Instruction Manual for SEHLORAN models including: Double Drawer Dresser for Bedroom with 7 Drawers, Double, Drawer Dresser for Bedroom with 7 Drawers, Bedroom with 7 Drawers, 7 Drawers
Sehloran Double Drawer Dresser for Bedroom with 7 Drawers, Tall Dessers Storage Tower, Chests of Drawers, Removable Fabric Bins, Dresser Organizers Unit for Closets, Hallway, Entryway, Wood Top, Gray : Home & Kitchen
7-Drawer Fabric Storage Organizer A1 x 4 Left/Right bottom tube Tubo inferior izquierdo/derecho B1 x 2 Middle bottom tube Tubo de fondo medio A2 x 2 Left middle tube Tubo central izquierdo B2 x 2 Middle tube Tubo medio A3 x 1 Left top frame Marco superior izquierdo A4 x 1 Right top frame Marco superior derecho B3 x 1 Middle top frame Marco superior medio C x 4 Tube Tubo D1 x 1 Long wood shelf Estante largo de madera D2 x 1 Short wood shelf Estante de madera corto E1 x 7 Drawer bottom Fondo del cajón E2 x 7 Drawer Cajón F x 10 Connecter Conector G x 6 Leveling feet Pies de nivelación H x 12 Short bolt Perno corto I x 4 Long bolt Perno largo J x 3 Screw Tornillo K x 3 Anchor Ancla L x 1 Wrench Llave inglesa M x 1 X-frame marco X N x 2 Double-threaded bolt Perno de doble rosca 1/8 O x 7 Left slide Diapositiva izquierda P x 7 Right slide Diapositiva derecha The product picture below is just for tube and frame's position reference only, but missing important details. Do read the following steps for details to avoid mistakes and re-work. La imagen del producto a continuación es solo para referencia de posición del tubo y el marco, pero faltan detalles importantes. Lea los siguientes pasos para obtener detalles para evitar errores y reelaboración. D1 A3 B3 D2 M A4 A2 B2 A2 B2 A1 A1 C C B1 B1 C C A1 A1 2/8 Step 1 Using connecter "F" to connect frame "A1" & "A2 & "A3". Punch tight gradually by plastic hammer (not provided), until "A1" & "A2" & "A3" connect firmly. Paso 1 Usando el conector "F" para conectar el marco "A1" y "A2 y "A3". Golpee gradualmente con un martillo de plástico (no incluido), hasta que "A1" y "A2" y "A3" se conecten firmemente. A3 F A2 A2 F NOTICE! A1 Make sure the gourd A1 hole heads up as above. ¡AVISO! Asegúrate de que el agujero de la calabaza esté arriba como arriba. 3/8 Step 2 Using connecter "F" to connect frame "B1" & "B2" & "B3". Punch tight gradually by plastic hammer (not provided), until "B1" & "B2" & "B3" connect firmly. Paso 2 Usando el conector "F" para conectar el marco "B1" y "B2 y "B3". Golpee gradualmente con un martillo de plástico (no incluido), hasta que "B1" y "B2" y "B3" se conecten firmemente. B3 F B2 B2 F NOTICE! Make sure the gourd hole heads up as above, and small round hole in correct position as above. B1 ¡AVISO! B1 Asegúrese de que el orificio de la calabaza esté hacia arriba como se indica arriba y que el orificio redondo pequeño esté en la posición correcta como se indicó anteriormente. 4/8 Step 3 Using short bolt "H" to attach X frame "M" to "A2" "A3" & "B2" "B3", tighten with wrench"L". Paso 3 Usando el perno corto "H" para unir el marco X "M" a "A2" "A3" y "B2" "B3", apriete con la llave "L". H B2 B3 H M L A3 B1 A2 L A1 H M A3 Step 4 Using double-threaded bolt "N" & bolt "I" to attach tube "C" to "A1" & "B1", Using bolt "H" to attach "B3" & "A3" to top shelf "D1", tighten with wrench"L". Paso 4 Usando el perno de rosca doble "N" y el perno "I" para unir el tubo "C" a "A1" y "B1", usando el perno "H" para unir "B3" y "A3" al estante superior "D1", apriete con llave "L". N B1 D1 H B3 C H B1 N C A1 I N C I 5/8 H A3 A3 D1 H Step 5 Using connecter "F" to connect frame "A1" & "A4". Punch tight gradually by plastic hammer (not provided), until "A1" & "A4" connect firmly. Paso 5 Usando el conector "F" para conectar el marco "A1" y "A4". Golpee gradualmente con un martillo de plástico (no incluido), hasta que "A1" y "A4" se conecten firmemente. A4 F A1 A1 Step 6 Using bolt "I" and double-threaded bolt "N" to attach tube "C" to "A1" & "B1", then using bolt"H" to attach "B3"& A4" to top shelf "D2".tighten with wrench"L". Paso 6 Usando el perno "I" y el perno de rosca doble "N" para unir el tubo "C" a "A1" y "B1", luego use el perno "H" para unir "B3" y A4" al estante superior "D2". Apriete con llave "L". B1 N C C D2 B3 H H A4 C C B1 B1 N C C A1 A1 I 6/8 Step 7 Screw the leveling feet "G" as shown. Paso 7 Atornille las patas niveladoras "G" como se muestra. A1 B1 A1 A1 B1 A1 A1 G G G G Step 8 Assemble the slide "O" & "P" into the frame as shown. Paso 8 Ensamble la corredera "O" y "P" en el marco como se muestra. O P O P O P O P Left slide Diapositiva izquierda Right slide Diapositiva derecha O P O P Insert the knot into the hole. Inserta el nudo en el agujero. O P O P 7/8 Step 9 Using "J" & "K" to attach the whole frame to the wall as shown. Paso 9 Usando "J" y "K" para unir todo el marco a la pared como se muestra. K J K J K J Caution! The product must be secured to the wall. Precaución! El producto debe fijarse a la pared. Step 10 Put drawer bottom "E1" into drawer "E2", and place drawer into the the frame. Paso 10 Coloque la parte inferior del cajón "E1" en el cajón "E2" y coloque el cajón en el marco. Step 11 Completed. Paso 11 Completa. E1 E2 88.5cm K J 77cm 30cm 8/8Adobe PDF library 15.00 Adobe Illustrator 24.3 (Windows)