ARBOR HT10 Rugged Android Tablet Device

Overview

This guide provides essential information for setting up and using your ARBOR HT10 Rugged Android Tablet Device.

Package Contents

• 1 x HT10 Tablet
• 1 x Lithium Battery (10000mAh)
• 1 x Charger (5V/2A or 9V/2A)
• 1 x Type C USB Cable (1M)
• 1 x Quick Start Guide

Front View/Side View

The front and side views illustrate the device's buttons and ports:

• 1 Power Button
• 2 Volume Button
• 3 Scan Key
• 4 Light sensor
• 5 Charging LED
• 6 Front Camera
• 7 Scan LED
• 8 Barcode Scanner
• 9 POGOPIN
• 10 MIC
• 11 TF/Nano SIM Slots
• 12 USB Type-A
• 13 USB Type-C
• 14 Micro HDMI
• 15 NFC
• 16 LED Flash
• 17 Rear Camera
• 18 POGOPIN
• 19 Battery Cover Lock
• 20 Speaker
• 21 Battery Cover Lock
• 22 Battery
• 23 Battery Cover Lock

Rear View

The rear view shows the device's back panel components.

Installation

The HT10 comes with a Lithium battery. Ensure you use the provided battery to avoid explosion risks. Before installation, confirm all components are dry to prevent damage not covered by warranty.

1. Turn off the HT10. Move the battery cover lock buttons to the unlock position.
2. Gently pry off the battery cover from the grooves on the sides.
3. Insert the battery, connector side first, then press the battery down.
4. Replace the battery cover and move the battery cover lock buttons to the lock position.
5. Locate the microSD and Nano SIM card holder on the side and insert the card.
6. Push the card holder into the slot until it locks into place.

Charging

Charging Via a Computer

1. Open the TYPE-C cover on the right side of the HT10 to access the TYPE-C port.
2. Connect the HT10 to your computer using the provided TYPE-C USB cable.

Charging via AC Power

1. Open the TYPE-C cover on the right side of the HT10 to access the TYPE-C port.
2. Connect the HT10 to the provided power charger using the provided TYPE-C USB cable.
3. Connect the power charger to charge the HT10.

Notice: Using a battery or charger not provided with the HT10 may result in damage not covered by the warranty.

Turning On/Off

Turning On/Off the HT10

1. To turn on the HT10, long press the Power key for 3 seconds.
2. To turn off the HT10, press the Power key for 1 second, then a power menu will appear.

Sleeping/Awakening Mode

1. When the screen is on, press the Power key to put the HT10 into sleep mode.
2. When the screen is off, press the Power key to wake up the HT10.

Resetting

If the system stops responding, long press the Power key for approximately 15 seconds and then release to reset the HT10.

Power LED Status

Notices

• Do not use or charge the device in dusty or damp places, as this may cause the circuit to malfunction.
• Do not place the device near heaters or other heat sources.
• Keep the ambient temperature between -10°C and 50°C, and relative humidity between 10% and 90% RH for optimal device usage.
• Use only the charger and charging cable provided with the device.

Copyright Notice

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

Disclaimer

The information in this document is subject to change without prior notice to improve reliability, design, and function. It does not represent a commitment on the part of the manufacturer. The manufacturer will not be liable for any direct, indirect, special, incidental, or consequential damages arising from the use or inability to use the product or documentation, even if advised of the possibility of such damages.

Warranty Card

Dear Customer: To receive warranty service, please keep this warranty card and present it when requesting service.

FCC Compliance and RF Exposure Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) Information

This Mobile Phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.

FCC RF Exposure Information and Statement: The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: HT10 (FCC ID: 2AZNT-HT10) has also been tested against this SAR limit. The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction. The use of belt clips, holsters, and similar accessories should not contain metallic components. Accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

RF Specification

Manufacturer's Name: ARBOR Technology Corp.

Product Name: 10" Rugged Android Tablet Device

Trade Mark: ARBOR

Model Number(s): HT10, G1019, H79P, HT10A, HT10B, HT10C, HT10D, HT10E, HT10F, HT10G, HT10H, HT10J

This device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. All essential radio test suites have been carried out. The device complies with RF specifications when used at 0mm from your body. The product shall only be connected to a USB interface of version USB2.0.

