Wireless Dust Control Remote and Adapter

Important Safety Instructions

WARNING: READ ALL SAFETY WARNINGS, INSTRUCTIONS, ILLUSTRATIONS AND SPECIFICATIONS PROVIDED WITH THIS POWER TOOL. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. SAVE THESE INSTRUCTIONS.

• Do not modify the plug.
• Chemical Burn Hazard. Keep coin cell battery away from children.
• Power tool plugs must match the outlet. Unmodified plugs and matching outlets will reduce risk of electric shock.
• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators.
• Do not expose power tools to rain or wet conditions.
• When operating outdoors, use an extension cord suitable for outdoor use.
• If operating in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply.

Symbology

• [Read Manual]
• [Pairing]
• [Power]
• [Power Indicator]
• [Chemical Burn Hazard]
• [Fuse Failure]
• [cULus Listed]

Specifications

Functional Description

Adapter (Cat. No. 0950-20)

• Male plug (not shown)
• [Pairing Button] (2)
• [Power Indicator] (3)
• [Outlet] (Female Plug) (6)
• [Pairing Indicator] (7)

Remote (Cat. No. 0951-20)

• [Pairing Button] (4)
• [Power Button] (5)

Assembly

Pairing

If the remote is not connected to the adapter, pairing can be set up by:

1. Insert the Adapter into an outlet. The power indicator will light for 1 second to confirm power.
2. Press the button on the Adapter and the remote until both LEDs begin to flash. A steady green light on both the Adapter and remote confirms pairing.

Note: The remote needs to be within close proximity for signal reception. This procedure times out in 30 seconds if not paired.

Multiple remotes can be paired to one adapter.

Unpairing

1. Press and hold the remote button until its LED shows a flashing red light.
2. Press and hold the adapter button until its pairing indicator LED shows a flashing red light.

This procedure times out in 30 seconds if not paired.

Remote Strap Installation

Follow these steps to install the remote strap:

1. Feed the logo side of the strap through the inner side of the remote housing.
2. Fold the strap over and press firmly.
3. Feed the tail end of the strap through the outer side of the remote housing.
4. Fold the strap over and press firmly.

To adjust the strap length, release the velcro and pull snug.

Remote Belt Clip

To remove the belt clip:

1. Remove the screw from the back of the remote.
2. Pull the belt clip away from the remote.

To install the belt clip:

1. Line up the tabs on the clip with the notches on the back of the remote.
2. Insert the screw and tighten securely.

General Use and Care

Use proper tools rated for this device. Others may be hazardous.

1. Insert the Adapter into a wall outlet. Confirm the power indicator flashes and the pairing indicator is lit.
2. Plug the corded tool into the Adapter outlet.

NOTICE: Do not use with a tool that requires input current greater than 12 A. This will result in damage to the adapter.

3. Using the remote, press the power button to turn the tool ON/OFF.

Note: Ensure the tool being used is ON and fully operational.

Maintenance

Internal Remote Battery

WARNING: Chemical Burn Hazard. This device contains a lithium button/coin cell battery. A new or used battery can cause severe internal burns and lead to death in as little as 2 hours if swallowed or enters the body. Always secure the battery cover. If it does not close securely, stop using the device, remove the batteries, and keep it away from children. If you think batteries may have been swallowed or entered the body, seek immediate medical attention.

An internal battery is used on the remote for full functionality. To replace the battery:

1. Remove the strap or the screw on the belt clip.
2. Remove the screw and open the battery door.
3. Remove the old battery, keep it away from children, and dispose of it properly.
4. Insert the new battery (3V CR2032), with the positive side facing up.
5. Close the battery door and tighten the screw securely.
6. Reattach the strap or screw with belt clip.

Internal Fuse Failure

Please contact 1-800-SAWDUST or visit milwaukeetool.com for service.

Accessories

WARNING: Use only recommended accessories. Others may be hazardous.

For a complete listing of accessories, go online to www.milwaukeetool.com or contact a distributor.

Wireless Communication

Pursuant to part 15.21 of the FCC Rules, you are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the product.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules and ISED-Canada's license exempt RSS standards. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.

Service Information

United States

Milwaukee Tool
1-800-SAWDUST (1.800.729.3878)
Monday-Friday, 7:00 AM - 6:30 PM CST
Visit: www.milwaukeetool.com

Contact Corporate After Sales Service Technical Support with technical, service/repair, or warranty questions.

Email: metproductsupport@milwaukeetool.com

Become a Heavy Duty Club Member at www.milwaukeetool.com to receive important notifications regarding your tool purchases.

Canada

Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
Visit: www.milwaukeetool.ca

Mexico

CENTRO DE ATENCION A CLIENTES Techtronic Industries Mexico, S.A. de C.V.
Av. Presidente Masarik 29 Piso 7
11560 Polanco V Seccion
Miguel Hidalgo, Distrito Federal, México
01 (800) 030-7777 or (55) 4160-3540
Monday-Friday (9am to 6pm)
Visit: www.milwaukeetool.com.mx