Buy Stage Lighting Equipment, Controls & Truss Structures | Texas | Mega Systems Inc
User Manual for MEGA LITE models including: Framebot 600, LED Moving Head Framing Light, Head Framing Light, Framing Light, Framebot 600, Light
Framebot 600 - MEGA-LITE
File Info : application/pdf, 15 Pages, 11.55MB
DocumentDocumentUSER MANUAL
Table of Contents
Safety Information.........................2 What's Included.............................2 Specifications................................3 Gobos & Colormation....................4 Colors............................................5 Main Power Connection................6 Installation.....................................7 Cleaning & Maintenance...............7 DMX Profile..................................11 Size & Weight..............................13 Warranty......................................14 Customer Service........................15
Check that the unit has not been damaged during transport.
Read Manual, Cautions, and Warnings Prior to operation of this equipment.
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
2. For indoor use only. Do not expose unit to rain or moisture.
3. Do not install the unit too close to a heat source.
4. Make sure cables are properly secured.
Fire
5. Maximum surface operating temperature: 130º.
Protection Against Electrical Fire
1. 2. 3. 4. Electrical
Disconnect power before servicing. For connection to main power supply, proceed to page 4. The power supply must be earthed (electronically grounded). This fixture must not be left on for long periods of time.
Protection Against Mechanical Hazards
1. Use secondary safety chain when hanging unit. 2. Use quality clamps or bolts when positioning unit. 3. Do not open unit while it is on. Risk of electrical shock.
Mechanical
What is Included 1pc Framebot 600 1pc Power Cable 2pc Quick Release Clamp Mount 1pc User Manual
2
Specifications
Part Numbers
Fixture
1190 - Framebot 600
Mechanical Specifications
Housing: Fastening System: Power Connection: Signal Connection: Pan Movement: Tilt Movement: Zoom Angle: Device Locking:
High Temperature Resistant Plastics By Directional Quick Release Clamp Mount Huashao power conn type (Nema 5-15 cable adapter included) 3 & 5 Pin XLR In and Out 540° (16 bit, 3 Phase stepper Motor) 270° (16 bit, 3 Phase stepper motor) 6.5° to 42° (16 bit) Pan And Tilt Transportation Lock
Electrical Specifications
Light Source: Color Temp WW: CRI: (Warm White) Color Flags: Color Wheel: Rotating Gobo's: Static Gobo's: Colormation: Prism: Iris: Frost: Focus: Strobe: Motorized Framing: Framing Rotation: RDM: Smart Cooling: Display:
580W White LED 6408K 70 Cyan, Magenta, Yellow, Kelvin (CMYK) 6 Color, Bi direction 6 Indexing, Bi directional, Changeable Gobo's 8 Fixed 1 continues rotation Colormation TM effect 1 4 Facet Indexing Prism 1 Linear adjustable Iris with Macro 1 Frost Filter Linear Focus (16 bit) 0.3-20 Per Second 4 Blade, Dual Motor, Single Blade Blackout 180° Indexing Rotation Yes Performance, Normal, Quiet Fan Modes 2.4" Color Display, Auto Flip
Power Supply: Power Consumption:
Electronic 100-240V AC 50/60 7.04 Amps / 807 Watts
3
Gobo's
Rotating Gobo's (Size 27.9mm, Image 22mm, Thickness Max 2.2mm)
1
6
5
Static Gobo's
2 1
2
3 4
3 4
8
7
Colormation TM
5 6
4
Colors
Color Mixing
Cyan
Magenta
Yellow
Color Wheel
Kelvin
Open 1 Red 2 Yellow 3 Green 4 Blue 5 Orange 6 Dark Blue
5
Main Power Connection
Caution!
1. Do not connect fixture to a dimmer system. 2. This unit must be earthed. (Electronically grounded) 3. Replace fuse only with the specified type and rating. (F20AL250V) 4. This device is equipped with auto switching power supply that will allow the fixture to work from
100V-240V AC 50/60Hz
Cable USA Black White Green
Cable EU Brown
Light Blue Yellow / Green
110V Live Neutral Ground
220V Live Live Ground
DMX-512 Connection
The fixture is equipped with 3 and 5 pin XLR Sockets for DMX input and output connection. The sockets are wired in parallel. Only use a shielded twisted pair cable designed for RS-485 and 3 or 5 pin XLR plugs and connectors in order to connect the controller with the fixture or the fixture with another.
