User Manual for Prestel models including: SP-H2-14T150, SP-H2-14T150 HDMI 1x4 HDBaseT Splitter, HDMI 1x4 HDBaseT Splitter, HDBaseT Splitter, Splitter
Набор из (1) сплиттера HDMI 2.0 1:4 HDBaseT и (4) приемников, Prestel SP-H2-14T150
HDMI коммутаторы, разветвители, повторители Prestel SP-H2-14T150, цена: 137 038 руб - купить в Галерее безупречной электроники Назаров
File Info : application/pdf, 14 Pages, 2.30MB
DocumentDocumentPrestel SP-H2-14T150 18Gbps HDMI 1×4 HDBaseT Splitter USER MANUAL Thank you for purchasing this product For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. Surge protection device recommended This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lighting strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment. Table of Contents 1. Introduction........................................................................................... 1 2. Features................................................................................................. 1 3. Package Contents................................................................................1 4. Specifications....................................................................................... 2 5. Operation Controls and Functions...................................................... 3 5.1 Transmitter....................................................................................... 3 5.2 HDBaseT Receiver........................................................................... 5 5.3 IR Pin Definition................................................................................6 6. EDID Mode.............................................................................................7 7. ASCII Commands................................................................................. 8 8. Application Example............................................................................12 1. Introduction This 18Gbps HDMI 1x4 HDBaseT Splitter can distribute 1 source signal to any 4 display devices. Support video resolution up to 4K2K@60Hz 444. It is designed with 1 HDMI loop output and 4 HDBaseT outputs. The HDMI signal transmission distance can be extended up to 120 meters at the resolution of 4K2K@60Hz, or 150 meters at 1080P@60Hz via a single CAT6/ 6a/7 cable. The product supports IR and RS-232 signal pass-through, audio extract function and advanced EDID management. 2. Features HDMI 2.0b, HDCP 2.2 and HDCP 1.x compliant Support 18Gbps video bandwidth Support video resolution up to 4K2K@60Hz 444 Support HDR, HDR10+, HLG and Dolby vision Support up to 7.1CH HD audio pass-through Support digital and analog audio de-embedded output Extend the signal transmission distance up to 120 meters at the resolution of 4K2K@60Hz, 150 meters at 1080P@60Hz via a single CAT6/6a/7 cable Support 1 HDMI input, 1 HDMI loop output and 4 HDBaseT outputs. IR, RS-232 routed to HDBaseT output Advanced EDID management Support one-way POC function (only from transmitter to receiver) Compact design for easy and flexible installation 3. Package Contents 1 × 18Gbps HDMI 1×4 HDBaseT Splitter 4 × HDBaseT Receiver 5 × IR Blaster Cable (1.5 meters) 5 × 20K~60KHz IR Receiver Cable (1.5 meters) 5 × 3-pin Phoenix Connector 1 × 5-pin Phoenix Connector 10 × Mounting Ear 1 × 24V/2.7A DC Locking Power Adapter 1 × User Manual -1- 4. Specifications Technical HDMI Compliance HDCP Compliance Video Bandwidth HDMI 2.0b HDCP 2.2/1.x 594MHz/18Gbps Video Resolution Up to 4k2k@60Hz 4:4:4 Color Depth Color Space 8-bit,10-bit,12-bit(1080p@60Hz) 8-bit (4K2K@60Hz YUV4:4:4) 8-bit,10-bit,12-bit(4K2K@60Hz YCbCr 4:2:2/4:2:0) RGB 4:4:4, YCbCr 4:4:4 / 4:2:2 4:2:0 HDR Support HDR, HDR10+, HLG, Dolby vision LPCM 2.0/2.1/5.1/6.1/7.1, Dolby Digital, Dolby TrueHD, HDMI Audio Formats Dolby Digital Plus(DD+), DTS-ES, DTS HD Master, DTS HD-HRA, DTS-X