VEVORVEVOR
Instruction Manual for VEVOR models including: L3030 Desktop Laser Engraver, L3030, Desktop Laser Engraver, Laser Engraver, Engraver
VEVOR VEVOR Laser Engraver 12.2"x11.8" Large Engraving Area 5.5W Laser Power | VEVOR EU
VEVOR Macchina per Incisione Laser, 410 x 400 mm Potenza 5,5 W 6000 mm/min in Lega di Alluminio per Carta, Legno, Pelle, Stoffa, Plastica, Acrilico, Superficie Metallica Verniciata : Amazon.it: Fai da te
File Info : application/pdf, 9 Pages, 3.97MB
DocumentDocumentL3030 Laser Engraving Machine Warning Strictly prohibit laser radiation of the eyes! Strictly prohibit watching laser without wearing protective glasses! Strictly prohibit using by children! Strictly prohibit using this machine unattended! Scan for assemble video 1/9 L3030 V1.0 1. Parts List Part No 01 Part Name Y1-axis component 3030 Parts List Explanation Already assembled 02 Y2-axis component Already assembled 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 L1 M1 M2 M3 C1 C2 C3 C4 C5 C6 C7 C8 L3030 V1.0 X-axis component Already assembled Aluminum profile (X) Aluminum profile (X) L-shaped connector 2020*430mm 2020*495mm L shape Laser connecting plate Already assembled Leg Fixed wire block A Fixed wire block B Synchronous belt Inner hexagon screw Inner hexagon screw Set screw Ship nut Square nut Manual nut ---- ---- ---- 2GTlength 510mm M5*8 M5*10 M5*6 M5-10 M5 M5 Control board package VIGO-28 Wiring harness and protective pipe ---- Power supply and power line 12V DC Inner Hexagon Wrench 4/2.5/2mm Nut Wrench 8# USB cable ---- Protective glass ---- non-slip mat ---- Cable ties ---- Line pressing plate Card reader Instruction manual Length 490mm ---- ---- Laser packageOptional Laser kit Optional Component for lifting bracket Already assembled Inner hexagon screw M3*8 Inner hexagon screw M3*6 Control board package18 Control board VIGO-28 Acrylic plate for control board A ---- Acrylic plate for control board B ---- Column 3*6 Inner hexagon screw M3×25 Nut M3 Key cap White Key cap Red 22//69 Quantity 1Set 1Set 1Set 2 1 4 1 4 1 1 1 10 3 10 5 10 4 1Set 1Set 1 1Set 1 1 1 1 6 1 1 1 1Set 1Set 4 4 1 1 1 8 4 4 2 1 Picture / / / / / / / 3030V1.0 2. Machine Assembly 01: Y1-axis component 1Set 02: Y2-axis component 1Set Connector component 4Set 16: Square nut M5 2PCS 01Y1-axis component Aluminum profile 2020*485mm 04: Aluminum profile 2020*430mm 16: Square nut M5 06: L-shaped connector 1PCS Y2-axis component 14: Set screw M5*6 2PCS Connector component 4Set 04: Aluminum profile 2020*430mm 2PCS Y1-axis component 16: Square nut M5 12: Screw M5*8 8PCS 08: Leg 4PCS Y2 Y1 Tall leg installation mode 3/9 3/6 Put synchronous belt into the square hole Short leg installation mode L33003300V1V.01.0 14Set screw M5*6 2PCS 03: X-axis component 1Set 05: Aluminum profile 2020*495mm 1PCS 16: Square nut M5 2PCS 11: Synchronous belt 510mm 1PCS 15: Ship nut M5-10 4PCS (Already assembled) 07: Laser connecting plate 1PCS 17: Manual nut M5 4PCS C3: Acrylic plate for control board B 1PCS C1: Control board 1PCS C8: Red key cap 1PCS C2: Acrylic plate for control board A 1PCS 13: Screw M5*10 2PCS 09: Fixed wire block A 1PCS 15: Ship nut M5-10 2PCS C6: Nut M3 4PCS C4: Column 3*6 8PCS C7: White key cap 2PCS C5: Screw M3*25 4PCS 13: Screw M5*10 1PCS 10: Fixed wire block B 1PCS 15: Ship nut M5-10 1PCS 3. Laser Installation M1: Component for lifting bracket 1Set 07: Laser connecting plate1PCS L1: Laser kit 1Set Weak light switch UP 17: Manual nut M5 4PCS M2: M3*8 4PCS M3: M3*6 4PCS L3030 V1.0 4/9 4/6 15: Ship nut M5-10 2PCS 18: Control board package 1Set 12: Screw M5*8 2PCS 3030V1.0 Up Down 4. Cable connection Laser 3P,1300mm laser wire through the hole. 2 pieces of cable tie. X-Stepper motor wire 4P-6P,1200mm Control board Y1 Y2 X 3P Stepper motor Laser The wire is stuck in hole B of the fixed wire block. 2. Install fixed wire block A 1.Collate wiring harness Y2-Stepper motor X -Stepper motor Y2 stepper motor wire along the aluminum profile slot and through the X component. Y1-Stepper motor Y1-Stepper motor wire 4P-6P,650mm 3. 