Owner's Manual for MEAN WELL models including: ELG-75 Series, ELG-75 Series 48 75W Constant Voltage Plus Current LED Driver, 48 75W Constant Voltage Plus Current LED Driver, Constant Voltage Plus Current LED Driver, Voltage Plus Current LED Driver, Current LED Driver, LED Driver, Driver
Блок живлення для світлодіодів 2,5...5A, 10,8...13,2VDC, ELG-75-12A MeanWell за ціною від 839 грн - РКС Компоненти - РАДІОМАГ
File Info : application/pdf, 11 Pages, 1.60MB
DocumentDocumentE L G - 7 5 48~75W Constant Voltage + Constant Current LED Driver
series
User's Manual
IP65 IP67
IS 15885(Part 2/Sec13)
THOMAS SAMUEL
THOMAS SAMUEL
R-41027766
(Please refer safety description)
8
{
A
Dx
Downloaded from Arrow.com.
File Name:ELG-75-SPEC 2023-09-11
E L G - 7 5 48~75W Constant Voltage + Constant Current LED Driver
series
SPECIFICATION
MODEL
ELG-75-12
ELG-75-24
ELG-75-36
ELG-75-42
ELG-75-48
DC VOLTAGE
12V
CONSTANT CURRENT REGION Note.2 6 ~ 12V
RATED CURRENT
5A
200VAC ~ 305VAC
24V 12 ~ 24V 3.15A
36V 18 ~ 36V 2.1A
42V 21 ~ 42V 1.8A
48V 24 ~ 48V 1.6A
RATED POWER
60W Note.5 100VAC ~ 180VAC
75.6W
75.6W
75.6W
76.8W
OUTPUT
48W
60W
60W
RIPPLE & NOISE (max.) Note.3 150mVp-p
200mVp-p
250mVp-p
VOLTAGE ADJ. RANGE
Adjustable for A/AB-Type only (via built-in potentiometer)
10.8 ~ 13.2V
21.6 ~ 26.4V
32.4 ~ 39.6V
CURRENT ADJ. RANGE
Adjustable for A/AB-Type only (via built-in potentiometer)
2.5 ~ 5A
1.57 ~ 3.15A
1.05 ~ 2.1A
VOLTAGE TOLERANCE Note.4 ±3.0%
±3.0%
±2.5%
LINE REGULATION LOAD REGULATION
±0.5% ±2.0%
±0.5% ±1.0%
±0.5% ±1.0%
SETUP, RISE TIME Note.6 500ms, 100ms/115VAC, 230VAC
HOLD UP TIME (Typ.)
10ms/ 230VAC 10ms/ 115VAC(at full load)
VOLTAGE RANGE
100 ~ 305VAC 142 ~ 431VDC Note.5 (Please refer to "STATIC CHARACTERISTIC" section)
60W 250mVp-p
37.8 ~ 46.2V
0.9 ~ 1.8A ±2.5% ±0.5% ±0.5%
60W 250mVp-p
43.2 ~ 52.8V
0.8 ~ 1.6A ±2.0% ±0.5% ±0.5%
FREQUENCY RANGE POWER FACTOR
47 ~ 63Hz
PF0.97/115VAC, PF0.95/230VAC, PF0.92/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
TOTAL HARMONIC DISTORTION
THD< 20%(@load50%/115VC,230VAC; @load75%/277VAC) (Please refer to "TOTAL HARMONIC DISTORTION(THD)" section)
INPUT
EFFICIENCY (Typ.)
86%
88%
89%
90%
90%
AC CURRENT
0.7A / 115VAC 0.45A / 230VAC 0.38A/277VAC
INRUSH CURRENT(Typ.)
