9 pagine
Sleek Collection - Solar Shades for Windows | SelectBlinds.com
INSTALLATION INSTRUCTIONS Open Roll Lifestyle Solar Shades Motorized Deco Fascia Important: Prior to installing the shade, pair the remote using the instructions included with the remote. Do not set the upper and lower limits until the shade is installed. Motorized with Open Roll 1. Install the Brackets 2. Install the Shade OB IB Secure the roller shade installation brackets with the supplied screws. If shade was ordered as outside mount (OB), attach the supplied screw covers on to the bracket for a finished look. 3. Install the Bracket Covers (if applicable) Click 1 Spring loaded pin end 2 Motor Side 1 INSTALLATION INSTRUCTIONS Motorized with Deco Fascia 1. Install the Fascia Brackets 2. Install the Brackets IB OB OB IB Outside mount (OB) requires a T-Bracket installation. Space brackets evenly. Note: Do not attach the Deco Fascia until the shade has been installed. Secure the roller shade installation brackets with the supplied screws. If shade was ordered as outside mount (OB), attach the supplied screw covers on to the bracket for a finished look. 3. Install the Shade 4. Install the Deco Fascia 1 2 3 1 Spring loaded pin end Inside Mount (IB) 1 2 3 2 Motor Side Outside Mount (OB) 5. Install the Returns (Optional) Metal returns (Outside mount only) include a plastic corner connector. Plastic returns (Inside mount with Outside Mounted fascia) snap on the end of the fascia. 2 Initial Set-up 1. Pair / Unpair Remote Control a. Press "P1" button (about 2 sec) on the motor head until Action on a. motor jog x1 and beep x1. Motor b. In the next 10 secs, press and hold "Stop" button on the Motor Response remote control until motor jog x2 and beep x3. * Repeat the same procedure to unpair remote control. Action on b. Remote Control Motor Response P1 Jog x1 Beep x1 Stop Jog x2 Beep x3 2. Change Motor Direction (if necessary) Press "Up" or "Down" button to check if the shade moves in the desired direction. If you need to reverse the direction, press and hold (about 2 sec) "Up" and "Down" buttons simultaneously until motor jog x1 and beep x1. Action on Remote Control Motor Response *The operation is only valid when there are no limits. If the motor has already set the upper and lower limit, then you can only switch direction by pressing P1 button (See P1 button instructions). + Up Jog x1 Down Beep x1 3. Setting the Upper and Lower Limits Set Upper Limit a. Press "Up" button to raise the shade, then press "Stop" button when it is in the desired upper limit. b. Press and hold (about 5 sec) "Up" and "Stop" buttons simultaneously until motor jog x2 and beep x3. Action on Remote Control Motor Response a. Up b. + Up Stop Jog x2 Beep x3 Set Lower Limit a. Press "Down" button to lower the shade, then press "Stop" button when it is in the desired lower limit. b. Press and hold (about 5 sec) "Down" and "Stop" buttons simultaneously until motor jog x2 and beep x3. Action on Remote Control Motor Response *If you exit the limit setting status before you finish the limit settings, the motor will take the previous existing limits. a. Down b. + Down Stop Jog x2 Beep x3 1 TM REMOTE | PROGRAMMING GUIDE Adjust Limits 1. Adjust the Upper Limit a. Press and hold (about 5 sec) "Up" and "Stop" buttons simultaneously until motor jog x1 and beep x1. b. Use "Up" button to raise the shade to the desired highest position, and use "Up" or "Down" button to do the final adjustment if necessary. c. Press and hold (about 5 sec) "Up" and "Stop" buttons simultaneously until motor jog x2 and beep x3. Action on Remote Control Motor Response Action on Remote Control Motor Response a. + Up Jog x1 c. + Up Jog x2 Stop Beep x1 Stop Beep x3 b. Up 2. Adjust the Lower Limit a. Press and hold (about 5 sec) "Down" and "Stop" buttons simultaneously until motor jog x1 and beep x1. b. Use "Down" button to lower the shade to the desired lowest position, and use "Up" or "Down" button to do the final adjustment if necessary. c. Press and hold (about 5 sec) "Down" and "Stop" buttons simultaneously until motor jog x2 and beep x3. Action on Remote Control Motor Response Action on Remote Control Motor Response a. + Down Jog x1 c. + Down Jog x2 Stop Beep x1 Stop Beep x3 b. Down 2 TM REMOTE | PROGRAMMING GUIDE Favorite Position 1. Set Favorite Position a. Use "Up" or "Down" button to move the shade to desired Favorite position. b. Press one "P2" button on the back of remote control until motor jog x1 and beep x1. Action on Remote Control Motor Response c. Press "Stop" button until motor jog x1 and beep x1. Action on Remote Control d. Once more, press "Stop" button until motor jog x2 and beep x3. Motor Response a. Up or Down or c. Stop Jog x1 Beep x1 b. P2 Jog x1 Beep x1 d. Stop Jog x2 Beep x3 2. Send Shade to Favorite Position Action on Remote Control Stop Press and hold (about 2 sec) "Stop" button, motor will move to Favorite position. Shade Response or 3. Delete Favorite Position a. Press one "P2" button until motor