DMX - Input
DMX - Output
1
2
3
1
5
2
4
3
1.Shield (Grd) 2. Signal (-) 3. Signal (+) N/A N/A
2
1
3
5
1
4
2
3
Caution!
On the last fixture the DMX signal needs to be terminated with a terminator. Pr-manufactured terminator are available for purchase from your Mega-Lite dealer item #P-DMX-T.
6
Installation Caution!
1. The Installation must be carried out by an authorized dealer or trained professional. 2. Unit may cause severe injures, if you have doubts concerning the safety do not install. 3. Unit is to be 24 inches away from flammable materials. 4. Use high quality installation equipment to hang the unit. 5. Internal Fan Filters must be cleaned periodically as not to block airflow.
When rigging the it is very important that you follow common safety procedures. Rigging requires extensive experience including but not limited to calculating working weight loads, material being used and periodic safety inspections. If you lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger. When rigging the unit always be secure with a secondary safety attachment. The installation location of the fixture has got to be built in the way that it can hold 10 times the weight for 1 hour with out any failures. Installation should be checked at least one time a year by a skilled professional. Fixture should not be installed in location were temperature will reach 113°F or colder than 23°F.
Cleaning and Maintenance
Installation Maintenance- The operator has to make sure that the unit is operating safely and has the installations and electronics checked by an expert every year. The following points must be considered during the inspection: 1)All screws used for installing the device or part of the device have to be tightly connected and must not be corroded. 2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing). 3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments. Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed. 4) Fixture housing must only be cleaned from the outside using only soap and water. 5) Internal fan filters but be cleaned periodically Note: Maintenance and service operations are to be carried out by authorized dealers. Replacing the fuse: When possible, only replace the fuse with the same type and rating. Replacing the power cable: If the power cable of this device becomes damaged, it has to be replaced by authorized dealers or trained professionals only. Should you have further questions, please contact your dealer.
7
Display Control
Main Control
The control board on the fixture base is your interface to access and control all the functions on the unit. It's LCD display gives you a code view of the options and functions. The following will explain each function.
®
Framebot 600
UP
MODE /ESC
ENTER
DOWN
i Information Settings
Manufacture Use
Display Lock
i
i ADDRESS
RUNTIME
VERSION
ADDRESS: Press Enter to view the fixture start. Press Enter again to make adjustment to the fixture address from 001 to 473 using the up/down buttons. Press Enter to confirm or Mode to go back. The fixtures start address will need to match the DMX Controllers assigned
TEMPERATURE DMX start channel.
FAN SPEED
i
i ADDRESS
RUNTIME
VERSION
RUNTIME: Press Enter for information regarding the fixtures time in use VERSION: Software version information. TEMPERATURE: Information on the lamp temperature FAN SPEED: Information of all the units fan speed
TEMPERATURE
FAN SPEED
i RESET CHANNEL SET SIGNAL
OFFLINE SET FAN MODE
RESET:
REBOOT: This function will reset all motor functions. DEFAULT DATA: This function will reset to original display factory settings
i RESET CHANNEL SET SIGNAL
OFFLINE SET FAN MODE
CHANNEL SET: 39
8
i RESET CHANNEL SET SIGNAL
OFFLINE SET FAN MODE
SIGNAL:
DMX 512 Framebot 600 WDMX = Available on Framebot 600 Pro PROGRAM = Framebot 600 Artnet = Available on Framebot 600 Pro
i RESET CHANNEL SET SIGNAL
OFFLINE SET FAN MODE
OFFLINE SET: Sets default setting of fixture losses input signal.
