2+ (Optional Secondary Data Link) | -- | Pin 5 - Do Not Use |
Take It To The Next Level: Setting Up DMX Control
- Connect the male connector of the DMX cable to the female connector (output) on the controller.
- Connect the female connector of the DMX cable to the first fixture's male connector (input). Note: The order of fixture connection does not depend on address number; connect based on proximity to the controller.
- Connect subsequent fixtures in the chain from output to input. Place a DMX terminator on the output of the final fixture to ensure best communication.
Diagram Description: Shows DMX IN and DMX OUT ports on fixtures, illustrating a daisy-chain connection with a first fixture and the next fixture in the chain.
Fixture Linking (M/S Mode)
- Connect the male connector side of the DMX cable to the output female connector of the first fixture.
- Connect the cable from the first fixture's female connector to the next fixture's male connector (input). Continue this process for all fixtures.
A quick note: For Master-Slave and Standalone operation, the first fixture often needs to be initialized as a master via control panel settings or DIP-switches. Subsequent fixtures may need to be set as slaves. Refer to the "Operating Adjustments" section for detailed configuration.
Diagram Description: Illustrates DMX IN and DMX OUT connections for linking fixtures in a chain, showing the first fixture and the next fixture.
Mounting & Rigging
Mount the fixture in any SAFE position that allows adequate ventilation. Ensure fan or vent pathways are never obstructed.
IMPORTANT: Always secure your fixture with a safety cable, regardless of the rigging option chosen.
Mount the fixture using a suitable "C" or "O" type clamp. The clamp must be rated to hold at least 10x the fixture's weight for structural stability. Do not mount to surfaces of unknown strength. Ensure properly rated rigging is used for overhead mounting.
Overhead mounting requires significant experience, including calculating working load limits, knowledge of installation materials, and periodic safety inspections. If you lack these qualifications, do not attempt installation yourself.
Diagram Description: Shows a fixture bracket with a clamp attached, illustrating how the fixture is secured for mounting.
4. Operating Adjustments
The Control Panel
All features and modes are accessed via the 4-button control panel located under the LED display on the rear of the fixture. The buttons are:
- <MENU>: Navigates to the previous higher-level menu item.
- <UP>: Scrolls through menu items and numbers in ascending order.
- <DOWN>: Scrolls through menu items and numbers in descending order.
- <ENTER>: Selects and confirms/stores the current selection.
The LED display shows menu items. To select a menu item, navigate using <UP> and <DOWN>, then press <ENTER>. To return to a previous option without changing a value, press <MENU>.
Control Panel Menu Structure
| Menu Item | Options | Description |
|---|---|---|
| Addr | 001-512 | Set the starting address from 001-512. |
| Chnd | 4Ch, 5Ch, 8Ch | Selects DMX channel mode: 4-channel, 5-channel, or 8-channel. |
| Shnd (show mode) | Shou (show) | Sh01-Sh85 (See Pattern Effects on page 12). |
| Clor (pattern color) | CL01-CL21 (See Color Macros on page 13). | |
| Clbk (not available with some full-pixel preset shows) | Red (0-255), Green (0-255), Blue (0-255) background intensity. | |
| Lost (lost DMX signal default modes) | Hold | Holds the last received DMX signal. |
| Auto | Uses the pattern set in Shou. | |
| Soun | Uses the pattern set in Shou. | |
| Blac | Blackout. | |
| Sens | 000-099 | Mic sensitivity level. |
| Sped | 000-099 | Auto Speed (slow <-> fast). |
| Naun (manual mode) | Red | Red intensity (0-255). |
| Gren | Green intensity (0-255). | |
| Blue | Blue intensity (0-255). | |
| Dinn | Master dimmer (0-255). | |
| Stro | Strobe (see DMX values on page 12). | |
| Tenp | <ENTER> | Displays the internal temperature (°C). |
| Led | <ENTER> | LED backlight: always on, or turns off after 30s. |
| Disp | Norn/Flip | Rotate the menu display by 180°. |
| Ver | <ENTER> | Software version. |
| Defa | <ENTER> | Reset to factory default settings. |
Auto Mode & Sound Active Modes
To use Auto or Sound Active mode, ensure no DMX signal is connected and set the 'Lost DMX' setting to 'Auto' or 'Soun'.
- Navigate to 'Lost', press <ENTER>, choose 'Auto' or 'Soun', and press <ENTER>.
- Navigate to 'Shnd', press <ENTER>.
- Use <UP/DOWN> to highlight 'Shou' (show), select a show from Sh01-Sh85, and press <ENTER>.
- Navigate to 'Clor' (pattern color), select a pattern from CL01-CL21, and press <ENTER>.
- To change the background color, navigate to 'Clbk' (color background). Adjust Red, Green, and Blue intensity levels (this function may not be available for all show patterns).
- To change the pattern speed, navigate to 'Sped' and adjust the setting from 000-099.