3 pieces of cable tie. Y2-Stepper motor wire 4P-6P,1200mm 5/9 5/6 L3030 V1.0 3030V1.0 5. Download and run the engraving control software "VevorWorks" Open our website www.vevorengraver.com. Find the control software for L3030, then click to download it to your computer. Green software doesn't need to be installed. Decompress the file you downloaded just now. The software running OS is Win7 Win8 and Win10. Open the fold and double-click the VevorWorks.exe file to run the engraving software. The OS may prompt that the software will use the network, please click OK (some computer systems do not prompt, if the software cannot use the network, please allow it manually in the firewall setup). In addition, the L3030 also supports Wi-fi connection control engraving on smartphone or iPad. You can also install VevorWorks (For Andriod or iOS) on your phone or iPad to control the engraving machine. The following is the using of windows version software. The machine also supports the engraving software of the third-party standard GRBL, such as LaserGrbl, LightBurn, etc 6. Connect VevorWorks software and laser engraving machine Long press the power button on the machine panel to turn on it. There are three ways to connect engraving software and the machine. (1) USB-Serial Connection Connect the USB-Serial cable to both control board and computer. In general, Win10 can automatically identify the device. Win7 or other OS may need to install driver manually. Please double click ch341ser.exe to install the driver if necessary. Click Connect on top left corner of VevorWorks, SERIAL-ON will be displayed in the title bar, indicating that the connection is successful. (2) Machine establish Wi-Fi Hotspot Wireless Connection If the USB cable is connected, be sure to disconnect it. After the machine turned on, the blue signal light will double flash. It indicates that the machine has established the Wi-Fi hotspot named VIGO-ESPXXXX (Where "XXXX" is its name). Turn on the wireless network settings of the computer system, and choose to connect VIGO-ESPXXX with password 12345678. Click Connect on left up corner of VevorWorks. Users will be reminded finding device VIGO-ESPXXX, click OK to connect, and WLAN-ON will be displayed on the title bar, indicating that the connection is successful. Please note that users cannot visit internet in this mode. (3) Wireless LAN Connection You are recommended to place the machine and router in the same room when using this connection. The machine does not support 5G signal WLAN, so please send 2.4G signal SSID to control board. Usually use the SSID name without "5G". When VevorWorks has connected to the machine by hotspot, then click Settings; click the Network at the bottom left. Input the SSID (No 5G) and Password, and click Send. The control board will restart automatically after receive the account successfully. Please make sure to use the 2.4G WLAN for control board. After restart (generally 2-5s), the single flashing of the signal light indicates the successful access to WLAN. If the USB cable is connected, be sure to disconnect it. Reset the wireless network of the computer to join the same WLAN (It is ok for computer to use whether 2.4G or 5G signal). The title bar of VevorWorks will show the name of WLAN. Click Connect on VevorWorks. Users will be reminded that find device VIGO-ESPXXX, click OK to connect, and WLAN-ON will be displayed on the title bar, indicating that the connection is successful. Once the machine connected WLAN successfully, Please notice that the machine will connect to this WLAN firstly every time you start it in the future. If the connection fails, the machine will still establish the wireless hotspot VIGO-ESPXXX. If the connection fails, please check whether the 2.4G name and password you send are correct, and try again. 7. Adjust focus Please use the focal length measuring piece to adjust the module height so that the distance from the lower edge of the module protective cover to the engraved object is equal to the height of the measuring piece. 8. Open or input the engraving content and adjust the engraving parameters Engraving content can be opened at the top of the software image or gallery, or edit the engraving text. Set the start location of engraving and adjust the size of engraving. Select one of the engraving modes. There two engraving mode, line mode and point mode, which can respectively engrave black-and-white images, grayscale images and outlines. (only line engraving is supported for outline, please use outline when cutting objects.) Set engraving parameters. There are four engraving parameters that can be set. These parameters will affect the engraving speed and engraving effect. It is necessary for you to understand the function of these parameters and adjust them according