HOME: Will turn fixture to the home all channels 0 position. HOLD: Will hold the last signal received and will not change till receive new DMX command.
i RESET CHANNEL SET SIGNAL OFFLINE SET FAN MODE
i WIRELESS SET ADJUST ARTNET SET RDM UID
i WIRELESS SET ADJUST ARTNET SET RDM UID
FAN MODE: Sets the fixture fan speed
NORMAL: Will adjust the fan speed automatically depending on the fixtures internal temperature (recommended). PERFORMANCE: Fan speed will stay at he highest level to maintain fixtures performance level. QUIET: Fixtures lamp output will be reduced to adjust to fixtures safe operating temperature
WIRELESS SET: Links Wireless Solutions DMX (only available on Framebot 600 Pro)
Link: Select link from Wireless Transmitter and Link from the display for Wireless DMX Operation (signal will also need to be switched to WDMX) Unlink: Select unlink to disconnect from wireless transmitter
ADJUST: Fine adjustment of motor position
All Motor functions can be finely adjusted for best optical path performance
i WIRELESS SET ADJUST ARTNET SET
RDM UID
ARTNET SET: Artnet signal setup Available on the Framebot 600 Pro
9
i WIRELESS SET ADJUST ARTNET SET
RDM UID
RDM UID: Manufacture ID RDM Signal, Manufacture UID 6342 ID Mega Lite
i LANGUAGE
LANGUAGE: Display Language Option
BACKLIGHT
REVERSE DISPLAY
ENGLISH, RUSSIAN, CHINESE
i LANGUAGE
BACKLIGHT: Display view settings
BACKLIGHT
REVERSE DISPLAY
ON: Display will remain always on. OFF: Display will turn off after 30 seconds of no display use. FLASH: Display will turn of after 30 seconds no display use. And
the display will flash if DMX signal is lost.
i LANGUAGE
REVERSE DISPLAY: Display Orientation
BACKLIGHT
REVERSE DISPLAY
ON: Display will remain base to the bottom view. OFF: Display will invert to base on top view. Auto: Display will automatically invert depending base's position.
i SETTING LOCK
KEY LOCK
TEST
PROGRAM
SETTING LOCK & KEY LOCK: Display Lock
ON: Display will remain base to the bottom view. OFF: Display will invert to base on top view. Auto: Display will automatically invert depending base's position.
i SETTING LOCK KEY LOCK
TEST
PROGRAM
PROGRAM: Manually created programs
SELECT PROGRAMS: Select from 1-8 programs you would like to record EDIT PROGRAM: Adjust fixtures channel to be recorded. Press Enter to confirm. (Playback of programs is done in the Setting section under the Signal menu for Programs)
10
DMX Profile
Framebot 39Ch Mode
DMX Channel 1 2 3 4
Function Pan
Pan Fine Tilt
Tilt Fine
5
Color Wheel
6
Cyan
7
Magenta
8
Yellow
9
Kelvin
10
Static Gobo
11
Rotating Gobo
12
Gobo Rotation
13
Dimmer
14
Dimmer Fine
Description Pan
Pan Fine Tilt
Tilt Fine Open Red Yellow Green
Lime Green Orange
Dark Blue Open
Color By Position Counter Clockwise Rotation (Fast to Slow)
Clockwise Rotation (Slow to Fast) Cyan off to full
Magenta off to full Yellow off to full Kelvin off to full
Open Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 Gobo 8 Gobo By Position Counter Clockwise Rotation (Fast to Slow) Clockwise Rotation (Slow to Fast) Open Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Open Gobo By Position Counter Clockwise Rotation (Fast to Slow) Clockwise Rotation (Slow to Fast) No Function Gobo Rotation Index Counter Clockwise Rotation (Fast to Slow)
Stop Rotation Counter Clockwise (Slow to Fast)
Dimmer off to full Dimmer off to full
11
Value 0-255 0-255 0-255 0-255
0-7 8-15 16-23 24-31 32-39 40-47 48-55 56-63 64-221 222-239 240-255 0-255 0-255 0-255 0-255 0-7 8-15 16-23 24-31 32-39 40-47 48-55 56-63 64-71 72-143 144-199 200-255 0-7 8-15 16-23 24-31 32-39 40-47 48-55 56-63 64-135 136-195 196-255 0-3 4-123 124-187 188-191 192-255 0-255 0-255
