Best Video Lights | Lights for Video Studio | COLBOR
User Manual for COLBOR models including: W100 Video Light, W100, Video Light, Light
Apr 9, 2024 — Product design and specifications are subject to change without prior notice. Page 3. Product Instructions. Light Installation. Hold the COB cover with the ...
File Info : application/pdf, 9 Pages, 1.30MB
DocumentDocumentW100 Video Light User Manual Thank you for choosing COLBOR product. Please read this manual carefully before use and follow all instructions mentioned herein. Caring For Your COLBOR Product Keep corrosive chemicals, liquids and heat source away from the product to prevent mechanics damage. The product is not waterproof. Do not leave the product unattended while in use. Keep out of reach of children. Do not handle with wet hands. Do not touch the hot COB surface. Please do not block the ventilation and do not look at the light directly when it is on. Do not attempt to disassemble or modify the product. Doing so voids warranty. Please have the product checked or repaired by authorized technicians if any malfunctions happened. Disconnect from the power supply when it is not in use. Do not cover, inverted COB and radiator for high temperature, do not cover, inverted, do not touch the lamp holder and radiator vent with your hands when the product in use. Do not use any power adapter of other products to avoid the lamp malfunction. Malfunction may be caused by dropping, impact of external force. Failure to follow all the instructions may result in mechanics damage. Our company reserves the right of final interpretation of the product. Product design and specifications are subject to change without prior notice. Note Please use the included power adapter to avoid damage. When powering via the COLBOR POWER GRIP, use the D-Tap to DC cable to connect the D-Tap port on the battery and the DC port on the light. Please do not use the Type-C port on the battery for powering. Product Instructions Power Button Wireless Control Setting Button Brightness Control Wheel Color Temperature Control Knob OLED Screen Air Inlet NFC Detection Area COLBOR Mount Lock COB Lamp Beads COLBOR Mount 1/4" Hole Screw Battery Contacts Type-C Port DC Port Light Installation 1. Removal of COB protection cover Hold the COB cover with the COLBOR Mount tenon and rotate it as the direction of the arrow. Note: Be sure to remove cob protective cover and cob protective film before use. 2. Installation and removal of reflector Installation of reflector: Align the reflector with the groove around the lamp head and clip it in, turn the reflector as the direction of the arrow, and the reflector installation will be completed after the top rod rebounds. Removal of reflector: Follow the instructions of "Removal of COB protection cover". 3. Power Connection (1) Power with power adapter Connect the power adapter, align the DC power jack of the lamp body, and then power on through the cable after stable. Do not suspend the power adapter in the air. Use wire rings to hang it on the lamp stand. (2) Power with COLBOR Power Grip Secure the battery handle with the light body's 1/4" screw hole at the top and connect via the D-Tap to DC cable for powering. Operation Instructions 1. Power On/Off Power OnConnect to the power source then long press the power button. Power OffLong-press the power button to turn off. 2. Wireless Connection Short press the remote control button to switch between 2.4GHz (CTRL1 remote) and APP (COLBOR Studio APP) control modes. Long-press the button to start pairing. 3. Brightness Adjustment Roll the brightness adjustment wheel for adjustment. Short press the wheel side to select preset brightness(0%, 25%, 50%, 75%, 100%). 4. Color Temperature Adjustment Rotate the color temperature control knob for color temperature adjustment. Short press the knob to select preset color temperature(2700K, 3200K, 4300K, 5600K, 6500K). 5. EFF Control/Fan Mode Control Connect to the APP for Fan settings and EFF settings. 6. Status Icon Description APP Connection Status Icon 2.4GHz Control Mode, available for controlling via CTRL1 remote. APP Control Mode, available for controlling via COLBOR Studio APP. Fan Status Icon Smart Mode. The product will adjust the fan speed according to the internal detected temperature to ensure that it is in optimal working condition. Performance Mode. Fan runs at the highest speed to ensure heat dissipation. Quiet Mode. The fan keeps running at low speed for minimum noise, and overheating protection will be activated if the product temperature is higher than the alarm value. Power Status Icon Error Icon DC Powering. NTC errorCOB temperature sensor error, please contact the after service. Fan error, please contact the after service. Specifications CRI/TLCI SSI TM-30-18 Color Temperature Range Beam Angle Illumination COB Output Power Power Light Working Voltage Cooling Mode Connector Body Material Light Dimension Light Weight Operating Temperature 97/99 D32:88 D56:71 Rf:94/Rg:101 2700K-6500K(±150K) 120° See the Form 1 Below 90W 100W(Max) DC 20V5A Smart/Quite/Performance DC/Type-C PC+ABS 157*43*93mm 345g -10~40 Packing List W100 Video Light x1 Plum Tail Cable x1 Power Adapter (with Wire Lanyard) x1 Reflector x1 COB Cover x1 Dome x1 Power adapters may vary according to sales region. Warranty Card x1 Form 1 Illumination CCT 1m 3m 5m 2700K Light Base Reflector 2,790 5,270 408 665 221 314 3200K Light Base Reflector 3,010 5,690 453 718 247 339 4300K Light Base Reflector 3,300 6,360 499 776 261 376 4500K Light Base Reflector 3,340 6,420 495 790 264 380 5600K Light Base Reflector 3,450 6,790 512 843 275 398 6500K Light Base Reflector 3,510 7,02 519 851 282 396 The data is given from testing in a laboratory. WARRANTY Warranty Period Thank you for purchasing COLBOR products. 1.Customers are entitled to free replacement or repair service in case of quality defect(s) found in the product under normal use within 30 days upon receipt of the product. 2.Original COLBOR products are entitled to 12-month limited warranty service. The warranty period begins on the date of purchase of brand new, unused products by the first end-user. Within the warranty period, if product defect or failure is attributable to material defection or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee). Warranty Exclusions and Limitations 1.Faults resulted from inappropriate use of a product without following its operation specification 2.Artificial damage, e.g. crash, squeeze, scratch, soaking, exposing to rain or damp 3.Modifications to a product by its user or a third party without prior written consent of COLBOR, e.g. replacement of element or circuit, label alteration 4.The code on product is inconsistent with that of warranty certificate, or the code on the product or warranty certificate is altered or torn off 5.All consumable accessory attached to a product, like cable, cover 6.Faults as a result of force majeure, such as fire, flood, lightning, etc. Warranty Claim Procedure 1.If failure or any problem occurs to your product after purchase, please contact a local agent for assistance, or you can always contact COLBOR's customer service through email. 2.Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents is missing, only sales return or chargeable service will be provided. 3.If the COLBOR product is out of the warranty coverage, the service and the parts cost will be charged. Guangzhou Zhiying Technology Co., Ltd Room 2401, 24 / F, South Tower, Lisheng Plaza, No. 68 Huadi Avenue, Liwan District, Guangzhou, China, 510000 support@colborlight.com www.colborlight.com