to different engraving materials and contents. (1) Line engraving speed: Set the engraving speed (only valid for line engraving mode). Note that the set speed may not be reached when the image is too small or the dot distance is too dense. (2) Maximum laser power: Set the maximum laser power, which is the laser power when the maximum gray level (i.e. all black) in the dot matrix gray mode and line scan gray mode and the laser power in the Binary (black and white) engraving mode. The unit is the percentage of the installed laser full power. L3030 V1.0 6/9 (3) Engraving point distance: set the precision of dot matrix engraving or line scanning engraving, and the number of lines or points per millimeter. (4) Time of dot engraving: Set the engraving time of each dot. The unit is millisecond. According to the power of the laser module and engraving material, we generally recommend to set about 1ms to 5ms. 9. Preview the engraving range and start engraving Click Range preview to confirm the position and range of engraving. Click Start and wait for the engraving to be completed. In the wireless connection state, you can also click Upload File, and the engraving file will be uploaded to the SD card of the control board. You can use the offline engraving function provided by this machine to complete engraving. 10. Offline engraving Before using offline engraving, please make sure that the engraving file has been uploaded to the SD card of the control board (please refer to the file upload in the previous step, the upload function is only available in wireless connection). Press the Button A on the side panel of the machine to start the preview. During the preview progress, press the Button A to stop the preview. During preview, pressing Button B will immediately start engraving. When the system is idle or offline preview, press Button B to start engraving, press Button B again to pause engraving, and press Button B again to resume engraving. During engraving or pause, press and hold Button B to stop engraving. Note: When the wireless network signal is unstable or the computer is unstable, the uploading may fail. If the uploading engraving file fails, you can export the engraving file to the computer and copy it to the SD card, and then insert the SD card into the engraving machine for offline engraving. Please ensure that the file name exported and copied is SD_default.nc . 11. Introduction of software interface function 12. Scan the QR code to download VevorWorks App Scan QR code or open the URL to download Android or iOS App http://www.vevorengraver.com/L3030/download (Support) 7/9 L3030 V1.0 13. Control board panel Button Mode Function Remarks Boot up. Press and hold the button until you hear the sound of"Di"and the status Power Switch indicator starts to flash, then release the button. Long pressed Shut down. Press and hold the button until the status indicator goes off, then release the button. Power Switch When the power is on, a short press will turn the weak laser light on or off, so that you can Shot pressed adjust the focus when you are carving offline. BUTTON-A Pressed If system is idle, start the default file range preview in SD card. If the range preview for SD file is in progress, stop the preview immediately. BUTTON-A Pressed for 1 Restart the control board (Equivalent to turning off and turning on the power), users may second reconnect in WLAN connection mode. If system is idle or in range preview for SD file, start SD file engraving immediately. BUTTON-B Pressed If SD file is engraving, suspend engraving. If SD file engraving paused, continue engraving. BUTTON-B Pressed for 1 second If SD file is engraving or paused, stop engraving. If system is not working and gets error (LED: Long On and Short Off), clear error and set control board to normal. Pressed for 1 second means to press and hold the button, the indicator light will be on, and wait for one second, then the light will be off or return to other flashing state and then release the button. Status Indicator Light Status System Status Remarks Double Flash Hotspot Wireless VIGO-ESPXXXX is on. System is idle and ready to work. Normal Single Flash Local WLAN is connected. System is idle and ready to work. Normal Fast Double Flash System is working with Vigo Works connected. (SERIAL or WLAN ON) Normal Fast Triple Flash System is working with SD card file on. Normal Fast Single Flash Uploading