Init Value 128 128 128 128
0
0 0 0 0
0
0
0 255 127
Open
0-10
Strobe (Slow to Fast)
4-103
Open
104-107
15
Shutter
Strobe Pulse (Slow to Fast)
108-207
0
Open
208-212
Random Strobe (Slow to Fast)
213-251
Open
252-255
Refresh Rate 1200
0-63
16
Dimmer Refresh
No Function
64-127
0
Refresh Rate 13672
128-191
No Function
192-255
17
Prism
Open
0-31
0
Prism Engage
32-255
No Rotation
0-3
Prism Index Rotation
4-123
18
Prism Rotation Counter Clockwise Rotation (Fast to Slow) 124-187
0
Stop
188-191
Rotation Counter Clockwise (Slow to Fast) 192-255
19
Zoom
Zoom
0-255
127
20
Zoom Fine
Zoom Fine
0-255
127
21
Focus
Focus
0-255
127
22
Focus Fine
Focus Fine
0-255
127
Open to Close
0-127
Close
128-135
23
Iris
Iris Pulse Close to Open (Slow to Fast) 136-173
0
Iris Pulse Open to Close (Slow to Fast) 174-211
Iris Bounce (Slow to Fast)
212-249
Close
250-255
24
Frost
No Function
0-9
0
Frost (clear to frost)
10-255
25
Colormation
No Function
0-7
0
Colormation Engage (linear)
8-255
No Function
0-7
26
Colormation Counter Clockwise Rotation (Fast to Slow) 8-127
0
Rotation
Stop
128-135
Rotation Counter Clockwise (Slow to Fast) 136-255
27
Frame 1A
Frame 1A Engage
0-255
0
28
Frame 1B
Frame 1B Engage
0-255
0
29
Frame 2A
Frame 2A Engage
0-255
0
30
Frame 2B
Frame 2B Engage
0-255
0
31
Frame 3A
Frame 3A Engage
0-255
0
32
Frame 3B
Frame 3B Engage
0-255
0
33
Frame 4A
Frame 4A Engage
0-255
0
34
Frame 4B
Frame 4B Engage
0-255
0
No Function
0-7
35
Frame Rotation
Frame Rotation
8-239
0
Frame Bounce
240-255
36
Frame Rot Fine
Frame Rotation Fine
0-255
127
37
Frame Macro
No Function
0-3
0
Frame Macro (1-63)
4-255
38
Scan Speed
Pan and Tilt Speed
0-255
0
No Function
0-19
Reset All
20-29
Reset Pan & Tilt
30-39
Reset Color, Gobo, CMYK
40-49
39
Control
Reset Zoom, Focus, Pism, Frost
50-59
0
(hold for 8 sec)
Reset Colormation, Iris, Framing
60-69
Display Default
70-79
Display Off
80-89
No Function
90-255
13
Size and Weight
2.12"
11.09"
2.12"
7.5"
17.5" 15.33"
11.75"
21.13" 25"
4.54"
3.87"
13.33"
14.13"
Fixture Size:
15.33" X 13.33" X 25"
Fixture Weight:
56lb
Packaged Size: 30.5" X 18.5" X 21.5"
Packaged Weight: 66lb
14
General Terms & Conditions
1. All resellers must have approved and signed Reseller Application on file, including their respective state tax information and W-9. Applications are re-evaluated on a fiscal calendar year basis to assure business integrity and tax status. 2. Cash, check, cashiers check, ACH, wire transfer, MasterCard, Visa, Discover, and American Express are accepted forms of payment. 3. Past due invoices will be charged 1.5% per month finance charge. Uncollected invoices are subject to be turned over to collection. 4. The reseller will pay all reasonable expenses incurred in the course of collections. 5. The proper venue for litigation will be Bexar County, Texas. 6. Returned checks will be charged a $50.00 fee. 7. All prices are in U.S. Dollars. 8. All prices and specifications are subject to change without notice, sales order confirmations are emailed and will reflect correct pricing. 9. All terms are insured, monitored, analyzed and approved by Co-face USA. Changes in credit line and approved terms can change without notice. Company authorization of credit is based on Co-face approvals. Any conflicts or disagreements should be referred to: 650 College Rd East Suite 2005 Princeton, NJ 08540. 1-609-469-0400. E-mail: cofaceusa@coface.com 10. Returns are subject to 25% restocking charge plus any necessary charges for repair or re-packaging.
