User Guide for XTOOL models including: TPMS3 Tire Pressure Sensor, TPMS3, Tire Pressure Sensor, Pressure Sensor, Sensor
Shenzhen Xtooltech Intelligent Co., Ltd. TPMS3 Tire-Pressure Sensor with 315MHz.433.92MHz 2AW3ITPMS3 2AW3ITPMS3 tpms3
Programmable Universal Tire-Pressure Sensor (With Adjustable Valve Stem) TS101 Universal Tire-Pressure Sensor User Manual (Metal Valve / Clamp-in Style) Disclaimer Please read this manual carefully before installing TS101 universal tire sensor (hereinafter referred to as TS101). For safety reasons, all the installation and maintenance operations should be carried out by trained professionals, with the guidance of vehicle manufacturer. Tire valves are vehicle-safety related component and incorrect installations may cause malfunctions for tire valves or TPMS sensors. Shenzhen Xtooltech Intelligent Co., Ltd. (hereinafter referred to as "Xtooltech") does not assume any liability in case of incorrect installation of the product. Pictures illustrated here are for reference only and this user manual is subject to change without prior notice. Warranty TS101 sensor is guaranteed to be free from material or manufacturing defects for a period of 24 months or 40,000km (25,000 miles), whichever comes first. In case of defections caused by material or workmanship, Xtooltech will repair or replace (according to the situations) the product or parts for free by inspecting the proof of purchase. Xtooltech are not responsible for defects caused in the following circumstances: · Incorrect installation; · Irregular usage; · Damage caused by collision or tire damage; · Exceeding specific using limits of the product. Exploded View Warning · Make sure the sensor has already been programmed before use. We strongly recommend to program the sensor before installing tires. · Do not install a programmed TS101 sensor inside a broken wheel. · To ensure the best performance, do not install valve stems from other manufacturers, or install other parts which is not included inside TS101 sensor. · After finished installation, please test the TPMS system according to the guidance inside user manual from the original vehicle manufacturer, in order to confirm that the sensor is installed correctly. · When the tire is removed, it is highly recommended to replace or service the sensor. If the tire is using rubber valve, the valve stem must be replaced. · When driving vehicles with TS101 installed, the speed should be under 240km/h (150mph) and the tire pressure should be no higher than 900 kPa (9.0 bar or 130.5 psi). Contact Us Official Website: www.xtooltech.com Service Hotline: +86 0755-21670995 +86 0755-86267858 E-mail Address: supporting@xtooltech.com aftersales-services@xtooltech.com Screw Sensor Valve stem, Rubber Washer & Valve Core Assembly Valve Nut & Washer Valve Cap Specifications Sensor Weight (valve not included) Dimensions (valve not included) Max. Pressure Max. Speed Installation Guide approx. 13 g 46.1 x 25 x 16.2mm (1.81" x 0.98" x 0.64") 900 kPa (9.0 bar or 130.5 psi) 240 km/h (150mph) Every time the tire been repaired, dismantled, or uninstalling & replacing TS101 sensors, make sure that the original rubber washer, screws, nuts and valve stems from TS101 are used in order to keep good air tightness. If the tire or wheel is damaged externally, the TS101 sensor must be replaced. The torque of the valve tighening screw should be 4Nm (2.95 lb·ft). 1. Deflate & Uninstall Tire Take off the valve cap and the valve core to deflate the tire. Then, use tools (or machines) to uninstall the tire from the rim. *In case of replacing the sensor only, deflate the tires, pry up the tire near valve stem until the sensor is exposed. Do not break the tire bead near the valve stem, or the original sensor may get damaged. 2. Uninstall Sensor Take off the valve nut, washer and screw from the valve stem. Then, take the sensor assembly out from the rim. * Here shows the process of uninstalling TS101 sensor. If you have problems when uninstalling other sensors, please check the repair manual or installation guide for uninstalling steps. 3. Install TS101 Sensor Use the screw to assembly the valve core and the TS101 sensor tightly. Uninstall the valve nut, washer and valve cap. Adjust the angle of the sensor, then insert the valve core inside the valve hole, and make sure that the TS101 sensor is inside the rim. Install the valve nut and washer back to the valve core. Lock the nut with 4Nm (2.95 lb·ft) of torque. Install the tire back, inflate the tire to standard tire pressure (see vehicle nameplate) and install the valve cap. Shenzhen Xtooltech Intelligent Co., Ltd. Address: 17&18/F, A2 Building, Creative City, Liuxian Avenue, Nanshan District, Shenzhen, China For cooperation or business inquiry, please contact: marketing@xtooltech.comMicrosoft: Print To PDF