Explore Industrial 3D Printing Solutions | Stratasys Additive PrintingTerms and Conditions of Sale
User Guide for stratasys models including: DOC-60019 Origin One Tray Pour Jig, DOC-60019, Origin One Tray Pour Jig, One Tray Pour Jig, Tray Pour Jig, Pour Jig, Jig
prieš 2 dienas — The Origin One Tray Pour Jig is designed to assist in cleaning the tray by allowing resin to be poured cleanly and efficiently into a material bottle.
File Info : application/pdf, 8 Pages, 525.68KB
DocumentDocumentOrigin OneTM Tray Pour Jig Installation and User Guide The Origin One Tray Pour Jig is designed to assist in cleaning the tray by allowing resin to be poured cleanly and efficiently into a material bottle. The Tray Pour Jig uses locating bumpers and a magnetic locking switch to hold the tray in place. A filter holder is designed to hold the 190um filter in place above the material bottle. Friction hinges make pouring the tray as easy as possible while preventing the tray from rotating backwards during operation. © Copyright 2023 Stratasys. All rights reserved. DOC-60019 Rev. A Origin OneTM Tray Pour Jig Installation and User Guide Assembly Assembly 1. Remove the Origin One tray pour jig handle, base, and filter holder from the shipping packaging. 2. Remove all wrapping material from the Origin One tray pour jig handle, base, and filter holder. 3. Attach the Origin One tray pour jig handle to the base using the two provided M6 hex screws and 5mm hex key. Tighten the hex screws until they are snug. See Figure 1. Figure 1: Attach handle to base 4. Attach the filter holder to the base by sliding the filter holder tabs into the slots in the tray pour jig base. © Copyright 2023 Stratasys. All rights reserved. Page 2 Origin OneTM Tray Pour Jig Installation and User Guide 5. Confirm the filter holder opening faces forward. See Figure 2. Figure 2: Attach filter holder to base Assembly Opening © Copyright 2023 Stratasys. All rights reserved. Page 3 Origin OneTM Tray Pour Jig Installation and User Guide Operation Operation 1. Place a filter into the filter holder. 2. Hook the two filter tabs onto the two filter holder posts as shown below. See Figure 3. Figure 3: Filter placement © Copyright 2023 Stratasys. All rights reserved. Page 4 Origin OneTM Tray Pour Jig Installation and User Guide Operation 3. Place the Origin One tray containing resin onto the Origin One tray pour jig platform. Confirm the corner of the tray aligns with the platform alignment tab as shown below. See Figure 4. Figure 4: Align the tray Alignment Tab 4. Attach the tray pour spout to the tray. 5. Place a resin receptacle under the resin filter. © Copyright 2023 Stratasys. All rights reserved. Page 5 Origin OneTM Tray Pour Jig Installation and User Guide Operation 6. Unlock the platform locking tab. This secures the tray to the platform and allows the platform to be raised. See Figure 5 (page 6) and Figure 6 (page 6). Figure 5: Platform locked Figure 6: Platform unlocked © Copyright 2023 Stratasys. All rights reserved. Page 6 Origin OneTM Tray Pour Jig Installation and User Guide Operation 7. Using the handle, slowly raise the tray to empty the resin from the tray, through the filter, and into the resin receptacle. See Figure 7 (page 7). Figure 7: Pour resin 8. When the resin has finished puring into the receptacle, lower the handle. © Copyright 2023 Stratasys. All rights reserved. Page 7 Origin OneTM Tray Pour Jig Installation and User Guide 9. Lock the platform locking tab. This will secure the platform and allow the tray to be removed. 10. Clean any remaining resin from the tray in accordance with manufacturers recommendations. www.stratasys.com c-support@stratasys.com © Copyright 2023 Stratasys. All rights reserved. DOC-60019 Rev. A Customer acknowledges the contents of this document and that Stratasys parts, materials, and supplies are subject to its standard terms and conditions, available on http://www.stratasys.com/legal/terms-and-conditions-of-sale, which are incorporated herein by reference. The specifications and/or information on which this document is based are subject to change without notice. Stratasys and Origin One are trademarks of Stratasys and/or subsidiaries or affiliates and may be registered in certain jurisdictions. All other product names and trademarks are the property of their respective owners. Page 8