RF Controlled RGBCCT LED Flood Light

Important Information

Please read all instructions prior to installation.

Safety and Notes

• Do not use with wall dimmers, relays, or any other controls other than those listed.
• Avoid looking directly into the lamp when illuminated.
• Ensure all mounts are securely attached and will support the weight of the fixture. Failure to properly support the fixture may result in damage or injury, for which the manufacturer does not assume responsibility.
• The supplied cable on 100-240 VAC models utilizes a 5-15P plug compatible with standard 120 VAC outlets only.
• Lights can display an RGB color or a white CCT value, but cannot do both simultaneously.

Specifications

Check product label for specific electrical specifications related to installation. Improper installation will void warranty.

Optional Compatible Remotes and Controller

One of these controls (available at additional cost) is required to operate the light. Each light can be linked with up to four different controls (any combination of wireless remotes and Wi-Fi controls). Each control (and zone) can be linked to an unlimited number of lights.

RGBCCT-MZ8-RF (for use with RGBCCT models)

1. Master On/Off: Acts as a master ON ▶ / OFF ⚫ control for all paired lights. If a single zone is currently active, pressing the master ON ▶ button on remote or back button in app restores master function.
2. Color Selection Ring: Directly selects color along a circular spectrum. For white light, press W button in app or Zone On 1️⃣ button on remote until light changes to a steady bright white.
3. Selection LED Indicator: Flashes once to indicate when a command has been selected.
4. Brightness Touch Slider - Increase/Decrease: Increases (right side) or decreases (left side) the brightness level. Changing active mode resets brightness level to full.
5. Mode: Preset modes feature different color combinations, light transitions, and patterns. On wireless remote, this button initiates mode function and scrolls through modes in ascending order. In app, simply select mode button and press any numbered mode button to switch between modes.
6. Mode Speed Increase/Decrease: Increases (S+ or +Speed) or decreases (S- or -Speed) speed of currently active mode.
7. Zone On/Off: Allows zones (channels) of RGBW lights to be separately linked and controlled by remote / app. Pressing one of the Zone On 1️⃣ buttons activates that zone. Commands will affect only lights in that zone. Once linked to a zone, lights remain linked until they are unlinked.
8. Saturation Touch Slider - Increase/Decrease: Cools (right side) or warms (left side) CCT value.
9. White LED Selection: Switches to white LED operation.

WIFI-CON2 (for smart phone / tablet control, for use with all models)

Functions are similar, but the phone/tablet display will vary in appearance from remote.

Optional WiFi-CON2 Setup

Begin by downloading the MiBoxer app on a compatible device (iOS or Android). Refer to the WIFI-CON manual for complete instructions on establishing connection with a phone or tablet.

A constant 2.4 GHz Wi-Fi connection to both your device and the WIFI-CON2 is required for remote access.

Linking a Light

1. Press the Link/Unlink button in the app.
2. Select the desired zone.
3. Follow the on-screen instructions to link the light.

Activating and Controlling a Specific Zone

To activate a specific zone, select one of the available zones and press the On button. The zone is now active, and remote commands will only affect lights linked to that zone until returned to master mode.

Unlinking a Light

Make certain the light is powered off before beginning.

1. Press the Link/Unlink button in the app.
2. Select the desired zone.
3. Press the unlink button to remove all lights from the selected zone.

Optional Remote Control Setup

Begin by installing two AAA batteries (not included) into the wireless remote. The wireless remote operates using 2.4 GHz RF frequency and has a 98.4 ft. (30 m) range.

Linking a Light

1. Ensure the light is powered off.
2. Apply power to the light. Within 3 seconds, press and hold one of the Zone On 1️⃣ buttons until the light begins flashing. The light will flash 3 times if successfully linked to the selected zone.

Activating and Controlling a Specific Zone

To activate a specific zone, press the Zone On 1️⃣ button for the desired zone. The zone is now active, and remote commands will only affect lights linked to that zone until returned to master mode.

Unlinking a Light

1. Ensure the light is powered off.
2. For RGBCCT-MZ8-RF: Apply power and within 3 seconds, press the Zone On 1️⃣ or Master On ▶ button five times quickly.

With either remote, the light will flash 10 times if successfully unlinked.

Preset Modes