User Manual for PANTUM models including: 4020WM, 2AEGO4020WM, CDW-G4822BU-01 WiFi Module, WiFi Module
Zhuhai Pantum Electronics Co., Ltd 4020WM WIFI Module 2AEGO4020WM 2AEGO4020WM 4020wm
File Info : application/pdf, 13 Pages, 1.64MB
DocumentDocumentUser Guide CDW-G4822BU-01 WiFi Module It is recommended that you read this Guide carefully before using the printer WiFi Module CDW-G4822BU-01 1. Overview The CDW-G4822BU-01 is based on RTL8822BU-CG, that support 2-stream 802.11ac solutions with Multi-user MIMO (Multiple-Input, Multiple-Output) with Wireless LAN (WLAN) USB2.0 network interface controller. It combines a WLAN MAC, a 2T2R capable WLAN baseband, and RF in s single chip. The CDW-G4822BU-01 provides a complete solution for a high-performance integrated wireless . 2. Features IEEE 802.11a/b/g/n/ac compatible WLAN 5MHz / 10MHz / 20MHz / 40MHz / 80MHz bandwidth transmission Complies with USB2.0 for WLAN controller Dual-band 2T2R mode with data rate up to 867Mbps Support 802.11ac 2x2,Wave-2 compliant with MU-MIMO Complete 802.11n MIMO solution for 2.4GHz and 5Ghz band Maximum PHY data rate up to 173.3 Mbps using 20MHz bandwidth, 400Mbps using 40MHz bandwidth, and 866.7Mbps using 80MHz bandwidth DSSS with DBPSK and DQPSK, CCK modulation with long and short preamble, OFDM with BPSK, QPSK, 16QAM,64QAM and 256QAM modulation. Convolutional Coding Rate: 1/2, 2/3, 3/4,and 5/6 Support STBC, Support LDPC Build-in both 2.4GHz and 5GHz PA, Build-in both 2.4GHz and 5GHz LNA Enhanced WLAN Coexistence Control to improve transmission quality in different profiles Page 2 3. Precautions Pantum Regulatory Type/Model Number CDW-G4822BU-01; FCC ID:2AEGO4020WM 5G band I (5150-5350MHz) indoor use only. 5.Hereby, [Zhuhai Pantum Electronics Co., Ltd.] declares that the radio equipment type [CDWG4822BU-01] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.http:WWW.PANTUM.COM FCC regulatory compliance statement §15.19 Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. §15.21 Information to user Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. List of applicable FCC rules: 47 CFR Part 15, Subpart C 15.203 47 CFR Part 15, Subpart C 15.205 47 CFR Part 15, Subpart C 15.207 47 CFR Part 15, Subpart C 15.209 47 CFR Part 15, Subpart C 15.247 47 CFR Part 15, Subpart E 15.407 47 CFR Part 2 2.1091 Summarize the specific operational use conditions This module can be used in IOT devices, the input voltage to the module is nominally 5V. Only the embedded integral antenna is allowed. Any other external antenna is prohibited. Limited module procedures This module is not a limited module. Trace antenna designs The antenna is not a trace antenna. RF exposure considerations This Module complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Antennas If you desire to increase antenna gain and either change antenna type or use same antenna type certified, a Class II permissive change application is required to be filed by us, or you (host manufacturer) can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application. Label and compliance information Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. following: "Contains FCC ID: 2AEGO4020WM" any similar wording that expresses the same meaning may be used. § 15.19 Labelling requirements shall be complied on end user device. Labelling rules for special device, please refer to §2.925, § 15.19 (a)(5) and relevant KDB publications. For E-label, please refer to §2.935. Information on test modes and additional testing requirements The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. The module is limited to installation in mobile application, a separate approval is required for all other operating configurations, including portable configurations with respect to §2.1093 and difference