User Guide for McIntosh models including: HR085 Remote Control, HR085, Remote Control, Control
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 www.mcintoshlabs.com HR085 Learning Guide
File Info : application/pdf, 6 Pages, 4.18MB
DocumentDocumentHR085 Learning Guide McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 www.mcintoshlabs.com Introduction The HR085 Remote Control is supplied with McIntosh Preamplifiers, Integrated Amplifiers and Tuners. The HR085 Remote Control has the ability to learn and store Remote Control (RC) Commands from three non-McIntosh Components. The RC Commands stored in the HR085 can be accessed by using the "DEVICE" Push-button together with the LED Indica- tors to select one of the three (TV, CABLE or AUX). Refer to figure 1 and the instructions starting on page 3 on "How to Learn and Store Commands". LED DEVICE indicators Push-button Number 1 Push-button Number 2 Push-button SELECT Push-button Figure 1 2 Remote Control Codes The HR085 Remote Control has been factory con- figured for the "Normal" McIntosh Control Codes used with most models. There is a set of "Alternate" McIntosh Control Codes for the HR085 Remote Con- trol. "This Alternate Control Code" is to be used when there are two McIntosh Models (A/V Control Center, Integrated Amplifier or Preamplifier) in the same location at the same time. This will prevent the HR085 Remote Control from adversely affecting the opera- tion of the units. Refer to figure 1 when performing the steps below. Note: Refer to the "Setup" Section of the Owner's Manual supplied with the A/V Control Center, Integrated Amplifier and/or Preamplifier for ad- ditional information about using the "Alternate Control Codes". To change the HR085 from "Normal" to "Alternate" Control Codes perform the following steps: 1. To change from the "Normal" to "Alternate" Control Codes, press and hold the SELECT and number 2 Push-buttons simultaneously (for about 8 seconds) until the Device Select LED flashes twice. 2. Referring to the SETUP Steps outlined in the McIntosh Model Owner's Manual, change one of the two Models over to the "Alternate" Codes. 3. Press the VOLume Up/ Down Push-button on the Remote Control to verify proper operation using the Alternate Codes. To change the HR085 from "Alternate" to "Normal" Control Codes perform the following steps: 1. To change from the "Alternate" to "Normal" Control Codes, press hold the SELECT and number 1 Push-buttons simultaneously (for about 8 seconds) until the Device Select LED flashes once. 2. Refering to the SETUP Steps outlined in the McIntosh Model Owner's Manual change one of the two Model over to the "Normal" Codes. 3. Press the VOLume Up/ Down Push-button on the Remote Control to verify proper operation using the Normal Codes. Technical Assistance If at any time you have questions about your McIntosh product, contact your McIntosh Dealer who is familiar with your McIntosh equipment and any other brands that may be part of your system. If you or your Dealer wish additional help concerning a suspected problem, you can receive technical assistance for all McIntosh products at: McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903 Phone: 607-723-3512 Fax: 607-724-0549 Table of Contents Introduction................................................................ 2 Remote Control Codes .............................................. 2 Technical Assistance.................................................. 2 Table of Contents ....................................................... 2 Preliminary Step ........................................................ 3 Signal Strength Test .................................................. 3 Learning Commands .................................................. 3 Delete Learned Commands ........................................ 4 Reset the HR085 to Default Settings .......................... 4 HR085 HEX Code Table..........................................4-5 Copyright 2015 © by McIntosh Laboratory, Inc. How to use the HR085 Learning Capabilities Preliminary Step A successful learning process requires adequate IR Signal Strength, both sending and receiving, from the McIntosh HR085 and the other Brand Remote Control. Please make sure the Remote Controls have fresh batteries installed and functioning correctly with their respective component(s) before proceeding. Signal Strength Test First perform the following test with the HR085 Re- mote Control and other Brand Remote Control before attempting to have the HR085 learn commands from them. 1. Referring to figure 2, position the remote controls as illustrated. HR085 IR Signal Send/Receive Other Brand Remote Locations 2-5cm Figure 2 2. The HR085 IR sensor must be receiving an adequate IR signal for the learning process to be successful. 