Tannoy CVS Series In-Ceiling Loudspeakers

Product Overview

The Tannoy CVS Series offers a range of in-ceiling loudspeakers designed for high-level music and speech reinforcement applications, delivering exceptional sonic quality with uncompromised reliability. These loudspeakers are intended for indoor dry use.

Models include:

• CVS 301 / CVS 301-BK: 3" In-Ceiling Loudspeaker for Installation Applications
• CVS 401 / CVS 401-BK: 4" Coaxial In-Ceiling Loudspeaker for Installation Applications
• CVS 601 / CVS 601-BK: 6.5" Coaxial In-Ceiling Loudspeaker for Installation Applications
• CVS 801 / CVS 801-BK: 8" Coaxial In-Ceiling Loudspeaker for Installation Applications
• CVS 801S: 8" In-Ceiling Subwoofer Loudspeaker for Installation Applications
• CVS 801S LZ: 8" In-Ceiling Subwoofer Loudspeaker for Installation Applications - Low Impedance Operation Only

A visual representation of the speaker range shows multiple circular grilles of varying sizes, mounted within cylindrical enclosures.

Important Safety Instructions

⚠ CAUTION: RISK OF ELECTRIC SHOCK! DO NOT OPEN!

⚠ ATTENTION: RISQUE D'ÉLECTROCUTION! NE PAS OUVRIR!

Terminals marked with a [Electrical Hazard] symbol carry electrical current of sufficient magnitude to constitute a risk of electric shock. Use only high-quality professional speaker cables with 1/4" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.

The [Warning] symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure – voltage that may be sufficient to constitute a risk of shock.

The [Manual/Information] symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.

Caution: To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside. Refer servicing to qualified personnel.

Caution: To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus.

Caution: These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel.

General Safety Guidelines:

• Read and keep these instructions.
• Heed all warnings and follow all instructions.
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit your outlet, consult an electrician for replacement.
• Protect the power cord from being walked on or pinched.
• Use only attachments/accessories specified by the manufacturer.
• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. Use caution when moving cart/apparatus combinations to avoid injury from tip-over.
• Unplug this apparatus during lightning storms or when unused for long periods of time.
• Refer all servicing to qualified service personnel.
• The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.
• Where the MAINS plug or an appliance coupler is used as the disconnect device, it shall remain readily operable.
• Do not install in a confined space, such as a bookcase or similar unit.
• Do not place naked flame sources, such as lighted candles, on the apparatus.

Product Disposal:

The [WEEE Disposal Symbol] indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). Proper disposal helps prevent negative impacts on the environment and human health.

Please keep the environmental aspects of battery disposal in mind. Batteries must be disposed of at a battery collection point [Battery Disposal Symbol].

This apparatus may be used in tropical and moderate climates up to 45°C.

Introduction

Thank you for purchasing this Tannoy Ceiling loudspeaker. This product range is suited for high-level music and speech reinforcement applications requiring exceptional sonic quality with uncompromised reliability. The loudspeakers in this series are for indoor dry use.

Unpacking

Every Tannoy product and accessory is carefully inspected before packing. After unpacking, please inspect your product to make sure no damage has occurred in transit. In the unlikely event of any damage, notify your dealer immediately and retain your shipping carton, as your dealer may ask you to return the faulty unit for inspection.

Each CVS loudspeaker is packed in pairs and provided with the following standard accessories: C-Ring, tile-bridge kit, cut-out template, and paint mask. A plaster (mud) ring and 48" tile rail are also available as optional extras.

Safety Notices

Some regional construction codes require the use of a secondary method of securing loudspeakers in ceilings to provide a backup support. A secondary support line should be attached from the safety loop on the rear of the product to a secure point on the ceiling. Consult the relevant construction codes in your region.

When using a power driver to install the product, it is essential to use the correct torque level settings to avoid over-tightening and damage to the ceiling material or clamps. Recommended torque setting: 1.5 Nm.

Tannoy will not be held responsible for any damages caused by the improper installation of these loudspeakers.

