User Guide for ANALOG DEVICES models including: EVAL-AD5675RARDZ Controller Board, EVAL-AD5675RARDZ, Controller Board, Board
AD5675R Datasheet and Product Info | Analog Devices
EVAL-AD5675RARDZ - Analog Devices - Evaluation Board, AD5675RBRUZ, 16Bit
File Info : application/pdf, 16 Pages, 2.51MB
DocumentDocumentUser Guide | EVAL-AD5675RARDZ/EVALAD5676RARDZ
UG-2148
Evaluating the AD5675R (I2C) or the AD5676R (SPI) Octal, 16-Bit nanoDAC+ with 2 ppm/°C Reference
FEATURES
TYPICAL EVALUATION BOARD SETUP
Full featured evaluation board for the AD5675R (I2C) and AD5676R (SPI)
Various link options
PC control in conjunction with the Analog Devices, Inc., EVALSDP-CK1Z (SDP-K1) controller board
EVALUATION KIT CONTENTS
EVAL-AD5675RARDZ (I2C) or EVAL-AD5676R2ARDZ (SPI) evaluation board
AD5675R (I2C) or AD5676R (SPI) device
HARDWARE REQUIRED
EVAL-SDP-CK1Z (SDP-K1) controller board, which must be purchased separately
Figure 1. Evaluation Board Connected to the SDP-K1 Controller Board (EVAL-AD5675RARDZ or EVAL-AD5676R2ARDZ)
SOFTWARE REQUIRED
Analysis | Control | Evaluation (ACE) Software, which is available for download from the EVAL-AD5675RARDZ (I2C) or EVALAD5676R2ARDZ (SPI) product page
GENERAL DESCRIPTION
This user guide details the operation of the EVAL-AD5675RARDZ (I2C) evaluation board and the EVAL-AD5676R2ARDZ (serial peripheral interface (SPI)) evaluation board for the AD5675R (TSSOP, I2C) and AD5676R (TSSOP, SPI), respectively, which are both octal channel, voltage output digital-to-analog converters (DACs).
The EVAL-AD5675RARDZ and the EVAL-AD5676R2ARDZ evaluation boards are designed to facilitate quick prototyping of the AD5675R or AD5676R circuits, thereby reducing design time. Both devices operate from a single 2.7 V to 5.5 V supply. Additionally, these devices both have an internal 2.5 V reference. A different reference voltage (VREF) can be applied via the EXT_REF SMB connector, if required. While sharing common features, the two DACs differ in their digital interface protocols. The AD5676R employs SPI, while the AD5675R employs I2C.
The EVAL-AD5675RARDZ and the EVAL-AD5676R2ARDZ evaluation boards interface to the USB port of a PC via a System Demonstration Platform (SDP) controller board (EVAL-SDP-CK1Z (SDP-K1)). The Analysis | Control | Evaluation (ACE) software is available for download from both the EVAL-AD5675RARDZ product page and the EVAL-AD5676R2ARDZ product page. This software can be used with the evaluation board to allow the user to program the AD5675R and AD5676R, respectively. A PMOD connection is also available to allow the connection of microcontrollers to either evaluation board. Note that when a microcontroller is used through
the PMOD connection, the EVAL-SDP-CK1Z (SDP-K1) must be disconnected, and the user cannot use the ACE software.
The EVAL-AD5675RARDZ and the EVAL-AD5676R2ARDZ both require the EVAL-SDP-CK1Z (SDP-K1) controller board, which are available for purchase from Analog Devices.