3. Press and hold in the DEVICE Push-button for about 4 seconds, and the LED will flash twice. This indicates the HR085 Remote Control is in the Programming Mode. Immediately press the following number Push-buttons: 9, 1, 0, 0 4. Press and hold in one of the Push-buttons on the "Other Brand Remote". 5. One or more of the DEVICE LEDs on the HR085 will illuminate (the four LEDs function like a signal strength meter). Change the position of the HR085 or the other brand remote control, to illuminate as many of the four LEDs as possible. After the optimum position has been determined, do not move either remote control until learning process has been completed. 6. Press the DEVICE Push-button to exit the Programming Mode and proceed to "Learning Commands". Learning Commands All of the Push-buttons on the HR085 Remote Control except for the DEVICE Push-button, may be used to store RC Commands. Before proceeding make sure the Remote Controls have fresh batteries installed and the optimum position has been determined. In the following example, the (Play) and the : (Next) transport commands will be learned from the Other Brand Remote and stored in the HR085 Remote Con- trol "AUX" DEVICE. Refer to figure 3 and perform the following steps: Note: It is important to perform the learning/storing steps at a moderate pace, thus preventing drop- ping out of the Programming Mode. 1. Press and hold in the DEVICE Push-button for about 4 seconds, the LED will flash twice. 2. Using the Numeric Push-buttons on the HR085, enter in the Programming Code for the selecting the device (TV, CABLE or AUX) in which the learned commands will be stored, enter 3004: Note: The AUX Device will be using in this example. DEVICE NAME CODE NUMBER TV 1004 CABLE 2004 AUX 3004 3. The AUX LED will flash twice, followed by all four LEDS illuminating. 4. On the HR085, press and release the (Play) Push-button and three LEDs (TV, CABLE or AUX) will be illuminated. 5. Then press and hold in the (Play) Push- button on the Other Brand Remote until the TV and CABLE LEDs extinguish and just the AUX LED will be illuminated momentarily. 6. All four LEDs will illuminate on the HR085 Remote Control indicating it is now ready to learn an additional command(s). 7. Repeat steps four and five, except this time press the : (Next) Push-button in place of the (Play) Push- button. 8. When the AUX LED illuminates, quickly press the DEVICE Push- button until the AUX LED flashes twice. This will store the two learned commands (Play) and the : (Next). 9. The HR085 Remote Control returns to nor- mal operation. By pressing the DEVICE twice (AUX LED will illuminated) and the newly learned Other Brand Figure 3 transport commands can sent. 3 Delete Learned Commands If at any time it becomes desirable to remove previous- ly learned commands for a given Device (TV, CABLE or AUX) perform the following the steps below: 1. Press and hold in the DEVICE Push-button for about 4 seconds, the LED will flash twice. 2. Using the Numeric Push-buttons on the HR085, enter in the Code Number for the selected device (TV, CABLE or AUX). This will remove the stored commands for the device. In this example, the commands previously store for the AUX Device will be deleted by entering code number 3009: DEVICE NAME CODE NUMBER TV 1009 CABLE 2009 AUX 3009 The DEVICE AUX LED will flash twice indicating the stored commands have been deleted. Reset the HR085 to default Settings To remove all previously made changes to the DE- VICE settings ,TV, CABLE and AUX perform the following the steps below: 1. Press and hold in the DEVICE Push-button for about 4 seconds, the LED will flash twice. 2. Using the Numeric Push-buttons on the HR085, enter in the Code Number 9999. The LED will flash twice. 