Manual Mode
To use Manual mode, ensure the 'Lost DMX' setting is set to 'Blac'.
- Navigate to 'Naun' (manual mode), press <ENTER>.
- Use <UP/DOWN> to highlight 'red', 'gren' (green), 'blue' (blue), 'dinn' (master dimmer), or 'Stro' (strobe), and press <ENTER>.
- Adjust values for each selection from 000-255 as needed.
DMX Values In-Depth (4/5/8-Channel Modes)
| 4CH | 5CH | 8CH | Value | What it does |
|---|---|---|---|---|
| 1 | 1 | 1 | 000 <-> 255 | Dimmer (0% <-> 100%) |
| -- | 2 | 2 | 000 <-> 030 | Strobe: Open |
| 031 <-> 090 | Variable strobe (slow <-> fast) | |||
| 091 <-> 105 | Open | |||
| 106 <-> 165 | Pulse effect (slow <-> fast) | |||
| 166 <-> 180 | Open | |||
| 181 <-> 240 | Random strobe (slow <-> fast) | |||
| 241 <-> 255 | Open | |||
| 2 | 3 | 3 | 000 <-> 255 | Red (0% <-> 100%) |
| 3 | 4 | 4 | 000 <-> 255 | Green (0% <-> 100%) |
| 4 | 5 | 5 | 000 <-> 255 | Blue (0% <-> 100%) |
| -- | -- | 6 | -- | Pattern Effects |
| 7 | -- | Color Macros | ||
| 8 | -- | Effect Speed |
| 4CH | 5CH | 8CH | Value | What it does |
|---|---|---|---|---|
| -- | -- | 6 | 144 <-> 146 | Effect 48 - Swipe 3 segment overlap CW |
| 147 <-> 149 | Effect 49 - Swipe 3 segment overlap CCW | |||
| 150 <-> 152 | Effect 50 - Swipe 4 segment overlap CW | |||
| 153 <-> 155 | Effect 51 - Swipe 4 segment overlap CCW | |||
| 156 <-> 158 | Effect 52 - Swipe 6 segment overlap CW | |||
| 159 <-> 161 | Effect 53 - Swipe 6 segment overlap CCW | |||
| 162 <-> 164 | Effect 54 - Swipe on CW, off CCW | |||
| 165 <-> 167 | Effect 55 - Swipe on CCW, off CW | |||
| 168 <-> 170 | Effect 56 - Swipe 2 segment on/off CW | |||
| 171 <-> 173 | Effect 57 - Swipe 2 segment on/off CCW | |||
| 174 <-> 176 | Effect 58 - Swipe 3 segment on/off CW | |||
| 177 <-> 179 | Effect 59 - Swipe 3 segment on/off CCW | |||
| 180 <-> 182 | Effect 60 - Swipe 4 segment on/off CW | |||
| 183 <-> 185 | Effect 61 - Swipe 4 segment on/off CCW | |||
| 186 <-> 188 | Effect 62 - Swipe 6 segment on/off CW | |||
| 189 <-> 191 | Effect 63 - Swipe 6 segment on/off CCW | |||
| 192 <-> 194 | Effect 64 - 2 segment spin CW | |||
| 195 <-> 197 | Effect 65 - 2 segment spin CCW | |||
| 198 <-> 200 | Effect 66 - 3 segment spin CW | |||
| 201 <-> 203 | Effect 67 - 3 segment spin CCW | |||
| 204 <-> 206 | Effect 68 - 4 segment spin CW | |||
| 207 <-> 209 | Effect 69 - 4 segment spin CCW | |||
| 210 <-> 212 | Effect 70 - 6 segment spin CW | |||
| 213 <-> 215 | Effect 71 - 6 segment spin CCW | |||
| 216 <-> 218 | Effect 72 - 3 segment spin CW | |||
| 219 <-> 221 | Effect 73 - 3 segment spin CCW | |||
| 222 <-> 224 | Effect 74 - Tunnel effect 1, center to perimeter | |||
| 225 <-> 227 | Effect 75 - Tunnel effect 1, perimeter to center | |||
| 228 <-> 230 | Effect 76 - Tunnel effect 2, center to perimeter | |||
| 231 <-> 233 | Effect 77 - Tunnel effect 2, perimeter to center | |||
| 234 <-> 236 | Effect 78 - Tunnel effect 3, center to perimeter | |||
| 237 <-> 239 | Effect 79 - Tunnel effect 3, perimeter to center | |||
| 240 <-> 242 | Effect 80 - Narrow spiral CW | |||
| 243 <-> 245 | Effect 81 - Narrow spiral CCW | |||
| 246 <-> 248 | Effect 82 - Narrow burst, center to perimeter | |||
| 249 <-> 251 | Effect 83 - Narrow burst, perimeter to center | |||
| 252 <-> 254 | Effect 84 - Fireworks full, center to perimeter | |||
| 255 | Effect 85 - Fireworks narrow, center to perimeter | |||
| -- | -- | 7 | 000 <-> 015 | Pattern Color Color 1 - Red (R: 255, G: 000, B: 000) |
| 016 <-> 027 | Color 2 - Candy Apple Red (R: 255, G: 008, B: 000) | |||
| 028 <-> 039 | Color 3 - Scarlet (R: 255, G: 021, B: 000) | |||