This product can be used across EU member states. 5150-5350MHz indoor use restriction and member states.

Declaration of Conformity (DoC)

Manufacturer: ARBOR Technology Corp.

Address: 10F., No.700, Zhongzheng Rd., Zhonghe Dist., New Taipei City 235, Taiwan

Declare that the DoC is issued under their sole responsibility and belongs to the following product(s):

• Product Type: 10" Rugged Android Tablet Device
• Trademark: ARBOR
• Model Number(s): HT10, G1019, H79P, HT10 xxxxxxxxxx (x=0-9, a-z, A-Z and "-")

System Components:

• Adapter: Model: HJ-FC010K7-US, Input: 100-240V~50/60Hz 0.6A, Output: 5.0V 2.0A OR 9.0V 2.0A OR 12.0V 1.5A
• Battery: Model: CLP629, Specification: DC 3.8V, 1000mAh, Manufacturer: Shenzhen Cholipower Technology Co., Ltd.
• Antenna Manufacturer: SHENZHEN HAOTIAN CHENG WIRELESS TECHNOLOGY CO.,LTD.
• Antenna Details:
  • BT/WIFI2.4G antenna: FPC Antenna, Antenna Gain: 1.1 dBi
  • WIFI5G antenna: FPC antenna, Antenna Gain: 0.79dBi
  • 2G antenna: FPC Antenna, Antenna Gain: (GSM900: -0.61dBi)/(DCS1800: -1.22dBi)
  • 3G antenna: FPC Antenna, Antenna Gain: (Band I : 0.57dBi, Band VIII: -0.61dBi)
  • 4G: B1 : FPC Antenna, Antenna Gain: 0.57dBi ; B3:-1.22dBi ; B7 1.83dBi ; B8 -0.61dBi ; B20: -2.17dBi ; B28A :-3.54dBi ; B28B: -3.54dBi ; B34:2.81dBi ; B38: 2.81dBi ;B40: 1.73dBi
  • NFC: Induction coil
  • GPS: Ceramic Antenna

Optional Components:

• Hardware Version: V0.3
• Software Version: N/A

EU Declaration of Conformity

The object of the declaration described above is in conformity with the essential requirements of the relevant Union harmonization legislation: Radio Equipment Directive RED (2014/53/EU).

The following harmonized standards and technical specifications have been applied:

• HEALTH & SAFETY (Art. 3(1)(a)): EN 50566:2017; EN 62209-2:2010; EN 62479:2010; EN 62368-1:2014+A11:2017
• EMC (Art. 3(1)(b)): ETSI EN 301 489-1 V2.2.3 (2019-11), ETSI EN 301 489-3 V2.1.1 (2019-03), ETSI EN 301 489-17 V3.2.4 (2020-09), ETSI EN 301 489-19 V2.1.1 (2019-04), ETSI EN 301 489-52 V1.2.1 (2021-11), EN 55032:2015+A11:2020; EN 55035:2017+A11:2020, EN IEC 61000-3-2:2019; EN 61000-3-3:2013+A1:2019
• Radio Spectrum (Article 3.2): ETSI EN 300 328 V2.2.2 (2019-07); ETSI EN 301 893 V2.1.1 (2017-05); ETSI EN 301 511 V12.5.1 (2017-03); ETSI EN 300 440 V2.2.1 (2018-07); ETSI EN 301 908-1 V13.1.1 (2019-11); ETSI EN 301 908-2 V13.1.1 (2020-06); ETSI EN 301 908-13 V13.1.1 (2019-11); ETSI EN 303 413 V1.2.1 (2021-04); ETSI EN 300 330 V2.1.1 (2017-02)

Notified Body Involved:

• Notified Body: Eurofins Electrical and Electronic Testing NA, Inc.
• Notified Body Number: 0980
• Activity Performed: EU-Type Examination (Module B)

Technical file held by: ARBOR Technology Corp.

Address: 10F., No.700, Zhongzheng Rd., Zhonghe Dist., New Taipei City 235, Taiwan

Signed for and on behalf of: ARBOR Technology Corp.

Name and Title: Clark Lian / manager

Address: 10F., No.700, Zhongzheng Rd., Zhonghe Dist., New Taipei City 235, Taiwan