file to SD card. Normal Double and Double Firmware upgrade is ongoing by OTA. Normal Long On and Short Off System alarm or abnormal working. Long press button B for clear alarm or Restart. Normal again after restart Long On Any button is being pressed. Normal Always Off LED failure or control board failure. Failure Please note that if system is working or uploading, any other operations on the control board will ignore. That is if system is working on SD file, any operations by Vigo Works will have no effect. Moreover, when system is working with Vigo Works connection, any button press will ignore except Restart. Please focus the laser on the materials referring to the laser instructions below before starting engraving. 13.1 Instructions for Lase Please wear the protective glasses before operating the laser! When all the connections are completed, turn on the power, and the laser is standby for working. The indicator light on the top of the laser is continuous lighting at this time. Turn on the weak light and adjust the focal length Please lay the materials to be carved flat under the laser. Please turn on the weak light in the engraving software or press the weak light switch on the top of the laser module. Then the red light will flash and the weak light on. Laser spots can be seen on the materials at this time. Adjust the height of the module, when the laser spots are smallest and clearest, it is the optimum state for laser engraving. Or use the focal length measuring piece to adjust the module height so that the distance from the lower edge of the module protective cover to the engraved object is equal to the height of the measuring piece. After that, press the weak light switch again, and the weak light is turned off. The red light on the top of the laser is continuous lighting at this time, and the laser is standby for working. It is important to understand that this weak light switch on the top of the laser module is not controlled by engraving control software. So be sure to switch back to normal (make sure that weak light is off) before you start engraving. L3030 V1.0 8/9 14. Notice and FAQ (1) The shape of all parts above in this description is only as a sign. There may be a difference between the actual parts and the parts in the installation instructions. Please refer to the shape of the actual parts purchased. (2) Please pay attention to the sequence of the installation steps to avoid repeated disassembly. (3) Make sure hibernate and sleep are disabled when working long hours. This feature may cause the laser to continue to glow out of control, and burning on the table. (4) It is strictly prohibited to use this machine unattended. (5) Make sure to wear protective glasses before operating the laser. The control software cannot be opened Wrong control responding The carving is not good or there is no burned trace The stepper motors are not working properly FAQ Please check whether the system is Win7 or above. Please power off the device and shut down the software, then restart both. If useless, please try below. Please restore the device by click Restore in setting, then click Model Select and choose the device you used to reset parameters. Please check whether the focal length of laser is in the recommended distance. Please check whether the laser focus is at a minimum. Please check whether the object to be caved is laid flat. Please check whether the laser is in weak light mode. Please check whether the power indicator light on the control panel is continuous lighting. Please check whether the motors are working properly. Please check whether the connection between the three motors and control board is correct. Please check for any irrelevant stuff on the slide to block movement. Please check whether the motor drive current is normal. Too little current causes the motors to stall. Too much current makes the motors to vibrate, and causes the movement of the machine or materials to be carved. Please check whether the power indicator light on the control panel is continuous lighting. 15. Update Our software will be updated continuously. Please visit our website: www.vevorengraver.com for more new products and software. Please be sure to download the VevorWorks for this machine. Please refer to the Software Installation Manual for control software instructions. Please contact us if you have any questions. Powered by VEVOR 2022 9/9 L3030 V1.0