SENZ WIFI Setup with Google Assistant
This guide provides step-by-step instructions on how to set up and use your SENZ WIFI thermostat with Google Assistant.
System Requirements and Setup Prerequisites
Before proceeding, ensure the following:
- The SENZ WIFI app is downloaded and installed on your smartphone. You can download it from the App Store or Google Play.
- You have set up an account with your username and password in the SENZ WIFI app.
- At least one SENZ WIFI thermostat is connected and configured.
- You can control the SENZ WIFI thermostat(s) through the SENZ WIFI app.
- The Google Home app is downloaded and installed on your smartphone.
Once all prerequisites are met, follow these steps to set up Google Assistant for your SENZ WIFI thermostat:
(Note: App screenshots may vary depending on your smartphone model.)
Step-by-Step Setup Guide
- Open the Google Home app on your smartphone.
- Tap the '+' icon to add a device.
- Tap 'Set up device'.
- Under 'Works with Google', tap 'Have something already set up?'.
- Search for 'SENZ WIFI Thermostat' and tap on it.
- Log in with your SENZ WIFI app username and password.
- When prompted to link your Google account, tap 'Yes, Allow'.
- Tap 'Done' in the top left corner to close the app screen.
- Your SENZ WIFI thermostat(s) should now be visible and available to link with Google Home.
- Select the thermostat (if multiple are available) and tap 'Next' in the bottom right corner.
- Select the location/home for your SENZ WIFI thermostat and tap 'Next' in the bottom right corner.
- Choose a room for the SENZ WIFI thermostat and tap 'Next' in the bottom right corner.
- Assign a location and room for all SENZ WIFI thermostats (if using multiple).
- You will now see your SENZ WIFI thermostats in the Google Home app.
- Try using some of the voice commands listed below, using the name you assigned to your SENZ WIFI thermostat or the room where your Google Assistant-compatible smart speaker is located.
Example Voice Commands
| Desired Action | What Happens | Applicable For | Voice Command Example | Example Text |
|---|---|---|---|---|
| Set specific temperature | Sets the temperature to the desired value. | Single thermostat or group | Hey Google, set [thermostat/group name] to [temperature]. | Hey Google, set Bathroom to 22 degrees. |
| Set thermostat to constant mode | Sets the thermostat to constant mode. | Single thermostat or group | Hey Google, set [thermostat/group name] to HEAT. | Hey Google, set Kitchen to HEAT. |
| Set thermostat to weekly plan | Sets the thermostat to the last used weekly plan (program 1, 2, or 3). | Single thermostat or group | Hey Google, set [thermostat/group name] to AUTOMATIC. | Hey Google, set Living Room to AUTOMATIC. |
| Turn off thermostat (away mode) | Sets the thermostat to constant mode and changes the setpoint to 5°C, effectively turning off the underfloor heating system. | Single thermostat or group | Hey Google, turn [thermostat/group name] OFF. | Hey Google, turn Bathroom OFF. |
| Get current temperature | No changes are made. The current temperature is announced. | Single thermostat or group | Hey Google, what is [thermostat/group name] temperature? | Hey Google, what is Kitchen temperature? |
| Slightly increase temperature | Increases the set temperature by 1.5°C. | Single thermostat or group | Hey Google, increase temperature of [thermostat/group name]. | Hey Google, increase temperature of Living Room. |
| Slightly decrease temperature | Decreases the set temperature by 1.5°C. | Single thermostat or group | Hey Google, decrease temperature of [thermostat/group name]. | Hey Google, decrease temperature of Bathroom. |
Note: For weekly plans, the schedule resumes after 2 hours. For constant mode, this action is permanent.
Contact Information
Czech Republic
Tel: +420 606 069 618 (Comm)
Tel: +420 602 232 969 (Ind)
Email: infoCZ@chemelex.com