Shipping Terms & Conditions
1. All orders are EXW San Antonio, TX (EXW means that a buyer/reseller incurs the risks for bringing the goods to their final destination) any deviation needs to be done in writing. 2. UPS ground shipping is the preferred shipping method. Requests for specific carriers may require use of the customer's account number and may incur an additional charge for handling. 3. Drop shipments are subject to all return charges at resellers expense. Drop shipments are not allowed outside of the territorial United States. 4. NO C.O.D. shipments allowed. 5. Returned and undelivered shipment charges are the buyer/resellers responsibility and will be billed to the buyer/reseller. 6. The freight carrier and Company shipping@mega.lighting should be notified upon receipt of damaged freight, discrepancies, or non-conformities within 24 hours. Company can assist in making claims with carriers or agents in the event of any loss or damage. 7. Upon acceptance in good order by Carrier from Company, the material becomes the property of the Reseller.
Warranty and Service Procedures
1. All returns require an RMA# (Return Merchandise Authorization number) before returning goods for any reason. For a service or warranty RMA, please email service@mega.lighting or call (210)684-2600. For sales or demo returns, please contact sales@mega.lighting. 2. Case will be created and an RMA notice will be emailed. All units received must have the RMA # included with the unit as well as on the shipping label. 3. All shipping charges are the responsibility of the customer: MEGA Systems, Inc., Service, 18668 HWY 16 N., Helotes, TX 78023
Warranty for Products Purchased Before 2021
Unless otherwise stated in writing, product is covered by a one year parts and labor limited warranty and is subject to same limitations listed under the limited warranty exclusions listed below.
Warranty for Products Purchased After January 1, 2021
MEGA SYSTEMS INC ("MSI") hereby warrants to the original purchaser/owner (Customer"), MSI products to be free of manufacturing defects in material and workmanship, for the warranty periods as defined below from the original purchase invoice date. This warranty applies exclusively to new MSI branded and/or distributed products listed below, purchased from an MSI AUTHORIZED dealer/reseller. This warranty is not transferable and may or may not apply to products sold and/or forwarded outside the United States. Please contact MSI for applicable regional product warranty information.
The purchase of MSI product constitutes the Customer's acceptance of all warranty terms and conditions as listed in this limited warranty statement. This warranty provides the Customer with legal rights, which may vary from state to state. Please contact MSI regarding warranty questions prior to purchasing.
Product / Series
Warranty Period
Coverage
Battery Powered LED
Six month battery, one year all other components
1, 2
Moving LED, Hazers
One Year
2
Outdoor IP-Rated LED
Two Years
3
House Light LED, Decorative LED, Compact LED, iCandy LED, Theatrical LED, Strobe Wash LED, Follow Spot LED, Three Years
4
Production & House of Worship Control, Architectural Control, Theatrical Control, Dance Venue & Mobile DJ Control,
Direct View LED Displays, and MV Controllers
1. Battery: 183 days/six months 2. Parts and Labor: 365 days/one year 3. Parts and Labor: 730 days/two years 4. Parts and Labor: 1095 days/three years
This limited warranty excludes any defects caused by, resulting from, or relating to the following: Normal wear and tear of lamps, color media, brushes, contact rings, lamp sockets, belts and other parts prone to wear and tear. Misuse, abuse, improper handling, accident, alteration or attempts to repair by or on behalf of the owner or any person not authorized by MSI. Damage to the product resulting from acts of God, including but not limited to, earthquakes, hurricanes, tornadoes, lightning and other natural disasters, fire, explosion, flood, riots, civil disorder or any other cause beyond the reasonable control of MSI. Exposure to harsh or excessively corrosive environmental conditions (whether indoors or outdoors) including, but not limited to, extreme temperature, humidity, atmospheric conditions (including salinity or pressure), radiation (UV, infrared or nuclear), shock and conditions which exceed the product's Ingress Protection ("IP") rating. Use of the product in a manner which exceeds the applicable product specification, including, but not limited to, exposure to excessive, insufficient, or other voltage conditions. Installation or use of the product not in accordance with the technical documentation, MSI guidelines (as may be posted on its website at www.megasystemsinc.com from time to time or otherwise designated by MSI or its brands) or applicable building and electrical codes, regulations, and standards. Failure to maintain the product in accordance with the technical documentation. Natural degradation and color shift of the LED source over the course of normal product use. Slight deviations in the specified values of intensity and color that do not affect the functionality of the product. Use of the product not for its intended purpose.
