Behringer PM1 Quick Start Guide
Safety Instructions
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Use only attachments/accessories specified by the manufacturer.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
- Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office, or your household waste collection service.
- Do not install in a confined space, such as a book case or similar unit.
- Do not place naked flame sources, such as lighted candles, on the apparatus.
Controls
(1) XLR Input: Locking jack accepts an XLR male plug for connection of a stereo personal monitor mix. Press the release tab to disconnect the cable. Signals should be sent from a stereo headphone amplifier to the PM1. Note that the PM1 XLR input is not meant for balanced line signals. To connect a stereo source, such as a headphone amplifier, use a TRS-to-XLR cable. Alternatively, you can use a dual 1/4" TS-to-XLR cable (two 1/4" mono connectors to a single XLR male connector) to connect a stereo signal on separate outputs, or a pair of aux sends.
(2) VOLUME knob: Adjusts the output level.
(3) HEADPHONE output: Allows connection of a 1/8" stereo mini jack.
(4) BELT CLIP: Attaches to a belt or pant waistline for hands-free use.
Specifications
Feature | Details |
---|---|
Input Type | XLR, stereo |
Output Type | 1/8" TRS, stereo |
Maximum Power Handling | 100 mW |
Headphone impedance | 32-600 Ohm |
Physical Dimensions (H x W x D) | 31 x 31 x 88 mm (1.2 x 1.2 x 3.5") |
Weight | 80 g (0.2 lbs) |
Legal Disclaimer and Warranty
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2023 All rights reserved.
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at community.musictribe.com/pages/support#warranty.
Compliance and Representatives
Music Tribe declares that this product is in compliance with Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC. Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S, Address: Gammel Strand 44, DK-1202 København K, Denmark
UK Representative: Music Tribe Brands UK Ltd., Address: 6 Lloyds Avenue, Unit 4CL London EC3N 3AX, United Kingdom