For full details on the AD5675R and the AD5676R, see the AD5675R and AD5676R data sheets, which must be consulted in conjunction with this user guide when using the EVALAD5675RARDZ or the EVAL-AD5676R2ARDZ evaluation boards.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | 1 of 16
User Guide
EVAL-AD5675RARDZ/EVAL-AD5676RARDZ
TABLE OF CONTENTS
Features................................................................ 1 Evaluation Kit Contents......................................... 1 Hardware Required............................................... 1 Software Required.................................................1 Typical Evaluation Board Setup.............................1 General Description...............................................1 Getting Started...................................................... 3
Installing the Software........................................ 3 Initial Setup.........................................................3
Block Diagram and Description............................. 4 Memory Map...................................................... 5
Evaluation Board Hardware...................................6 Power Supplies.................................................. 6 Link Options....................................................... 7
Evaluation Board Schematics................................8 Ordering Information............................................14
Bill of Materials................................................. 14
REVISION HISTORY 1/2024--Revision 0: Initial Version
analog.com
Rev. 0 | 2 of 16
User Guide
EVAL-AD5675RARDZ/EVAL-AD5676RARDZ
GETTING STARTED
INSTALLING THE SOFTWARE
The EVAL-AD5675RARDZ (I2C) or EVAL-AD5676R2ARDZ (SPI) evaluation boards use the Analog Devices the Analysis | Control | Evaluation (ACE) software, a desktop software application that allows the evaluation and control of multiple evaluation systems.
The ACE software is available for download from the EVALAD5675RARDZ evaluation board page or EVAL-AD5676R2ARDZ evaluation board page and must be installed before connecting the EVAL-SDP-CK1Z (SDP-K1) controller board to the USB port of the PC to ensure that the EVAL-SDP-CK1Z (SDP-K1) is recognized when it connects to the PC. The ACE installer installs the necessary SDP drivers and the Microsoft® .NET Framework 4 by default. For full instructions on how to install and use this software, see the ACE software page on the Analog Devices website.
After the ACE software installation completes and the software is opened, the EVAL-AD5675RARDZ or EVAL-AD5676R2ARDZ evaluation board plugin appears.
INITIAL SETUP
To set up the EVAL-AD5675RARDZ or EVAL-AD5676R2ARDZ evaluation board, take the following steps:
1. Connect the EVAL-AD5675RARDZ or EVAL-AD5676R2ARDZ to the EVAL-SDP-CK1Z (SDP-K1) controller board and then connect a USB cable between the SDP-K1 and the PC.
2. Run the ACE software, and the main window appears as shown in Figure 2. The EVAL-AD5675RARDZ or EVALAD5676R2ARDZ board plugins appear in the Attached Hardware section of the Start tab.
3. Double-click the board plugin to open the board view shown in Figure 3.
4. Double-click the AD5675R or AD5676R chip to access the chip view as shown in Figure 4. This view provides a basic representation of functionality of the board. See Figure 5 and Table 1 for the details on the main function blocks of the board.
Figure 3. Board View of the EVAL-AD5675RARDZ or EVAL-AD5676R2ARDZ Figure 4. Chip Block Diagram View of the AD5675R or AD5676R
Figure 2. ACE Software Main Window analog.com
Rev. 0 | 3 of 16
User Guide
EVAL-AD5675RARDZ/EVAL-AD5676RARDZ
BLOCK DIAGRAM AND DESCRIPTION
The EVAL-AD5675RARDZ or EVAL-AD5676R2ARDZ software is organized so that it appears similar to the functional block diagram shown in the data sheets. In this way, it is easy to correlate the functions on the board with the descriptions in the data sheets. A full description of each block, register, and its settings is given in the AD5675R or AD5676R data sheets.
Some of the blocks and their functions are described in this section as they pertain to the EVAL-AD5675RARDZ and EVALAD5676R2ARDZ. The block diagram is shown in Figure 5, and Table 1 describes the functionality of each block.
