KMC Controls | Building Automation and Control SolutionsSimplyVAV: Installation & Setup – KMC Controls
User Guide for SimplyVAV models including: BAC-8000 Controllers, BAC-8000, Controllers
1 day ago — Quick start guide for installing SimplyVAV controllers. 1 Align the damper and drive hub. Manually rotate the damper on the VAV box to the fully.
Quick start guide for installing SimplyVAV controllers. 1 Align the damper and drive hub. Manually rotate the damper on the VAV box to the fully.
File Info : application/pdf, 2 Pages, 623.08KB
DocumentDocumentQuick start guide for installing SimplyVAV controllers These are brief instructions for installing a SimplyVAV controller. To view a short video of this procedure, or to download a PDF of The Simply VAV Application and Installation Guide, browse to the SimplyVAV page of the KMC Controls website. 1 Align the damper and drive hub Manually rotate the damper on the VAV box to the fully open position. Press the gear clutch button and rotate the drive hub in the same direction that opened the damper. Turn the hub until it reaches a stop. 2 Mount the controller to the VAV box. Place the controller over the damper shaft. Finger tighten the nuts on the V-bolt to position the shaft in the drive hub. Center the mounting bushing in the mounting tab and fasten it with a #8 sheet metal screw. Evenly tighten the V-bolt nuts on the drive hub to 30-35 in-lbs. 3 Connect the room sensor cable Connect a SimplyVAV sensor to the controller with a standard Ethernet cable. Plug the controller end of the cable into the T'stat connector. 4 Connect the airflow sensors Connect the airflow sensor on the VAV box to the airflow ports on the controller. Use 0.25 in. FR tubing. 5 Connect auxiliary equipment (optional) Other VAV equipment such as fans, heaters, reheat valves, and discharge air temperature sensors connect at the green terminals. If the controller is part of a BACnet network, wire it to the gray MS/TP network terminals. 6 Connect 24 volt power Connect the controller to a 24 volt, Class 2 transformer at the black power terminals. As soon as power is connected, the controller begins operation. Drive hub and V-bolt Gray network terminals Airflow sensor ports Black power terminals Gear clutch button T'stat connector Mounting tab and bushing Green terminals for fan, reheat and other equipment Quick start configuration guide for SimplyVAV controllers Use an STE-8001 or STE-8201 sensor to configure the Simply VAV controller. If another type of sensor is installed as the room sensor, temporarily connect an STE-8001 as a service tool. To get started: Press together the up and down buttons to start configuration or balancing. Enter Password 2 if required. New installations do not have a password. Press the up and down buttons to move between functions or change values. Press the setpoint button to choose a selection or save a value. Optional Configuration End configuration Temp. setpoints Cool Setpoint Heat Setpoint Occupied Cooling Occupied Heating Unoccupied Cooling Unoccupied Heating Changeover Differential Standby Differential Setpoints and limits Advanced Restore End configuration BACnet instance Primary Secondary End configuration Primary K Factor Min, Cool Flow Set Password 1 English/Metric BACnet MAC Measured Max. Flow Measured Max. Flow Secondary K Factor Max. Cool Flow Set Password 2 Baud Rate Measured Min. Flow Measured Min. Flow No/Stg/Par Auxillary airflow Override timer No/Ser/Par Min. Heat Flow Standby timer CCW/CW Max. Heat Flow Discharge Air Temp Min. Fan Speed (%) MAXF Max. Fan Speed (%) Auto. Occ. Mode Calibration CNFG The main configuration parameters for the VAV terminal unit. COMM Set BACnet device instance, MAC address, and network baud. BLNC Set airflow balancing parameters. Only the PRI (primary) menu is used for single duct VAV. STPT Enter temperature setpoints and limits. BOX Set up reheat, fan operation, and basic terminal unit functions. FLOW Set airflow setpoints and limits. ADVC Enter passwords and enable model specific features. RSTR Restore to factory settings. For complete details on controller configuration, browse to Dual Minimum CFM the SimplyVAV page of the KMC Controls website and download a PDF of the SimplyVAV Application and I.nstallation Guide. * Not used for all models ** Select English (factory setting) or Metric before setting other parameters. © 2022 KMC Controls, Inc. 915-019-04C