Mesquul Upgraded Simple Loud Alarm Clock

Locations of Controls

• 1. Set Time: Button to set current time.
• 2. Dimmer: Button to adjust display brightness.
• 3. Alarm 1: Button to set/activate Alarm 1.
• 4. Alarm 2: Button to set/activate Alarm 2.
• 5. [Mode Button]: Button for selecting alarm modes.
• 6. [Plus Button]: Button to increase values or move forward.
• 7. Volume: Button to adjust alarm volume.
• 8. 12/24H DST: Button to switch between 12/24 hour format and enable/disable Daylight Saving Time.
• 9. Snooze/OK/Night Light: Button for snooze, confirming settings, or activating the night light.
• 10. DST Indicator: Indicator light for Daylight Saving Time.
• 11. AM Indicator: Indicator light for AM time.
• 12. PM Indicator: Indicator light for PM time.
• 13. Week Display: Shows the current day of the week.
• 14. Alarm 1 Indicator: Indicator light for Alarm 1 status.
• 15. Alarm 2 Indicator: Indicator light for Alarm 2 status.
• 16. LOW Dimmer Indicator: Indicator light for low brightness mode.
• 17. Battery Compartment: Housing for backup batteries.
• 18. Speaker: Produces alarm sounds.
• 19. Vibration Intensity: Switch to adjust bed shaker strength.
• 20. Day Selection for Alarm 1: Setting for which days Alarm 1 will be active.
• 21. Day Selection for Alarm 2: Setting for which days Alarm 2 will be active.
• 22. DC Jack: Port for connecting the power adapter.
• 23. USB Output Port: Port for charging external devices.
• 24. Vibrator Insert Port: Port for connecting the bed shaker.
• 25. Night Light: Feature to provide illumination.

Package Lists

• 1x Alarm Clock
• 1x Adapter (DC 5V/2A)
• 1x Cable (Length: 1.5M/5ft)
• 1x User Manual
• 1x Bed Shaker (Length: 1.8M/6ft)

Installation Notes

1. Connect the power cord to the DC jack, and plug into a 100~240V AC wall power outlet.
2. Install 2pcs 1.5V "AAA" batteries into the proper terminals in the battery compartment to memorize the time setting. The alarm will ring in case of power outage.

Note: Batteries are not included and don't support time display or any other functions.

Visual Description: Battery compartment for two "AAA" batteries [not included]. DC power adapter with plug [DC power].

Time Setting

1. Press the "TIME" button to enter the time setting mode. The week digits will start flashing. Use the [plus-button] and [minus-button] to select the day of a week.
2. Press the "TIME" button again to enter the hour setting mode. The hour digits will start flashing. Use the [plus-button] and [minus-button] to adjust the hour display.
3. Press the "TIME" button again to enter the minute setting mode. The minute digits will start flashing. Use the [plus-button] and [minus-button] to adjust the minute display.
4. Press the "TIME" button to confirm the time, or wait for another 10 seconds to confirm automatically.

Visual Description: Four sequential diagrams show the clock display during time setting: 1. Week digits flashing, 2. Hour digits flashing, 3. Minute digits flashing, 4. Final time displayed.

Alarm Setting

Set the Alarm

1. Slide the Period Range switch for Alarm 1 on the back to choose the period range (MON-SUN, MON-FRI, SAT-SUN).
2. Press the "AL1" button; the Alarm 1 indicator will light up.
3. Press the "AL1" button again; the hour digits will start flashing. Use the [plus-button] and [minus-button] to set the hour.
4. Press the "AL1" button once more; the minute digits will start flashing. Use the [plus-button] and [minus-button] to set the minute.
5. Press the "AL1" button again to save the alarm settings; the [Alarm 1 Icon] starts flashing.
6. Repeat pressing the [minus-button] or [plus-button] to choose the wake-up modes: "Single Buzzer", "Single Vibrator", or "Buzzer + Vibrator", and press the "AL1" button again to confirm your choice.

Visual Description: Diagrams illustrate the steps: 1. Period Range switch. 2. Alarm 1 indicator lit. 3. Hour digits flashing. 4. Minute digits flashing. 5. Alarm 1 icon flashing. 6. Selection of wake-up modes.

Cancel Alarm

Hold press the "AL1" button for 3 seconds until the Alarm 1 indicator disappears from the display. The alarm will never ring again.

Note: The setting method for Alarm 2 is the same as Alarm 1.

Set the Wake up Mode

• Wake up by buzzer sound only: Only the buzzer indicator lights up.
• Wake up by bed shaker only: Only the vibrator indicator lights up.
• Wake up by both buzzer and bed shaker: Both the buzzer indicator and vibrator indicator light up.

Visual Description: Icons representing a sound wave, a vibrating bed, and both combined are shown next to the descriptions.

Set the Vibration Intensity

Plug in the vibrator and slide the Vibration Intensity switch on the back to adjust the 3-level strength of the bed shaker (Low, Medium, High).

Visual Description: An illustration shows the vibrator plug and a switch with labels L, M, H.

Set the Volume

Repeat-press the "Vol" button to adjust alarm volume.

Visual Description: A display shows "003" indicating the volume level.

Turn off Alarm & Snooze Mode

1. When the alarm goes off, press the "SNOOZE/OK/LIGHT" button. The alarm icon will be flashing, and the alarm will stop temporarily, ringing again after 9 minutes. (SNOOZE mode can be recycled 9 times).
2. During the alarm ringing, press the "AL1" or "AL2" button to turn off the alarm for the current day. The alarm will ring again the next day.
3. If there is no operation after the alarm goes off, the alarm will automatically stop after 60 minutes and ring again the next day.

12/24H Time & DST Setting

1. Short press the "12/24H DST" button to switch the 12H/24H time format. In the 12-hour format, an AM/PM icon will be displayed.
2. Hold press the "12/24H DST" button to turn on or off the DST function.

Visual Description: Diagrams show the clock switching between 10:30 (AM/PM indicator) and 22:30 (24-hour format), and then showing 10:30 and 11:30 with DST enabled/disabled.

Night Light

When there is no alarm clock ringing, press the "SNOOZE/OK/LIGHT" button to turn on the night light. Repeat-press it to adjust the brightness: High-Medium-Low-OFF.

Brightness Setting

1. Display screen brightness (default L04). Repeat-press the "DIM" button to adjust the brightness of the digits display. It cycles through levels L01 to L05.
2. When in L01 level, the [LOW DIMMER Icon] appears. The icon will disappear after 20 seconds of display if no operation. Press the "DIM" button once more, the [LOW DIMMER Icon] will display again.

Visual Description: A display shows "L.04" indicating the brightness level. Another illustration shows the "LOW DIMMER" icon.

Charging Other Devices

This alarm clock has a USB port, allowing you to charge your mobile device simultaneously (charging cable not included). The maximum charging current is 1 Ampere.

Visual Description: An illustration shows the USB output port on the back of the device.

Warranty Service

45-Day Full Refund

If you are unsatisfied with the product or encounter any issues, please contact Mesquul promptly for a full refund or technical support.

18-Month Warranty

Within 18 months, if the product has any quality issues, please contact Mesquul for a replacement or partial refund.

Lifetime Free Customer Support

Mesquul provides lifelong free customer support. If you have any questions or concerns, please do not hesitate to reach out.