SAFETY NOTE: In order to comply with relevant fire safety regulations (e.g., BS 5839: 1998), it is required that in the event of fire, the failure of the circuit to which the loudspeaker is connected does not occur before evacuation of the building is complete. Suitable measures include: use of terminal blocks with a melting point of not less than 650°C (e.g., ceramic materials), or terminal blocks of a lower melting point protected with thermal insulation, or terminal blocks designed so that on melting, an open-circuit or a short-circuit does not occur.

Product Feature Identification (CVS-601 shown)

Side View: Depicts the speaker enclosure from the side, showing its depth and mounting mechanism.

Front View: Shows the front of the speaker, highlighting the grille, mounting screws, and tap selector.

Rear View: Illustrates the back of the speaker, showing the input terminal connector, rotating mounting tabs, secondary safety tab, input terminal cover, speaker cable clamp, and optional cable gland for EN5424 applications.

• Mounting screws
• Tap selector
• Input terminal connector
• Rotating mounting tabs
• Secondary Safety Tab
• Input terminal cover
• Speaker cable clamp
• Optional cable gland for EN5424 applications

Note: The auxiliary support ring is not shown in these diagrams.

Accessories

Standard Accessories:

• C-Ring: A circular mounting ring for ceiling tiles.
• Tile bridge kit: Used for installation into suspended ceiling tiles, providing support.
• Paint Mask: A mask to protect the speaker grille during painting. It includes instructions for use: 1. Fit paint mask over driver. 2. Insert four tabs into grille recess before spray paint. 3. Break the blind hole to remove mask.
• Cut-out template: A template for marking the correct hole size on the ceiling tile. Dimensions shown are approximately 484mm x 242mm with a cutout diameter of Ø222mm.

Optional Accessories:

• Plaster (Mud) Ring: For pre-installation into newly constructed, non-suspended ceilings.
• 48" Tile Rail: An additional support rail for larger ceiling tiles.

Installation Guide for Suspended Ceilings

Note: Speaker images are for guidance only and may not exactly represent your particular model.

1. Remove the ceiling tile from its frame and place it on a flat surface. Mark the cut-out area on the ceiling tile by tracing around the provided template.
2. Cut out the hole in the ceiling tile using a circular saw or pad saw. Place the C-ring and tile-bridge on top of the ceiling panel, aligning the C-ring over the hole, and screw the C-ring to the tile bridge using the provided fixings.
3. Slide the speaker assembly through the hole and turn the screws on the front of the speaker to extend the mounting wings. Tighten the screws until a firm grip is achieved. If using a power driver, Tannoy recommends a torque setting of 1.5 Nm. DO NOT OVERTIGHTEN!
4. Slide the tile panel back into the suspended ceiling. The tile bridge ends will catch over the railings, supporting the weight of the speaker.
5. Connect a secondary support line to the safety tab. Some construction codes require use of this secondary support point, which should connect to a separate secure support point using a suitable support line. Consult construction codes in your region.
6. Refer to page 15 for wiring and set-up instructions.

Installation Guide for Drywall Ceilings

Note: Speaker images are for guidance only and may not exactly represent your particular model.

1. Mark the cut-out area on the ceiling by tracing around the provided template.
2. Cut out the hole in the ceiling using a pad saw, then slide the C-Ring into the ceiling, aligning it over the cut-out hole.
3. Refer to page 15 for wiring and set-up instructions, then return to point 4 below.
4. Connect a secondary support line to the safety tab. Some construction codes require use of this secondary support point, which should connect to a separate secure support point using a suitable support line. Consult construction codes in your region.
5. Slide the speaker assembly through the hole and turn the screws to extend the mounting wings. Tighten the screws until a firm grip is achieved. If using a power driver, Tannoy recommends a torque setting of 1.5 Nm. DO NOT OVERTIGHTEN!
6. Insert grille by pushing it onto the speaker.

Installation Instructions for Optional Plaster Ring

An optional plaster (mud) ring bracket is available from Tannoy. This bracket is designed to be pre-installed into newly constructed, non-suspended ceilings.

Note: Speaker images are for guidance only and may not exactly represent your particular model.

