Havit Lighting
Instruction Manual for HAVIT Lightning models including: HV3277T-BLK-12V, HV3277T-WHT-12V, HV3277T-BLK-12V Virsma Step Light, HV3277T-BLK-12V, Virsma Step Light, Step Light, Light
Virsma LED Step Light Round Tri-Colour in Black/White - The Lighting Outlet
File Info : application/pdf, 2 Pages, 323.81KB
DocumentDocumentVirsma Step Light Installation Instructions Model No. Name Material Colour IP Rating Input Voltage Lamp Base Lamp Wattage Colour Temp Lumens CRI Wiring Dimmable Warranty Product Specifications HV3277T-BLK-12V Virsma Aluminium Black IP54 12v DC Built in LED 1x 4w TRI Colour - 3000k, 4000k, 5500k 110lm, 115lm, 120lm > 80 Parallel No 2 Years Replacement* HV3277T-WHT-12V White Dimensions Mounting Base Diagram 11 55 17 Ø145 2x Ø5 17 Ø13 40 30 55 Important Safety Issues: · This product must be installed by a qualified electrician according to AS/NZS 3000. · Ensure all electrical mains are disconnected before any installation. · Do not exceed maximum wattage restrictions for globes: 240V GU10 = 35w / 12V MR16 = 20w · Modification of this product will void any warranty. · Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system. · When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided. · Aluminium and 304SS fittings must not be installed within 2km of any salt water environments. · When installing copper fittings, gloves must be worn to avoid any oils transferring to fitting. · All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining) · All o-rings and seals must be in place correctly to maintain warranty. · These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions. Steps for Installation: 1. Make sure that the electrical circuit is free of voltage (master switch off ) 2. Loosen allen screws on side of fitting and remove face and set aside. 3. Install base plate to wall in desired location 4. Using an appropriate 12v DC LED Driver - DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V 5. Connect the cable - If more than one fitting installed, wiring must be done in parallel. 6. Fitting is preset to 3000k, to change slide switch to desired colour temperature 7. Reattach face to base plate making sure allen screws are tight to avoid water penetration 8. Apply silicon around edge of fitting to prevent any water from getting inside to electrical connections. 9. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit. Contact Details: 143 Beauchamp Road Matraville NSW 2036 Australia Must be installed by a licensed electrician Warranty Terms & Conditions* Additional Information Tel: 02 9381 8300 Fax: 02 9666 8881 Email: sales@havit.com.au Web: www.havit.com.au HV3277T-BLK-12V HV3277T-WHT-12V Virsma Step Light Installation Instructions Model No. Name Material Colour IP Rating Input Voltage Lamp Base Lamp Wattage Colour Temp Lumens CRI Wiring Dimmable Warranty Product Specifications HV3277T-BLK-240V Virsma Aluminium Black IP54 240v AC Built in LED 1x 4w TRI Colour - 3000k, 4000k, 5500k 110lm, 115lm, 120lm > 80 Parallel No 2 Years Replacement* HV3277T-WHT-240V White Dimensions Mounting Base Diagram 11 55 17 Ø145 2x Ø5 17 Ø13 40 30 55 Important Safety Issues: · This product must be installed by a qualified electrician according to AS/NZS 3000. · Ensure all electrical mains are disconnected before any installation. · Modification of this product will void any warranty. · Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system. · When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required, if not within this allowance warranty will be voided. · Aluminium and 304SS fittings must not be installed within 2km of any salt water environments. · When installing copper fittings, gloves must be worn to avoid any oils transferring to fitting. · All 316 & 304 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining) · All o-rings and seals must be in place correctly to maintain warranty · This form may be updated at any time due to product improvements, please check online installation form for most current version. Steps for Installation: 1. Make sure that the electrical circuit is free of voltage (master switch off ) 2. Loosen allen screws on side of fitting and remove face and set aside. 3. Install base plate to wall in desired location 4. Connect the cable - use wire with earth; connect the earth first, then live and neutral wire 5. Fitting is preset to 3000k, to change slide switch to desired colour temperature 6. Reattach face to base plate making sure allen screws are tight to avoid water penetration 7. Apply silicon around edge of fitting to prevent any water from getting inside to electrical connections. 8. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit. Contact Details: 143 Beauchamp Road Matraville NSW 2036 Australia Must be installed by a licensed electrician Warranty Terms & Conditions* Additional Information Tel: 02 9381 8300 Fax: 02 9666 8881 Email: sales@havit.com.au Web: www.havit.com.au HV3277T-BLK-240V HV3277T-WHT-240V