Table 1. Block Diagram Functions
Label Button/Function Name
A
Configuration Summary
B
LDAC and RESET (GPIO
buttons)
C
Select a Command
D
Channel page selection
E
Input register
F
DAC register
G
Software RESET
H
Load DAC
I
DAC
J
Internal Reference
K
Apply Changes
Figure 5. Block Diagram with Labels
Function
This function is used to set up the initial configuration for the evaluation board. Select the reference gain from the Configuration dropdown menu. A gain of 1 is the default. For a gain of 2, an external supply is needed (VDD = VREF + 1.5 V). After setting up the initial configuration, click Apply Changes (K) to apply the values. These settings can be modified at any stage while evaluating the board. The LDAC and RESET buttons act as external GPIO pulses to the LDAC and RESET pins. The LDAC button transfers data from the input registers (E) to the DAC registers (F). The RESET button clears all data from the input registers and DAC registers. These buttons are live; therefore, there is no need to click Apply Changes (K). The Select a Command dropdown menu controls how the data transfer to the device affects the input and DAC registers. When a data value is entered in an input register (E), this menu determines if the data is transferred to the input register only, or to the channel input register (E) and channel DAC register (F). Use the change page display dropdown menu to select which page of the four DAC channel settings displays. The function is used to select the 16-bit data-word to transfer to the device. Then, click Apply Changes (K) to transfer the 16-bit data-word to the device. This box displays the value that is currently present in the DAC register on the device. Select the appropriate command option or toggle LDAC (B) to update the DAC register. Click Software RESET to return the evaluation board and software to their default values. This button is live; therefore, there is no need to click Apply Changes (K). Click Load LDAC to individually control which channel loads the values from the input register to the DAC register. The DAC configuration options provide access to individual channel configuration options, such as power-down options and hardware LDAC mask enable and disable settings. In the Internal Reference area, select Enable from the dropdown menu to enable the on-chip reference for the evaluation board. If Disable is selected, an external reference must be applied. Click Apply Changes to update the device with all the modified values. However, if there is no evaluation board connected, the input register value is not transferred to the DAC register.
analog.com
Rev. 0 | 4 of 16
User Guide
EVAL-AD5675RARDZ/EVAL-AD5676RARDZ
BLOCK DIAGRAM AND DESCRIPTION
MEMORY MAP
All registers are fully accessible from the memory map tab. The memory map allows registers to be edited at a bit level. The bits shaded in dark gray are read only bits and cannot be accessed from ACE. All other bits are toggled. Click Apply Changes to transfer data to the device. All changes here correspond to the
block diagram; for example, if the internal register bit is enabled, it shows as enabled on the block diagram. Any bits or registers that are in bold are modified values that have not been transferred to the evaluation board. After clicking Apply Changes, data is transferred to the evaluation board.
Figure 6. AD5675R or AD5676R Memory Map
Figure 7. AD5675R or AD5676R Memory Map with Pending Changes in DAC0_Input_Register
analog.com
Rev. 0 | 5 of 16
User Guide
EVAL-AD5675RARDZ/EVAL-AD5676RARDZ
EVALUATION BOARD HARDWARE
Before applying power and signals to the EVAL-AD5675RARDZ or EVAL-AD5676R2ARDZ, ensure that all link positions are as required by the operating mode. The two modes available for operating the evaluation board are SDP control mode, which must be used with the EVAL-SDP-CK1Z (SDP-K1), or standalone mode where an external supply must be provided.
POWER SUPPLIES
The EVAL-AD5675RARDZ and EVAL-AD5676R2ARDZ evaluation boards provide an onboard, 3.3 V regulator powered through the USB supply. If the evaluation board is controlled through a PMOD, or a gain of 2 is required, an external supply must be provided
Table 2. Power Supply Connectors
Connector
Label
EXT_VDD, Pin 1 EXT_VDD, Pin 2 EXT_VREF, SMB Connector
EXT_VDD AGND EXT_VREF
via the EXT_VDD connectors. See Table 2 and the power requirements specifications in the AD5675R or AD5676R data sheets for additional details.
Both the AGND and DGND inputs are provided on the board. The AGND and DGND planes are connected at one location close to the AD5675R or AD5676R. To avoid ground loop problems, it is recommended that AGND and DGND not be connected elsewhere in the system.