1. Nail or screw the plaster ring to the joists.
2. Lay the speaker wiring to where the speaker will be fitted and complete the plastering work on the ceiling.
3. Cut out the hole in the ceiling using a pad saw.
4. Refer to page 15 for instructions on wiring, then return to point 5 below.
5. Connect a secondary support line to the safety tab. Some construction codes require use of this secondary support point, which should connect to a separate secure support point using a suitable support line. Consult construction codes in your region.
6. Slide the speaker assembly through the hole and turn the screws to extend the mounting wings. Tighten the screws until a firm grip is achieved. If using a power driver, Tannoy recommends a torque setting of 1.5 Nm. DO NOT OVERTIGHTEN!
7. Insert grille by pushing it onto the speaker.

Wiring and Setting Up

Note: Speaker images are for guidance only and may not exactly represent your particular model.

We recommend the use of insulated speaker wiring of between 12 and 18 AWG.

WARNING: The power to the amplifier must be turned OFF when making connections to the loudspeakers. All connections must be checked before turning the amplifiers.

1. Remove the wiring cover at the back of the speaker can to access the removeable Euro-type connector plug and socket.
2. The speakers come with a standard speaker cable clamp and an optional gland for EN5424 applications. (Note: EN5424 does not cover the CVS 801S and CVS801SLZ subwoofers.)
3. Feed the cable through and attach to the Euro-type connector.
4. For connection to an amplifier: Use Pins 1 and 2. Ensure correct wiring polarity: Pin 1 is positive, Pin 2 is negative.
5. For connection to additional speakers in a distributed line: Pins 3 and 4 are used to loop through to additional speakers. Ensure correct wiring polarity: Pin 3 is positive, Pin 4 is negative.

Diagram Description:

Figure 4 shows typical connections of two loudspeakers in a 70V distributed system, connecting to a 70V Power Amplifier.

Figure 5 shows typical connections of two loudspeakers in a stereo system, connecting to a Stereo Power Amplifier.

Tighten the cable clamp or cable gland and plug in the Euro-type connector to the loudspeaker. Replace the rear cover and securely tighten the supplied screws.

The speaker is fitted with a multi-tap transformer for use in distributed-line systems. There is also a LOZ tap. Select the required tap before pushing the grill in place. The average impedance of each speaker in this range is 8 Ohms in the LOZ setting.

CAUTION: THE SPEAKER IS SUPPLIED IN LOW IMPEDANCE MODE. NEVER CONNECT THE SPEAKER TO A 70/100 VOLT AMPLIFIER WHILE THE SPEAKER IS SET FOR LOW IMPEDANCE (LOZ).

Speaker Tap Selector Switches (Fig.6):

Diagrams show the tap selector for CVS 301, CVS 401, CVS 601, CVS 801, and CVS 801S. Each diagram displays multiple settings labeled 'LOZ', '70V', and various Wattage values (e.g., 100W, 80W, 60W, 50W, 30W, 25W, 20W, 15W, 7.5W, 6.3W, 3.8W, 1.9W). The LOZ setting is typically indicated as 8Ω.

Dimensions (mm)

Specifications

*1 Average power rating is under IEC-shaped pink noise with a 6dB crest factor for 100 hours continuously.

Other Important Information

1. Register online. Please register your new Music Tribe equipment right after you purchase it by visiting musictribe.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable.

2. Malfunction. Should your Music Tribe Authorized Reseller not be located in your vicinity, you may contact the Music Tribe Authorized Fulfiller for your country listed under “Support” at musictribe.com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at musictribe.com. Alternatively, please submit an online warranty claim at musictribe.com BEFORE returning the product.

Declaration of Conformity

Hereby, Music Tribe declares that this product is in compliance with Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC, and this passive product is not applicable to EMC Directive 2014/30/EU, LV Directive 2014/35/EU.

Full text of EU DoC is available at https://community.musictribe.com/

EU Representative: Music Tribe Brands DK A/S

Address: Ib Spang Olsens Gade 17, DK - 8200 Aarhus N, Denmark