Coaxial Audio Formats PCM2.0, Dolby Digital / Plus, DTS 2.0/5.1 Analog Audio Formats PCM 2.0CH ESD Protection Human body model--±8kV (Air-gap discharge) & ±4kV (Contact discharge) Connection Input Output Control 1×HDMI Type A (19-pin female) 1×HDMI Type A (19-pin female 4x HDBaseT OUT [RJ45] 1x Coaxial Audio OUT [RCA] 1x L/R Audio OUT [5-pin phoenix connector] 1×RS-232 (3-pin phoenix connector 1x EDID DIP switch [5-pin] 1x IR IN [3.5mm Stereo Mini-jack] 1x IR OUT [3.5mm Stereo Mini-jack] -2- Mechanical Housing Silkscreen Color Dimensions Weight Power Supply Power Consumption Operation Temperature Storage Temperature Relative Humidity Metal Enclosure Black Transmitter: 220mm (W) × 130mm (D) × 40mm (H) Receiver: 140mm (W) × 65mm (D) × 18mm (H) Transmitter: 853g Receiver: 246g Input: AC100 - 240V 50/60Hz, Output: DC 24V/2.7A (US/EU standards, CE/FCC/UL certified) 35W 0°C ~ 40°C / 32°F ~ 104°F -20°C ~ 60°C / -4°F ~ 140°F 20~90% RH (non-condensing) 5. Operation Controls and Functions 5.1 Transmitter Front Panel 18Gbps HDMI 1x4 HDBaseT Splitter IN LOOP 1 2 3 4 OUT 1 23 4 No. Name Function Description 1 POWER LED When the device is powered on, the red power LED will be on. 2 IN LED When the HDMI IN port connects an active source device, the green LED will be on. 3 LOOP LED When the HDMI LOOP OUT port connects an active display device, the green LED will be on. 4 OUT(1~4) LED When the H1D/5BT OUTPUT port connects an HDBaseT Re3ceiv4er, the corresponding green OUT LED will be on. -3- Rear Panel 1 23 4 5 TX RX RS-232 1 0 EDID IN OUT AUDIO OUT IR 1 IN LOOP OUT HDMI 2 HDBT OUTPUT 3 ON OFF 4 DC 24V 6 7 8 9 10 11 No. Name Function Description 1 RS-232 Connect to a PC or control system via a 3-pin phoenix connector cable for three functions: 1, Firmware update; 2, Control the Splitter via RS-232 commands; 3, RS-232 signal pass-through (from transmitter to receiver or from receiver to transmitter). 2 IR IN Connect to IR receiver cable, the IR receive signal will emit to "IR OUT" port of the HDBaseT Receiver. 3 IR OUT Connect to IR blaster cable, the IR emit signal is from "IR IN" port of the HDBaseT Receiver. 4 AUDIO OUT Coaxial/balanced audio output port, connect to amplifier or (COAX, L/R) speaker. 5 POWER switch Press this switch to power on/off the device. 6 EDID DIP switch Used to set EDID mode. Please refer to Section "6. EDID MINo:3dHeD" M4foIrindpeutat iplso.rt, connect to HDMI source device such 7 HDMI port as DVD or set-top box with an HDMI cable. LOOP OUT: HDMI loop output port, connect to the HDMI display device such as TV or Monitor with an HDMI cable. 8 HDBT OUTPUT Connect to the HDBT IN port of the HDBaseT receiver port (1~4) with a CAT cable. Illuminating: Transmitter and Receiver are in good Connection connection status. 9 Signal Indicator Flashing: Transmitter and Receiver are in poor lamp (Green) connection status. Dark: Transmitter and Receiver are not connected. -4- Data Signal Illuminating: HDMI signal with HDCP. 10 Indicator lamp Flashing: HDMI signal without HDCP. (Orange) Dark: No HDMI signal. 11 DC 24V Plug the DC 24V power supply into the unit and connect the adaptor to an AC outlet. (Note: The transmitter can power the receiver via a CAT cable.) 5.2 HDBaseT Receiver SERVICE 1 2 DC 24V HDBT IN HDMI OUT AUDIO OUT IR IN IR OUT 3 546 7 8 9 10 11 No. Name Function Description 1 When the receiver is powered on, the power indicator will Power Indicator be on. 2 SERVICE port Used for firmware update. Plug DC 24V/1A power supply into the unit and connect 3 DC 24V the adapter to an AC outlet. (Note: The HDBaseT receiver also can be powered by the transmitter via a CAT cable.) 4 HDBT IN Connect to the HDBT OUTPUT port on the transmitter with a CAT cable. Illuminating: Transmitter and Receiver are in good Connection connection status. 