4 HR085 Hex Code Table Before implementing the procedures below, it is important to make sure the HR085 in the McIntosh Mode: 1. Press and hold in the DEVICE Push-button for about 4 seconds, the LED will flash twice. The following HR085 information (and the table on the next page) is intended to be used by McIntosh Dealers and Professional A/V Custom Installers. While most McIntosh models utilize the "Normal" Remote Control Codes, a few models utilize the "Al- ternate" Remote Control Codes. To change the HR085 from "Normal (page 1)" to "Alternate (page 2)" Control Codes perform the following step: 1. Press and hold the SELECT and number 2 Push- buttons simultaneously (for about 8 seconds) until the Device Select LED flashes twice. To change the HR085 back to the Normal Control Codes perform the following step: 2. Press and hold the SELECT and number 1 Push- buttons simultaneously (for about 8 seconds) until the Device Select LED flashes twice. The HR085 Remote Control has stored into its memory additional special Control Codes used in previous McIntosh Remote Controls. These stored Control Codes can be used for the purpose of learning the commands for programming other Remote Control(s) and/or Remote Control Systems. For example, to learn the Control Code for selection of the "DVD" Input on the HR070/071 Remote Controls using the "Normal Control Codes" perform the following steps: Note: Refer to the top row of information on the chart on the next page to select "Remote Control Model" and "Normal" or "Alternate" Code by entering the "Page _ number" in the steps. 1. Press and hold the SELECT and number 3 Push- buttons simultaneously (for about 8 seconds) until the Device Select LED flashes twice. 2. To learn the "DVD" Input Command press the numeric keypad "8" to send out the IR Command to select the DVD Input. To change the HR085 back to the Normal Control Codes perform the following step: 2. Press and hold the SELECT and number 1 Push- buttons simultaneously (for about 8 seconds) until the Device Select LED flashes twice. How to use the HR085 Remote Control HR085 Remote Control Normal Codes Alternate Codes HR070/71 Normal Codes Alternate Codes HR072 Normal Codes Alternate Codes HR073 Normal Codes Alternate Codes (Page 1) (Page 2) Additional Codes (Page 3) (Page 4) Additional Codes (Page 5) (Page 6) Additional Codes (Page 7) (Page 8) Code # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 PUSH-BUTTON PLAY NEXT BACK STOP TRIM PRESET LEFT UP RIGHT DOWN SELECT VOLUME UP (Note 1) VOLUME DOWN (Note 1) LEVEL UP LEVEL DOWN MUTE (Note 1) MODE BLUE BTN (SETUP) 42 43 RECORD 44 POWER ON 45 - 46 - 47 INPUT UP (Note 1) 48 INPUT DOWN (Note 1) 49 1 50 2 HEX CODES 00H 80H 01H 81H 02H 82H 03H 83H 04H 84H 05H 85H 06H 86H 07H 87H 08H 88H 09H 89H 0AH 8AH 0BH 8BH 0CH 0DH 0EH 0FH 10H 11H 8CH 8DH 8EH 8FH 90H 91H 12H 92H 13H 93H 14H 94H 15H 16H 17H 18H 19H 1AH 1BH 1CH 1DH 1EH 1FH 40H 41H 95H 96H 97H 98H 99H 9AH 9BH 9CH 9DH 9EH 9FH C0H C1H 42H C2H 43H C3H 44H C4H 45H C5H 46H C6H 47H C7H 48H C8H 49H 4AH 4BH 4CH 4DH 4EH C9H CAH CBH CCH CDH CEH 4FH CFH 50H D0H 51H D1H PUSH-BUTTON 1 -(ACC "ON") 2-(ACC "OFF") 3-(PAUSE) 4-(SAT) 5-(TV) 6-(SERVER) 7-(DVR) 8-(DVD) 9-(CD) SETUP-(CD2) 0-(TUNER) PWROFF-(REC) AM-(AUX) INFO-(INFO) GUIDE-(DISP) MENU-(MENU) HEX CODES 05H 85H 06H 86H 07H 87H 08H 88H 09H 89H 0AH 8AH 0BH 8BH 0DH 8DH 10H 90H 11H 91H 12H 92H 13H 93H 17H 97H 1DH 9DH 1EH 9EH 1FH 9FH PUSH-BUTTON 1 -(ACC "ON") 2-(ACC "OFF") 3-(PAUSE) 4-(SERVER) 5-(DVD) 6-(CD) 7-(CD2) 8-(TUNER) 9-(D/A) SETUP-(MM) 0-(MC) PWROFF-(AUX) INFO-(INFO) GUIDE-(DISP) MENU-(MENU) AM-(REC MONITOR) HEX CODES PUSH-BUTTON HEX CODES 05H 85H 1 -(ACC "ON") 05H 85H 06H 86H 2-(ACC "OFF") 06H 86H 07H 87H 3-(PAUSE) 07H 87H 4-(CDR) 08H 88H 5-(SERVER) 09H 89H 0AH 8AH 6-(MM) 0AH 8AH 7-(INPUT DOWN) 0BH 8BH 8-(INPUT UP) 0CH 8CH 0DH 8DH 9-(MC) 0DH 8DH 10H 90H SETUP-(CD) 10H 90H 11H 91H 0-(DVD) 11H 91H 12H 92H PWROFF-(TUNER) 12H 92H AM-(D/A) 13H 93H PRESET-(REC 14H 94H MONITOR) 14H 94H 15H 95H 16H 96H 17H 97H FM-(AUX Note 1) 17H 97H 1DH 9DH INFO-(INFO) 1DH 9DH 1EH 9EH GUIDE-(DISP) 1EH 9EH 1FH 9FH MENU-(MENU) 1FH 9FH 49H C9H Note 1: Punch through to Mcintosh key definition and function 5 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 www.mcintoshlabs.com The continuous improvement of its products is the policy of McIntosh Laboratory Incorporated who reserve the right to improve design without notice. Printed in the U.S.A. McIntosh Part No. 04161301Adobe InDesign CS5.5 (7.5.3) Adobe PDF Library 9.9