All supplies are decoupled to ground with 10 µF and 0.1 µF capacitors.
External Voltage Supplies Description External analog power supply from 2.7 V to 5.5 V, VDD. Analog ground. External voltage reference.
analog.com
Rev. 0 | 6 of 16
User Guide
EVAL-AD5675RARDZ/EVAL-AD5676RARDZ
EVALUATION BOARD HARDWARE
LINK OPTIONS
A number of link options are incorporated in the EVALAD5675RARDZ or EVAL-AD5676R2ARDZ evaluation board and must be set for the required operating conditions before using the board. The link function options are described in Table 4.
Table 3. Link Options Setup for SDP-K1 Control (Default) Link
VDD_SEL REF_SEL VDD_VIO RSTSEL GAIN
Table 3 lists the positions of the different links controlled by the PC via the USB port, and an SDP controller board operating in single-supply mode is required.
Option Position A (1-2) Position A (1-2) Disconnected Position A (1-2) Position 1-2
Table 4. Link Functions
Link
Description
VDD_SEL This link selects the DAC analog voltage source. There are two options, as follows.
Position A (1-2): This option selects the on-board voltage source (SDP-K1, ADP121). Position B (2-3): This option selects an external supply voltage (EXT_VDD connector).
REF_SEL This link selects the DAC voltage reference source:
Position A (1-2): This option selects an external reference source (EXT_VREF connector). If no external supply present, it defaults to the internal on-chip reference.
Position B (2-3): This option selects the on-board reference from the ADR4525
VDD_VIO
This link selects the DAC digital voltage source. There are two options, as follows. Connected: shorts VDD and VLOGIC. Only use this option when the SDP-K1 controller board is not connected. Disconnected: opens the connection of VDD and VLOGIC. Use this option when using the SDP board.
RSTSEL
The RSTSEL (reset select) link selects the power-on reset state of the device. Position A (1-2): This option ties this pin to DAC_VLOGIC and powers up all DACs to midscale. Position B (2-3): This option ties this pin to DGND and powers up all DACs to zero scale.
GAIN
This link sets the internal gain setting of the device.
Position 1-2: This link is the default option, and it selects the control (GAIN_IO) option, in which, the gain is controlled by the ACE software using the EVAL-SDP-CK1Z (SDP-K1).
Position 3-4: This option ties the GAIN pin to DAC_VLOGIC and results in all DAC outputs having a 0 V to 2 × VREF span. Position 5-6: This option ties the GAIN pin to DGND and results in all DAC outputs having a 0 V to VREF span.
analog.com
Rev. 0 | 7 of 16
User Guide
EVAL-AD5675RARDZ/EVAL-AD5676RARDZ
EVALUATION BOARD SCHEMATICS
Figure 8. NanoDAC+ Evaluation Board Schematic Diagram, Power Supply and Signal Routes, Page 1
analog.com
Rev. 0 | 8 of 16
User Guide
EVAL-AD5675RARDZ/EVAL-AD5676RARDZ
EVALUATION BOARD SCHEMATICS
Figure 9. NanoDAC+ Evaluation Board Schematic Diagram, Power Supply and Signal Routes, Page 2
analog.com
Rev. 0 | 9 of 16
User Guide
EVAL-AD5675RARDZ/EVAL-AD5676RARDZ
EVALUATION BOARD SCHEMATICS
Figure 10. NanoDAC+ Evaluation Board Schematic Diagram, SDP Connector