5 Signal Indicator Flashing: Transmitter and Receiver are in poor lamp (Green) connection status. Dark: Transmitter and Receiver are not connected. Data Signal Illuminating: HDMI signal with HDCP. 6 Indicator lamp Flashing: HDMI signal without HDCP. (Orange) Dark: No HDMI signal. 7 HDMI OUT HDMI output port, connect to HDMI display device such as TV or Projector with an HDMI cable. -5- 8 AUDIO OUT 9 IR IN 10 IR OUT 11 RS-232 Audio output port, connect to amplifer or speaker. Connect to the IR Receiver cable. The IR signal will send to the IR OUT port of the transmitter. Connect to the IR blaster cable, the IR signal is from IR IN port of the transmitter. 3-pin Phoenix connector for RS-232 command transmission. The RS-232 command will pass-through from transmitter to receiver or from receiver to transmitter. 5.3 IR Pin Definition IR Receiver IR Blaster IR Blaster IR Blaster Signal Power NC IR Receiver IR Signal Power Grounding Note: When the angle between the IR receiver and the remote control is ± 45 °, the transmission distance is 0-5 meters; when the angle between the IR receiver and the remote control is ± 90 °, the transmission distance is 0-8 meters. -6- 6. EDID Mode The defined EDID setting list of the product is shown as below: EDID Mode EDID Description 11111 1080P, Stereo Audio 2.0 11110 1080P, Dolby/DTS 5.1 11101 1080P, HD Audio 7.1 11100 1080I, Stereo Audio 2.0 11011 1080I, Dolby/DTS 5.1 11010 1080I, HD Audio 7.1 11001 1080P 3D, Stereo Audio 2.0 11000 1080P 3D, Dolby/DTS 5.1 10111 1080P 3D, HD Audio 7.1 10110 4K2K30Hz_444, Stereo Audio 2.0 10101 4K2K30Hz_444, Dolby/DTS 5.1 10100 4K2K30Hz_444, HD Audio 7.1 10011 4K2K60Hz_420, Stereo Audio 2.0 10010 4K2K60Hz_420, Dolby/DTS 5.1 10001 4K2K60Hz_420, HD Audio 7.1 10000 4K2K60Hz_444, Stereo Audio 2.0 01111 4K2K60Hz_444, Dolby/DTS 5.1 01110 4K2K60Hz_444, HD Audio 7.1 01101 4K2K60Hz_444, Stereo Audio 2.0 HDR 01100 4K2K60Hz_444, Dolby/DTS 5.1 HDR 01011 4K2K60Hz_444, HD Audio 7.1HDR 01010 COPY_FROM_LOOP OUT 01001 01000 COPY_FROM_HDBT OUT1 COPY_FROM_HDBT OUT2 00111 COPY_FROM_HDBT OUT3 00110 COPY_FROM_HDBT OUT4 00101 1080P, Stereo Audio 2.0 00100 1080P, Stereo Audio 2.0 00011 1080P, Stereo Audio 2.0 00010 1080P, Stereo Audio 2.0 00001 1080P, Stereo Audio 2.0 00000 PC control mode -7- 7. ASCII Commands The product also supports ASCII command control. Connect the RS-232 port of the product to a PC with a 3-pin phoenix connector cable. Then, open a Serial Command tool on PC to send ASCII commands to control the product. The ASCII command list about the product is shown as below. ASCII Commands Serial port protocol. Baud rate: 115200, Data bits: 8bit, Stop bits:1, Check bit: 0 x - Parameter 1 y - Parameter 2 ! - Delimiter Command Code Power Function Description Example s power z! r power! Power on/off the device,z=0~1 (z=0 power off, z=1 power on) s power 1! Get current power state r power! s reboot! Reboot the device s reboot! System Setup help! List all commands help! Feedback Default Setting Power on System Initializing... power on Initialization Finished! FW version x.xx.xx power on/power off Reboot... System Initializing... Initialization Finished! FW version x.xx.xx r status! r fw version! r link in! r link out y! s reset! Get device current status r status! Get Firmware version r fw version! Get the connection status of r link in! the input port Get the connection status of the y output port y=0~5(0=all, r link out 1! 