jog and beep x1. Action on a. Remote Control b. Press "Stop" button until motor jog and beep x1. Motor Response c. Once more, press "Stop" button until motor jog x1 and long beep x1. Action on c. Remote Control P2 Jog x1 Beep x1 Stop Motor Response Jog x1 Beep x1 b. Stop Jog x1 Beep x1 3 TM REMOTE | PROGRAMMING GUIDE Add or Remove Additional Remote 1. Using Current Remote Control Action on a. Remote Control a. On the current remote control, press one "P2" button until motor jog x1 and beep x1. b. Once more, on the current remote control, press one "P2" button until motor jog x1 and beep x1. Motor Response Action on c. c. On the New remote control, press one "P2" button until Remote Control motor jog x2 and beep x3. *Repeat the same procedure to remove additional remote control. Motor Response Current Remote Control P2 Jog x1 Beep x1 New Remote Control P2 Jog x2 Beep x3 2. New Remote Control Follow instructions on page 8 under the section Pair / Unpair Remote Control b. Current Remote Control P2 Jog x1 Beep x1 Adjust Motor Speed 1. Acceleration Speed a. Press one "P2" button until motor jog x1 and beep x1. b. Press "Up" button until motor jog x1 and beep x1. c. Once more, press "Up" button until motor jog x2 and beep x1. Action on a. Remote Control Motor Response Action on c. Remote Control Motor Response P2 Jog x1 Beep x1 Up Jog x2 Beep x1 2. Deceleration Speed Action on a. Remote Control a. Press one "P2" button until motor jog x1 and beep x1. b. Press "Down" button until motor jog x1 and beep x1. Motor Response c. Once more, press "Down" button until motor jog x2 and beep x1. Action on c. Remote Control *If the motor has no response, it already has a Maximum or Minimum speed. Motor Response P2 Jog x1 Beep x1 Down Jog x2 Beep x1 4 TM REMOTE | PROGRAMMING GUIDE b. Up Jog x1 Beep x1 b. Down Jog x1 Beep x1 Roller or Sheer Mode 1. Roller Shade Mode - continue movement after a short press - Default Mode a. Press and hold (about 5 sec) "Up" and "Down" buttons simultaneously until motor jog x1. b. Press and hold (about 2 sec) "Stop" button until motor jog x2 and beep x3. Action on Remote Control Motor Response Action on Remote Control Motor Response a. Up + Down Jog x1 b. Stop Jog x2 Beep x3 2. Sheer Shade Mode - jog movement after a short press (continue movement after a long press) a. Press and hold (about 5 sec) "Up" and "Down" buttons simultaneously until motor jog x1. Action on Remote Control Motor Response b. Press and hold (about 2 sec) "Stop" button until motor jog x1 and beep x1. Action on Remote Control Motor Response a. Up + Down Jog x1 b. Stop Jog x1 Beep x1 5 TM REMOTE | PROGRAMMING GUIDE Remote Function 1. Channel Options Select A Channel Action on Remote Control a. Press "<" button on the remote to select a lower channel. b. Press ">" button on the remote to select a higher channel. Remote Response a. Lower Channel 1 b. Higher Channel 15 Hide Unused Channels a. Press and Hold (about 3 sec) "<" and ">" buttons simultaneously until remote control displays "C" (channel). Action on Remote Control a. + Lower Higher Channel Channel Remote Response b. Press "<" or ">" button to select required quantity of C channel (between 1 to 15). c. Press "Stop" button to confirm selection (the example Action on c. shows a 5-channel selection). The LED will display "O" (OK) Remote Control Stop once to confirm selection. Remote Response 5 0 b. or Lower Higher Channel Channel 11 2. Advanced Setting - Disable Limit Setting a. Remove the cover from the backside of remote, the lock switch is in the right corner. b. Move the switch to the "Lock" position to disable the following commands, remote will show "L" (lock): - Change Motor Direction - Setting the Upper and Lower Limit - Adjust Limit - Roller Mode or Sheer Mode c. Move the switch to "Unlock" position to assess all remote functions, remote will show "U" (unlock). *This advanced feature is intended to be used after all shade programming is completed. User Mode will prevent accidental or unintended changing of limits. a. Switch b. Unlock Lock L Switch c. Unlock Lock U Switch 6 TM REMOTE | PROGRAMMING GUIDE P1 Button Instructions 2. P1 Button Location LED light P1 button Lithium Battery Switch 25B / 28B / 25BDC 2. P1 Button Instruction 1 Test Motor Happening as you press for 1 second Press P1 1 Less than 1 sec. 2 Activate Pairing Mode Happening as you press for 2 seconds Press P1 2 Approx. 2 sec. Until Shade: Jog x1 3 Sleep Mode Happening as you press for 6 seconds Press P1 6 Approx. 6 sec. Until Shade: Jog x2 4 Reverse Direction Happening as you press for 10 seconds Press P1 10 Approx. 10 sec. Until Shade: Jog x3 5 Reset To Factory Settings Happening as you press for 14 seconds Press P1 14 Approx. 14 sec. Until Shade: Jog x4 7 TM REMOTE | PROGRAMMING GUIDE when released Motor Response: Wakes & Runs when released Motor Response: Beep x1 when released Motor Response: Beep x2 when released Motor Response: Beep x3 when released Motor Response: Beep x4Adobe Acrobat Pro (64-bit) 23.1.20143