PLT COLOR SELECTABLE 5" & 6" LED SURFACE MOUNT DOWNLIGHT FIXTURE

WARNING

• Installation, service, and maintenance of luminaries should be performed by a qualified licensed electrician.
• Before starting installation, please read instructions and keep for future reference.
• This fixture is designed for use in a circuit protected by a fuse or circuit breaker.
• To avoid electrical shock, do not turn on fixture with missing or damaged lens.
• There are no serviceable parts inside of the LED module.

CAUTION

• Power wires connecting the fixture must be rated for a minimum of 90°C (194°F).
• Do not make or alter any holes in the wiring enclosure, or in any of the electrical components.
• This fixture is rated TYPE NON-IC and is not suitable for direct contact with insulation.
• Do not cover the fixture with any heat insulated materials.
• The National Electric Code (NEC) does not permit cords to be concealed where damage to the cord's insulation may go unnoticed. To prevent fire damage, do not run cord behind walls, ceilings, soffits, or cabinets where it may be inaccessible for examination. Cords should be visually examined periodically and immediately replaced when damage is noted.
• All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use parts that are worn out or broken. Failure to obey this instruction could invalidate the ETL certification.

NOTICE

• Suitable for use in wet locations.
• Account for small parts and destroy packing material, as these may be hazardous to children.

Package Contents

Diagram shows parts labeled A through G. Part A is a round LED disc. Part B represents two torsion springs. Part C is an E26 base whip with wires. Part D shows three wire nuts. Part E shows two mounting screws. Part F shows two metal mounting brackets. Part G shows two small screws.

Preparation

• Before beginning assembly, installation, or operation of product, make sure all parts are present.
• Tools Required for Assembly (not included): Ladder, safety glasses
• Estimated assembly time: 15-20 minutes per fixture

Installation Instructions

New Construction to 4" Junction Box

Step 1

For 4" junction box installation, attach the mounting brackets (F) to the junction box using the two mounting screws (E).

Step 2

Pull out the source wires from the outlet box. Make wire connections to fixture (A) using wire nuts (D): black to black, white to white, and ground to ground. Carefully push the wires back into the outlet box.

Step 3

Align the springs on the back of the fixture with the slots on the mounting bracket (F). Push the fixture upwards until the springs engage with the mounting brackets (F) and the fixture is flush with the ceiling.

Diagram 1 shows mounting brackets (F) being attached to a junction box with screws (E).

Diagram 2 illustrates wire connections using wire nuts (D): black wire to black wire, white wire to white wire, and ground wire to ground. Wires are then pushed back into the outlet box.

Diagram 3 shows the fixture being pushed upwards, with the torsion springs (B) engaging with the mounting brackets (F) to secure the fixture flush with the ceiling.

Retrofit Installation to 5"-6" Recessed Housing

Step 1

For 5"-6" recessed housing installation, secure the torsion springs (B) to the mounting brackets (F) using the spring holder screws (G). Then, connect the mounting brackets (F) to the back of the disc light (A) by snapping into place.

Step 2

Connect the E26 base whip (C) to the fixture (A), making connections using wire nuts (D): black to black and white to white. Cap the ground wire using a wire nut. Then, connect the E26 base whip (C) to the socket inside of the recessed housing by screwing it into the socket.

Step 3

Squeeze the torsion springs (B) together and install into torsion spring brackets inside of the recessed housing while pushing the fixture into the recessed housing. Gently pull to ensure the fixture is secure and firmly in place.

Diagram 1 shows torsion springs (B) secured to mounting brackets (F) with screws (G), and the mounting brackets (F) attached to the fixture (A).

Diagram 2 illustrates connecting the E26 base whip (C) to the fixture (A) with wire nuts (D), and then screwing the whip (C) into the socket of the recessed housing.

Diagram 3 shows the torsion springs (B) being squeezed and inserted into the recessed housing brackets, with the fixture (A) being pushed into place and secured.

Troubleshooting

The light does not illuminate

• With power supply turned off, ensure all connections are made correctly.
• Make sure the circuit breaker is on and that switch controlling branch circuit is on.
• If the fixture still does not illuminate, call a certified electrician.

Dimming

• This product is suitable for use in dimming circuits. For 10%-100% light control, use with an LED-compatible dimmer (sold separately), including:
• LUTRON SCL-153P, LUTRON CTCL-153P
• LUTRON DVCL-153P, LUTRON MACL-153M

Care and Maintenance

• Only use a mild soap and/or water with a soft cloth to clean the fixture. Harsh chemicals will damage the fixture. Do not wipe the fixture with a rough cloth as that may scratch the finish or the lens.