1~4=HDBT 1~4 5 = loop out) Reset to factory defaults s reset! -8- Get the unit all status: power, in/out connection, edid mode MCU BOOT: Vx.xx.xx MCU APP: Vx.xx.xx HDMI IN: connect hdmi loop out: connect hdbt output 1: connect Reset to factory defaults System Initializing... Initialization Finished! FW version x.xx.xx Command Code Function Description Example Feedback Default Setting Output Setting Set hdmi loop output stream s hdmi stream z! on/off z=0~1(0:disable,1:enable) Enable hdmi loop out s hdmi stream 1 ! stream Disable hdmi loop out enable stream s hdmi hdcp z! s hdbt y hdcp z! Set hdmi loop output hdcp on/ off s hdmi hdcp 1! z=0~1(0:disable,1:enable) Enable hdmi loop out hdcp enable Disable hdmi loop out hdcp Enable hdbt output 1 hdcp Set hdbt output y hdcp on/off, s hdbt 1 hdcp 1 ! Disable hdbt output 1 y=0~4(0=all) z=0~1(0:disable, hdcp enable 1:enable) Enable hdbt all s hdbt 0 hdcp 1 ! outputs hdcp Disable hdbt all outputs hdcp Set hdbt output y stream on/ s hdbt y stream z! off, y=0~4(0=all) z=0~1 (0:disable,1:enable) s hdbt 1 stream 1 ! s hdbt 0 stream 1 ! Enable hdbt output 1 stream Disable hdbt output 1 stream Enable hdbt all enable outputs stream Disable hdbt all outputs stream r hdmi stream! Get hdmi loop out stream status r hdmi stream! Enable hdmi output stream r hdmi hdcp! r hdbt y hdcp! Get hdmi loop out hdcp status r hdmi hdcp! Get hdbt output y hdcp status, y=0~4(0=all) r hdbt 1 hdcp! Enable hdmi output hdcp Enable hdbt output 1 hdcp r hdbt stream! Get hdbt output y stream status, y=0~4(0=all) r hdbt 1 stream! Enable hdbt output 1 stream -9- Command Code Function Description Example Feedback Default Setting EDID Setting Set input EDID from default EDID z, z=1~27 1 1080p,Stereo Audio 2.0 2 1080p,Dolby/DTS 5.1 3 1080p,HD Audio 7.1 4 1080i,Stereo Audio 2.0 5 1080i,Dolby/DTS 5.1 6 1080i,HD Audio 7.1 7 3D,Stereo Audio 2.0 8 3D,Dolby/DTS 5.1 9 3D,HD Audio 7.1 10 4K2K30_444, Stereo Audio 2.0 11 4K2K30_444,Dolby/DTS 5.1 12 4K2K30_444,HD Audio 7.1 input EDID:1080p, 13 4K2K60_420, Stereo Audio 2.0 Stereo Audio 2.0 s edid in from z! 14 4K2K60_420, Dolby/DTS 5.1 s edid in from 1! 15 4K2K60_420,HD Audio 7.1 16 4K2K60_444, Please toggle EDID Stereo Audio 2.0 dip switch to 00000! 17 4K2K60_444, Dolby/DTS 5.1 18 4K2K60_444,HD Audio 7.1 19 4K2K60_444, Stereo Audio 2.0 HDR 20 4K2K60_444, Dolby/DTS 5.1 HDR 21 4K2K60_444, HD Audio 7.1 HDR 22 copy from hdmi loop out 23 copy from hdbt output 1 24 copy from hdbt output 2 25 copy from hdbt output 3 26 copy from hdbt output 4 27 use user1 EDID 1080p,Stereo Audio 2.0 s edid user1 00 FF FF FF FF ...! Set user1 EDID data s edid user1 00 user1 EDID data: 00 ff ff ff ff .... ! FF FF .... r edid user1! Get user1 EDID data r edid user1! user1 EDID data : 00 FF FF FF FF FF FF 00 ......... r edid in! Get EDID status of the input r edid in! input EDID: 4K2K60_ 444,Stereo Audio 2.0 r edid in data! Get the EDID data of the hdmi r edid in data! input EDID data : 00 FF FF FF FF FF FF 00 ...... -10- Command Code Function Description Example Feedback Default Setting RS-232 BYPASS Setting Set RS-232 port connect to RS-232 connect to s rs232 bypass hdbt y! HDBT out1 Receiver RS-232 s rs232 bypass port y=0~5( 0=all, hdbt 1! HDBT OUT1 RS-232 not connect y=0 1~4= hdbt out 1~4 5=NC) to HDBT OUT Get RS-232 port connect to r rs232 bypass! HDBT out receiver RS-232 port s device baud w size x stop y parity z! Set receiver control device COM port setting w=2400, 4800,9600,19200,38400, 57600,115200, x=7,8 y=1,2, z=none, even,odd RS-232 connect to HDBT OUT1 r rs232 bypass! RS-232 connect to all HDBT OUT RS-232 not connect to HDBT OUT s device baud 57600 size 8 stop 1 parity none! receiver device COM port setting baudrate: 57600 data size :8, stop:1 parity: none s rs232 time x! set send RS232 command wait time x=200~5000ms s rs232 time 200! send RS-232 command wait time 200ms 200ms -11- 8. Application Example IR Receiver Amplifier IR Blaster PC 2.0 Speakers TX RX RS-232 1 0 EDID IN OUT AUDIO OUT IR 1 IN LOOP OUT LAN HDMI Transmitter 2 HDBT OUTPUT 3 ON OFF 4 DC 24V UHDTV DVD or Blu-ray Player DC 24V HDBT IN LAN Cat 6/6a/7 Receiver Power Supply HDMI OUT AUDIO OUT IR IN IR OUT UHDTV 2.0 Speakers IR Receiver HDMI Matrix with RS-232 function IR Blaster -12-Adobe PDF library 10.01