| 040 <-> 051 | Color 4 - Orange Red (R: 255, G: 056, B: 000) | |||
| 052 <-> 063 | Color 5 - International Orange (R: 255, G: 084, B: 000) | |||
| 064 <-> 075 | Color 6 - Yellow (R: 255, G: 255, B: 000) | |||
| 076 <-> 087 | Color 7 - Green (R: 000, G: 255, B: 000) | |||
| 088 <-> 099 | Color 8 - Lucent Lime (R: 000, G: 255, B: 058) | |||
| 100 <-> 111 | Color 9 - Spring Green (R: 000, G: 255, B: 127) | |||
| 112 <-> 123 | Color 10 - Bright Turquoise (R: 000, G: 255, B: 206) | |||
| 124 <-> 135 | Color 11 - Aqua (R: 000, G: 255, B: 255) | |||
| 136 <-> 147 | Color 12 - Blue (R: 000, G: 000, B: 255) | |||
| 148 <-> 159 | Color 13 - Lavender (R: 06, G: 000, B: 255) | |||
| 160 <-> 171 | Color 14 - Electric Purple (R: 162, G: 000, B: 255) | |||
| 172 <-> 183 | Color 15 - Magenta (R: 255, G: 000, B: 255) | |||
| 184 <-> 195 | Color 16 - Rose (R: 255, G: 000, B: 008) | |||
| 196 <-> 207 | Color 17 - Hot Pink (R: 255, G: 000, B: 025) | |||
| 208 <-> 219 | Color 18 - Fuchsia (R: 255, G: 000, B: 072) | |||
| 220 <-> 231 | Color 19 - Pink (R: 255, G: 000, B: 150) | |||
| 232 <-> 243 | Color 20 - White (R: 255, G: 000, B: 150) | |||
| 244 <-> 255 | Color 21 - Color Mix (auto) | |||
| -- | -- | 8 | 000 <-> 255 | Effect Speed (slow <-> fast) |
5. Appendix
Keeping Your InfiniPix™ Cyclone As Good As New
To ensure optimal performance, keep the fixture clean, especially in dusty or humid environments. Regularly clean the optics with a suitable glass cleaner to maintain light output quality. Keep fans free of dust and debris to prevent overheating.
Always transport fixtures in protective cases, similar to how valuable musical instruments are transported.
Proper care and common sense are key to maintaining peak performance and ensuring your lighting shows are successful.
Returns (Gasp!)
If a unit is defective or requires service, obtain a Return Authorization (RA) by visiting blizzardpro.com/support and opening a support ticket. Ship the unit using a trackable, pre-paid freight method (e.g., USPS Priority or UPS), preferably in its original box and packing.
When returning your fixture for service, include:
- Contact information (Name, Address, Phone Number, Email address).
- The issued RA number.
- A brief description of the problem/symptoms.
Blizzard Lighting will, at its discretion, repair or replace the fixture. The customer is responsible for any shipping damage incurred during transit to Blizzard Lighting.
Shipping Issues
Damage incurred during shipping is the responsibility of the shipper. Report any damage to the carrier immediately upon receipt. Claims must be made within seven (7) days of receipt.
Tech Specs!
Weight & Dimensions
| Width | 12.4 inches (313.2 mm) |
| Depth | 4.6 inches (116.8 mm) |
| Height | 9.4 inches (260 mm) |
| Weight | 4.1 lbs. (1.9 kg) |
Power
| Operating Voltage | 100-240VAC, 50-60 Hz |
| Power Consumption | 67W, 0.9A, PF: .65 |
| Fuse | 2A 250V |
Light Source
| LED | 325 x 0.2W RGB LEDs |
Optical
| Beam Angle | 120° beam angle |
Thermal
| Max. Operating Temp. | 104° F (40 degrees C) ambient |
Control
| Protocol | USITT DMX-512 |
| DMX Channels | 4/5/8-channel |
| Input/Output | 3-pin XLR male/female |
| Other Operating Modes | DMX-512, M/S, and Standalone |
Warranty
| Warranty | 2-year limited warranty, does not cover malfunction caused by damage to LEDs. |
Dimensional Drawings
The fixture has the following approximate dimensions:
- Width: 12.4 inches (313.2 mm)
- Depth: 4.6 inches (116.8 mm)
- Height: 9.4 inches (260 mm)
- Overall height including bracket: 11.6 inches (293 mm)
Support
LED Lighting Products + IRiS LED Video | Blizzard Lighting
