Instruction Manual for TARAMPS models including: T100.1 HF Passive Speaker, T100.1 HF, Passive Speaker, Speaker
Taramps | WARRANTY & REPAIR CENTERS
Instruction manual T 100.1 HF 50W RMS - 100W MUSICALS The installation of this product must be made by a qualified professional. T 100.1 HF PASSIVE BOX WITH 1 SPEAKER - 4 OR 8 OHMS The T 100.1 HF Passive Speaker was designed to achieve excellent precision in audio reproduc on. Thanks to its wide frequency response (80Hz to 22KHz), it guarantees accurate and natural audio reproduc on throughout its en re opera ng range. ENGLISH Technical parameters RMS power___________________________________ 50 W Musical power_________________________________ 100 W Nominal impedance_____________________________ 4 or 8 Ohms Sensitivity (@1W, 1m)-Free-Air____________________ 89 dB Finishing_____________________________________ Painting LACA/PU Frequency response (-6 dB)_______________________ 80 Hz to 22 KHz Resonance frequency___________________________ 120 Hz Weight without packaging________________________ 2.53 kg (5.57 lb) Dimensions (WxHxD)____________________________ 145x212x180 mm Acoustic components____________________________ 1 speaker 4'' Cabinet______________________________________ MDF 15mm Grid finish_____________________________________ Electrostatic painting Colors_______________________________________ White or black Recommended frequency cutoff HPF -12 dB octave___ 110 Hz Product dimensions 180 mm (7.09 in) 145 mm (5.71 in) 212 mm (8.35 in) Package content ·01 (one) T 100.1 HF acoustic box; ·01 (one) Fixing support; Response curves x impedance 4 Ohms 100 dBSPL SPL vs Freq 90 80 70 60 50 40 50 Hz 100 200 500 1K 2K Response curve an anechoic chamber, 1W / 1M. 5K 10K Ohm 10 9 8 7 6 5 4 3 20K 30K Response curves x impedance 8 Ohms 100 dBSPL SPL vs Freq 90 80 70 60 50 40 50 Hz 100 200 500 1K 2K Response curve an anechoic chamber, 1W / 1M. 5K 10K Ohm 40 30 20 10 9 8 7 6 20K 30K NOTE: Features, specifications and aesthetic aspects are subject to change without prior notice. Manufactured by: TARAMPS ELECTRONICS LTDA - TAX ID: 11.273.485/0001-03 - KM 30 Júlio Budisk Hwy, Da pedreira Neighborhood, Alfredo Marcondes, SP - 19180-000, Brasil - Made in Brazil SUPPORT Mounting bracket Installation with fixing bracket 3 1 2 1st STEP Choose the best location in your box and screw part 1. (Use the 2 screws that come with the support). Image 1; Part 2 Part 1 Part 3 2nd STEP Position piece 2 over piece 3 with the toothed washer between them; Insert the fixing screw together with the washers as shown in image 2; Position the nut and lightly tighten it. Toothed washer. Image 2; Toothed washer. Part 2 Image 3; Part 3 3rd STEP Part 1 Fix piece 3 to the wall; Position the set ``piece 1 + box'' between piece 2 with the toothed washer between them; Insert the fixing screw together with the washers as shown in image 3; Position the nut and lightly tighten it; Adjust the angle as desired and tighten the nuts and bolts, using a wrench. mouth or cannon to facilitate tightening. Attention: Avoid excessive tightening. Illustrative Images NOTE: Features, specifications and aesthetic aspects are subject to change without prior notice. Manufactured by: TARAMPS ELECTRONICS LTDA - TAX ID: 11.273.485/0001-03 - KM 30 Júlio Bidisk Hwy, Da pedreira Neighborhood, Alfredo Marcondes, SP - 19180-000, Brasil - Made in BrazilCorel PDF Engine Version 21.2.0.706