Figure 11. NanoDAC+ Evaluation Board Schematic Diagram, PMOD Connection
analog.com
Rev. 0 | 10 of 16
User Guide
EVAL-AD5675RARDZ/EVAL-AD5676RARDZ
EVALUATION BOARD SCHEMATICS
Figure 12. NanoDAC+ Evaluation Board, Component Placement
analog.com
Rev. 0 | 11 of 16
User Guide
EVAL-AD5675RARDZ/EVAL-AD5676RARDZ
EVALUATION BOARD SCHEMATICS
Figure 13. NanoDAC+ Evaluation Board, Top Side Routing
analog.com
Rev. 0 | 12 of 16
User Guide
EVAL-AD5675RARDZ/EVAL-AD5676RARDZ
EVALUATION BOARD SCHEMATICS
Figure 14. NanoDAC+ Evaluation Board, Bottom Side Routing
analog.com
Rev. 0 | 13 of 16
User Guide
EVAL-AD5675RARDZ/EVAL-AD5676RARDZ
ORDERING INFORMATION
BILL OF MATERIALS
Table 5. Bill of Materials Quantity Reference Designator
Description
Supplier/Part Number1
1
U1
Octal, 16-bit nanoDAC+ with 2 ppm/°C reference
Analog Devices, AD5676RBRUZ or AD5675RBRUZ
1
U2
IC, 32 KBIT serial, electrically erasable programmable read-only Generic memory (EEPROM)
1
U3
150 mA, low quiescent current, complementary metal-oxide semiconductor (CMOS) linear regulator in 5-lead TSOT or 4-ball WLCSP
Analog Devices, ADP121-AUJZ33
1
U4
Ultra-low noise, high-accuracy 2.5 V voltage reference
Analog Devices, ADR4525DEZ
2
AGND, DGND
Connector, printed circuit board (PCB), black test points
Generic
1
C1
0.1 F ceramic capacitor, 16 V, 10%, X7R, 0402, AEC-Q200
Generic
2
C4, C10
0.1 F ceramic capacitors, 50 V, 10%, X7R, 0603
Generic
4
C6, C8, C11, C23
0.1 F ceramic capacitors, 16 V, 10%, X7R, 0603
Generic
3
C9, C12, C14
1 F ceramic capacitors, 16 V, 10%, X7R, 0603
Generic
2
C5, C13
10 F ceramic capacitors, 10 V, 20%, X5R, 0603
Generic
1
C2
10 F ceramic capacitor, 6.3 V, 20%, X5R, 0603
Generic
1
C3
4.7 F ceramic capacitor, 10 V, 20%, X5R, 0603
Generic
1
E1
Inductor, ferrite bead, 600 , 25%, 100 MHz, 2.9 A, 0.038 , 1206, AEC-Q200
Generic
1
EXT_VDD
Connector, PCB, 2-position terminal block side entry 5 mm pitch Generic
1
EXT_VREF
Connector, PCB coax Subminiature Version B (SMB) jack RF vertical PC mount gold
Generic
6
LDACB, RESETB, SCLK/A0, SDI/A1, SDO/ Connector, PCB white test points
SDA, SYNCB/SCL
Generic
1
P1
Connector, PCB receptacle 25 mil square post, 2.54 mm pitch Generic
2
P2, P5
Connector, PCB receptacles 25 mil square post, 2.54 mm pitch Generic
1
P3
Connector, PCB BERG header, double straight male, 6-position Generic
1
P4
Connector, PCB receptacles 25 mil square post, 2.54 mm pitch Generic
1
R1
0 resistor, surface-mounted device (SMD), jumper, 1/16 W, 0402 Generic
3
R8, R9, R12
100 k resistors, SMD, 1%, 1/16 W, 0603
Generic
8
R33
0 resistors, SMD, jumper, 1/10 W, 0603
Generic
1
R2
1.6 resistor, SMD, 1%, 1/5 W, 0603, AEC-Q200
Generic
1
R3
0 resistor, SMD, jumper, ½ W, 0805, AEC-Q200, pulse proof Generic
2
R4, R36
100 k resistors, SMD, 1%, 1/10 W, 0603
Generic
3
REF_SEL, RSTSEL, VDD_SEL
Connector-PCB, high temperature, 3-position, male headers,
Generic
unshrouded, single row straight, 2.54 mm pitch, 3.05 mm solder
tail
11
VDD, VLOGIC, VOUT0, VOUT1, VOUT2, Connector-PCB red test points
VOUT3, VOUT4, VOUT5, VOUT6, VOUT7,
VREF