antenna configurations. Additional testing, Part 15 Subpart B disclaimer This modular transmitter is only FCC authorized for the specific rule parts listed on our grant, host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer in any case shall ensure host product which is installed and operating with the module is in compliant with Part 15B requirements. Please note that For a Class B or Class A digital device or peripheral, the instructions furnished the user manual of the end-user product shall include statement set out in. §15.105 Information to the user or such similar statement and place it in a prominent location in the text of host product manual. Original texts as following: For Class B Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. 4. FrequencyBand: Frequency Band: WiFi 2.4GHz: WiFi 5GHz: WiFi 5.8GHz: 2412MHz - 2462MHz 5180MHz - 5320MHz, 5500MHz - 5700MHz 5745MHz - 5825MHz maximum output power : (Declaration for EU Compliance) Radio Frequency Output Power WLAN 2.4GHz 2412-2462MHz 18.58 dBm EIRP WLAN 5GHz 5180-5320MHz 5500-5700MHz 20.48 dBm EIRP 21.73 dBm EIRP WLAN 5.8GHz 5745-5825MHz 13.58 dBm EIRP WiFi Module CDW-G4822BU-01 3. General Specification Model Product Name Major Chipset Standard Data Transfer Rate Modulation Method Frequency Band Spread Spectrum Operation Mode Antenna gain CDW-G4822BU-01 WIFi 11a/b/g/n/ac 2T2R Realtek RTL8822BU-CG IEEE 802.11a/b/g/n/ac 1,2,5.5,6,11,12,18,22,24,30,36,48,54,60, 90,120 and maximum of 867Mbps CCK//DBPSK/DQPSK/QPSK/16-QAM/ 64-QAM/256QAM 2412MHz - 2462MHz,5180MHz - 5320MHz, 5500MHz -5700MHz,5745MHz - 5825MHz IEEE 802.11b: DSSS (Direct Sequence Spread Spectrum) IEEE802.11a/g/n/ac: OFDM (Orthogonal rthogonal Frequency Division Multiplexing) Ad hoc, Infrastructure 2 dBi Security Interface Operating Temperature Storage Temperature Humidity Dimension WEP, TKIP, AES, WPA, WPA2 USB 2.0 -20~ +70° C ambient temperature -40 ~ 85°C ambient temperature 5 to 90 % maximum (non-condensing) 46.5x40x7.6mm (LxWxH)±0.2mm 4. DC Characteristics Symbol VD33 VD10 VIH VIL VOH VOL Parameter 3.3V I/O supply Voltage 1.05V Core Supply Voltage Input high Voltage Input low Voltage output high Voltage output low Voltage Min. 3.0 0.945 2.0 -2.97 0 Typ. Max Units 3.3 3.6 V 1.05 1.155 V 3.3 3.6 V 0 0.9 V -- 3.3 V -- 0.33 V Page 3 5. Dimension & Pin Assignments 40.00 WiFi Module CDW-G4822BU-01 46.50 3.60 19.00 R2.00 32.90 R2.00 PIN6 PIN1 NO Name 1 UV+ 2 USB_DM 3 USB_DP 4 GND 5 BT_REG_ON 6 ON/OFF 6.40 7.60 6.60 1.60 Type Description - Power supply 5V is requiredMAX 5.5V I/O USB data- I/O USB data+ - Ground connections I GPIO Control BT device enabled I Control "EN" of DC-DC,High level (default) 6. Key material list Type Crystal WIFI IC PCBA VER P/N 40Mhz RTL8822BU 63822BU G4822BU JWT FK , SFJ RTL A,O,S supplier JWT 40MHz 3225 FK 40MHz 3225 SFJ 40MHz 3225 Page 4 7. Modular photo WiFi Module CDW-G4822BU-01 Dimension TOP VIEW 46.5x40x7.6mm (LxWxH)±0.2mm BOTTOM VIEW 8. Electrical Characteristics 7.1 WiFi Section: 2.4GHz RF Specification Feature Description WLAN Standard IEEE 802.11a/b/g/n/ac WiFi compliant Frequency Range 2.400 GHz ~ 2.497GHz (2.4 GHz ISM Band) Number of Channels CH1-CH11(America, Canda),CH1-CH13(Europe,China),CH1-CH14(Japan) Modulation 802.11b : DQPSK, DBPSK, CCK 802.11 g/n : OFDM /64-QAM,16-QAM, QPSK, BPSK Receive - 1Mbps PER @ -93 dBm, typical Sensitivity (11b,20MHz) - 2Mbps PER @ -91 dBm, typical @8% PER - 5.5Mbps PER @ -88 dBm, typical Receive - 11Mbps - 6Mbps PER @ -86 dBm, typical PER @ -90 dBm, typical Sensitivity (11g,20MHz) - 9Mbps PER @ -89 dBm, typical @10% PER - 12Mbps PER @ -88 dBm, typical Page 5 WiFi Module CDW-G4822BU-01 - 18Mbps PER @ -85 dBm, typical - 24Mbps PER @ -82 dBm, typical - 36Mbps PER @ -79 dBm, typical - 48Mbps PER @ -74 dBm, typical - 54Mbps PER @ -72 dBm, typical - MCS=0 PER @ -90 dBm, typical - MCS=1 PER @ -87 dBm, typical - Receive - Sensitivity (11n,20MHz) - @10% PER - MCS=2 MCS=3 MCS=4 MCS=5 PER @ -85 dBm, typical PER @ -81 dBm, typical PER @ -78 dBm, typical PER @ -73 dBm, typical - MCS=6 PER @ -72 dBm, typical Receive - MCS=7 - MCS=0 PER @ -70 dBm, typical PER @ -87 dBm, typical Sensitivity (11n,40MHz) - MCS=1 PER @ -84 dBm, typical @10% PER - MCS=2 PER @ -82 dBm, typical - MCS=3 PER @ -79 dBm, typical - MCS=4 PER @ -75 dBm, typical - MCS=5 PER @ -71 dBm, typical - MCS=6 PER @ -69 dBm, typical Maximum Input Level - MCS=7 PER @ -68 dBm, typical 802.11b : -10 dBm 802.11g/n : -20 dBm 7.2 5GHz RF Specification Feature WLAN Standard Frequency Range Number of Channels Modulation Description IEEE 802.11a/n/ac 2x2, WiFi compliant 5.15GHz ~ 5.35GHz 5.725GHz ~ 5.85GHz 5.0GHzPlease see the table 802.11a : OFDM /64-QAM,16-QAM, QPSK, BPSK 802.11n : OFDM /64-QAM,16-QAM, QPSK, BPSK 802.11ac : OFDM /256-QAM - 6Mbps PER @ -89 dBm, typical Page 6 WiFi Module CDW-G4822BU-01 Receive Sensitivity (11n,20MHz) @10% PER Receive Sensitivity (11n,40MHz) @10% PER Receive Sensitivity (11ac,20MHz) @10% PER - 9Mbps PER @ -88 dBm, typical - 12Mbps PER @ -87 dBm, typical - 18Mbps PER @ -84 dBm, typical - 24Mbps PER @ -81 dBm, typical - 36Mbps PER @ -78 dBm, typical - 48Mbps PER @ -73 dBm, typical - 54Mbps PER @ -72 dBm, typical - MCS=0 PER @ -89 dBm, typical - MCS=1 PER @ -86 dBm, typical - MCS=2 PER @ -84 dBm, typical - MCS=3 PER @ -81 dBm, typical - MCS=4 PER @ -77 dBm, typical - MCS=5 PER @ -72 dBm, typical - MCS=6 PER @ -71 dBm, typical - MCS=7 PER @ -68 dBm, typical - MCS=0 PER @ -86 dBm, typical - MCS=1 PER @ -83 dBm, typical - MCS=2 PER @ -81 dBm, typical - MCS=3 PER @ -78 dBm, typical - MCS=4 PER @ -74 dBm, typical - MCS=5 PER @ -70 dBm, typical - MCS=6 PER @ -68 dBm, typical - MCS=7 PER @ -67 dBm, typical - MCS=0, NSS1 PER @ -87 dBm, typical - MCS=1, NSS1 PER @ -85 dBm, typical - MCS=2, NSS1 PER @ -83 dBm, typical - MCS=3, NSS1 PER @ -80 dBm, typical - MCS=4, NSS1 PER @ -76 dBm, typical - MCS=5, NSS1 PER @ -71 dBm, typical - MCS=6, NSS1 PER @ -70 dBm, typical - MCS=7, NSS1 PER @ -69 dBm, typical - MCS=8, NSS1 PER @ -65 dBm, typical - MCS=0, NSS1 PER @ -85 dBm, typical - MCS=1, NSS1 PER @ -82 dBm, typical - MCS=2, NSS1 PER @ -80 dBm, typical - MCS=3, NSS1 PER @ -77 dBm, typical Page 7 WiFi Module CDW-G4822BU-01 Receive Sensitivity (11ac,80MHz) @10% PER Maximum Input Level - MCS=4, NSS1 PER @ -74 dBm, typical - MCS=5, NSS1 PER @ -69 dBm, typical - MCS=6, NSS1 PER @ -68 dBm, typical - MCS=7, NSS1 PER @ -67 dBm, typical - MCS=8, NSS1 PER @ -62 dBm, typical - MCS=9, NSS1 PER @ -58 dBm, typical - MCS=0, NSS1 PER @ -82 dBm, typical - MCS=1, NSS1 PER @ -79 dBm, typical - MCS=2, NSS1 PER @ -77 dBm, typical - MCS=3, NSS1 PER @ -73 dBm, typical - MCS=4, NSS1 PER @ -70 dBm, typical - MCS=5, NSS1 PER @ -67 dBm, typical - MCS=6, NSS1 PER @ -65 dBm, typical - MCS=7, NSS1 PER @ -63 dBm, typical - MCS=8, NSS1 PER @ -59 dBm, typical - MCS=9, NSS1 PER @ -55 dBm, typical 802.11a/n/ac : -20 dBm Page 8 9. Packing information WiFi module WiFi Module CDW-G4822BU-01 clapboard A12: 420*335mm Pearl cotton: 420*335*45mm 126PCS/laye Loading the outer box Pearl cotton Antistatic test Red antistatic pearl cotton 1008pcs/8 layer Red antistatic plastic bag Desiccant 50g Paper corner/4pcs Outer box K=A435*350*415mm 1008pcs/BOX 4pcs paper protector ESD CAUTION The CDW-G4822BU-01 is ESD (electrostatic discharge) sensitive device and may be damaged with ESD or spike voltage. Although CDW-G4822BU-01 is with built-in ESD protection circuitry, please handle with care to avoid the permanent malfunction or the performance degradation. Page 9 Connector SPE WiFi Module CDW-G4822BU-01 Page 10