All warranty claims are evaluated under the terms of this limited warranty. If a product falls within the warranty period and if, upon examination by MSI, it is found to have failed for a covered cause, MSI will, at its sole discretion, repair or replace the defective part or product or reimburse the purchaser a pro-rated portion of the purchase price based on the percentage of the warranty period still remaining as of the date that the returned product was received by MSI. Should a replacement part or product be discontinued or unavailable, MSI reserves the right, in its sole and absolute discretion, to substitute a comparable replacement part or product for the defective part of product. MSI warranty obligation hereunder is limited solely to the repair or replacement of or reimbursement for the particular parts or products determined by MSI to have failed for a covered cause within the warranty period. In no event shall MSI be responsible to replace or reimburse purchaser for any products or portions of a system that MSI determines has not failed for a covered cause within the warranty period, even if such other products or portions of a system are used together with products being repaired or replaced by MSI under this warranty and the repaired product differs in brightness, colors or any other attribute after the repair.
Costs of removal, shipping to MSI or its authorized representative and re-installation are solely the responsibility of the purchaser. If MSI determines that the product is covered by this limited warranty, it will only pay for parts and labor as indicated by product type. If MSI determines that the product is not covered by this limited warranty, the purchaser will have the option of paying for the repair if the product can be repaired and the purchaser shall be responsible for the cost of shipping the repaired product back to the purchaser. MSI reserves the right, in its sole and absolute discretion, to decline any repair.
IN NO EVENT SHALL MEGA SYSTEMS, INC. BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, INDIRECT OR PUNITIVE LOSS OR DAMAGE OF ANY KIND, INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUES, LOSS OF USE OF THE PRODUCT OR ANY OTHER GOODS OR ASSOCIATED EQUIPMENT, DAMAGE TO ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE PRODUCTS, FACILITIES OR SERVICES, DOWN TIME COST, INSTALLATION OR LABOR COSTS, OR CLAIMS OF THE PURCHASER'S CUSTOMERS, WHETHER BASED ON WARRANTY, CONTRACT OR NEGLIGENCE, ARISING IN CONNECTION WITH THE SALE, USE OR REPAIR OF THE PRODUCT. MEGA SYSTEMS INC'S MAXIMUM LIABILITY SHALL NOT, IN ANY CASE, EXCEED THE PURCHASE PRICE OF THE PRODUCT THAT GIVES RISE TO THE CLAIM.
EXCEPT FOR THE LIMITED WARRANTY SET FORTH HEREIN, ALL PRODUCTS SOLD BY MEGA SYSTEMS, INC. ARE SOLD "AS IS" WITHOUT ANY WARRANTY, EXPRESS, OR IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ALL OF WHICH ARE EXPRESSLY AND SPECIFICALLY DISCLAIMED BY MEGA SYSTEMS, INC.
15
Customer Support
MEGA-Lite has a customer support line to provide set-up help and to answer any questions should you encounter a problem. Please visit our website for any other related technical documents. For service related issues, please contact our service dept.
Monday - Friday 9am to 6pm CST (210)684-2600 Service@mega.lighting
Manual Version
Please visit www.mega.lighting for the most up-to-date manual version.
Manual Version 1.0
Date 01/04/2022
Fixture Software N/A
Notes
®
MEGA-LITE 18668 Highway 16N Helotes, TX 78023 Phone (210)684-2600 / Fax (210)855-6279 www.mega.lighting / info@mega.lighting