Generic
1
VDD_VIO
Connector-PCB, header, 1 row, 2 way
Generic
6
R5, R14, R17, R19, R22, R35
0 resistors, SMD, jumper, 1/10 W, 0603
Generic, install for EVAL-AD5676R2ARDZ
6
R6, R13, R16, R18, R21, R23
0 resistors, SMD, jumper, 1/10 W, 0603
Generic, install for EVAL-AD5675RARDZ
8
R6, R13, R15, R16, R18, R20, R21, R23 0 resistors, SMD, jumper, 1/10 W, 0603, do not insert (DNI) or Not applicable
do not populate (DNP) for EVAL-AD5676R2ARDZ
8
R5, R14, R15, R17, R19, R20, R22, R35 0 resistors, SMD, jumper, 1/10 W, 0603, DNI or DNP for
Not applicable
EVAL-AD5675RARDZ
1
R34
0 resistor, SMD, jumper, 1/10 W, 0603, DNI or DNP for both boards
Not applicable
analog.com
Rev. 0 | 14 of 16
User Guide
EVAL-AD5675RARDZ/EVAL-AD5676RARDZ
ORDERING INFORMATION
Table 5. Bill of Materials (Continued)
Quantity Reference Designator
1
R32
8
C15 C16, C17, C18, C19, C20, C21, C22
1
C7
1
PMOD
3
R7, R10, R11
8
R24, R25, R26, R27, R28, R29, R30, R31
8
VOUT_0, VOUT_1, VOUT_2, VOUT_3,
VOUT_4, VOUT_5, VOUT_6, VOUT_7
Description
Supplier/Part Number1
100 k resistor, SMD, 1%, 1/10 W, 0603, AEC-Q200, DNI or DNP for both boards 10 nF ceramic capacitors, 200 V, 10%, X7R, 0805, FLEXITERM®, DNI or DNP for both boards
Not applicable Not applicable
0.1 F ceramic capacitor, 16 V, 10%, X7R, 0603, DNI or DNP for Not applicable both boards
Connector, PCB BERG header, straight male, 12-position, DNI or Not applicable DNP for both boards
0 resistors, SMD, jumper, 1/10 W, 0603, AEC-Q200, precision Not applicable power, DNI or DNP for both boards
1 k resistors, SMD, 1%, 1/8 W, 0805, AEC-Q200, DNI or DNP for Not applicable both boards
Connector-PCB, coax SMB, jack, RF vertical, PC mount gold, DNI Not applicable or DNP for both boards
1 Generic indicates that any part with the specified value, size, and rating can be used.
analog.com
Rev. 0 | 15 of 16
User Guide
NOTES
EVAL-AD5675RARDZ/EVAL-AD5676RARDZ
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of
functionality.
Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the "Evaluation Board"), you are agreeing to be bound by the terms and conditions set forth below ("Agreement") unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you ("Customer") and Analog Devices, Inc. ("ADI"), with its principal place of business at Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term "Third Party" includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED "AS IS" AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER'S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI'S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2024 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. One Analog Way, Wilmington, MA 01887-2356, U.S.A.
Rev. 0 | 16 of 16
Mixed-signal and digital signal processing ICs | Analog DevicesMixed-signal and digital signal processing ICs | Analog DevicesAnalysis | Control | Evaluation (ACE) Software | Analog DevicesADR4525 Datasheet and Product Info | Analog DevicesSDP-K1 Evaluation Board | Analog DevicesEVAL-AD5676RARDZ Evaluation Board | Analog DevicesSDP-K1 Evaluation Board | Analog Devices