COLD START 50A(twidth=350s measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. No. of PSUs on 16A CIRCUIT BREAKER
5 units (circuit breaker of type B) / 8 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT
<0.75mA / 277VAC
NO LOAD / STANDBY POWER CONSUMPTION
No load power consumption <0.5W for Blank / A / Dx / D2-Type Standby power consumption <0.5W for B / AB / DA-Type
OVER CURRENT
SHORT CIRCUIT PROTECTION
OVER VOLTAGE
95 ~ 108%
Constant current limiting, recovers automatically after fault condition is removed
Hiccup mode, recovers automatically after fault condition is removed
14 ~ 18V
28 ~ 34V
41 ~ 48V
Shut down output voltage, re-power on to recover
47 ~ 54V
54 ~ 62V
OVER TEMPERATURE WORKING TEMP. MAX. CASE TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION
SAFETY STANDARDS
Shut down output voltage, re-power on to recover Tcase=-40 ~ +85 (Please refer to " OUTPUT LOAD vs TEMPERATURE" section) Tcase=+85 20 ~ 95% RH non-condensing -40 ~ +80, 10 ~ 95% RH ±0.03%/ (0 ~ 60)
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes UL8750(type"HL"), CSA C22.2 No. 250.13-12; IEC/BS EN/EN/AS/NZS 61347-1, IEC/BS EN/EN/AS/NZS 61347-2-13 independent, BS EN/EN62384;EAC TP TC 004;BISIS15885(for 12A/12DA/12B/24A/24B/24DA/36A/36B/42A/42B/48A/48B only); IP65 or IP67; GB19510.1, GB19510.14; KC61347-1,KC61347-2-13 approved
DALI STANDARDS
Compliance to IEC62386-101,102,(207 by request) for DA Type only
SAFETY & WITHSTAND VOLTAGE
I/P-O/P:3.75KVAC I/P-FG:2.0KVAC O/P-FG:1.5KVAC
EMC
ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH
EMC EMISSION
Compliance to BS EN/EN55015,BS EN/EN61000-3-2 Class C (@load50%) ; BS EN/EN61000-3-3; GB/T 17743, GB17625.1; EAC TP TC 020; KC KN15,KN61547
EMC IMMUNITY
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level (surge immunity Line-Earth 6KV, Line-Line 4KV);EAC TP TC 020; KC KN15,KN61547
MTBF
3451.7K hrs min. Telcordia SR-332 (Bellcore) 331.3Khrs min. MIL-HDBK-217F (25)
OTHERS DIMENSION
180*63*35.5mm (L*W*H)
PACKING
0.8Kg;16pcs/13.4Kg/0.67CUFT
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature. 2. Please refer to "DRIVING METHODS OF LED MODULE". 3. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 4. Tolerance : includes set up tolerance, line regulation and load regulation. 5. De-rating may be needed under low input voltages. Please refer to "STATIC CHARACTERISTIC" sections for details. 6. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time. 7. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
(as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf) 8. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 70 or less. 9. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com 10. The ambient temperature derating of 3.5/1000m with fanless models and of 5/1000m with fan models for operating altitude higher than 2000m(6500ft). 11. For any application note and IP water proof function installation caution, please refer our user manual before using.
https://www.meanwell.com/Upload/PDF/LED_EN.pdf Product Liability Disclaimer: For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
Downloaded from Arrow.com.
File Name:ELG-75-SPEC 2024-01-08
E L G - 7 5 48~75W Constant Voltage + Constant Current LED Driver
series
Block Diagram
EMI FILTER
I/P
&
RECTIFIERS
PFC CIRCUIT
POWER SWITCHING
O.T.P.
O.L.P.
PWM & PFC CONTROL
CASE :Protective Earth
RECTIFIERS &
FILTER
PFC fosc : 50~120KHz PWM fosc : 60~130KHz
Vo+ VoO.L.P.
DETECTION CIRCUIT
O.V.P.
DRIVING METHODS OF LED MODULE
This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs.
100
Vo(%)
50 (min.)
(A) Constant
Voltage area
(B) Constant Current area
(C) Hiccup Protection
50
100
Io(%)
Typical output current normalized by rated current (%)
In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL.
Downloaded from Arrow.com.
File Name:ELG-75-SPEC 2024-01-08
E L G - 7 5 48~75W Constant Voltage + Constant Current LED Driver
series
DIMMING OPERATION
AC/N(Blue) AC/L(Brown)
ELG-75
DIM+(Purple)* DIM-(Pink)** Vo-(Black) Vo+(Red)
3 in 1 dimming function (for B/AB-Type)
Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal or resistance.
Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100A (typ.)
* DIM+ for B/AB-Type DA+ for DA-Type PROG+ for D2-Type
* *DIM- for B/AB-Type DA- for DA-Type PROG- for D2-Type
Applying additive 0 ~ 10VDC
100%
90%
Vo+ +
80%
+
70%
Output current (%)
Vo-
60%
-
50%
DIM+ +
40%
Additive Voltage
30%
-
20%
DIM-
10%
"DO NOT connect "DIM- to Vo-"
0% 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V
Dimming input: Additive voltage
Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
Vo+ +
+
Vo-
-
DIM+
Additive PWM signal DIM-
"DO NOT connect "DIM- to Vo-"
Output current (%)
100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0%
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input
Applying additive resistance:
100%
Output current (%)
Vo+ +
VoDIM+
90%
+
80%
70%
-
60%
50%
40%
Additive Resistance
30%
DIM-
20%
"DO NOT connect "DIM- to Vo-"
10%
0% Short 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N
(N=driver quantity for synchronized dimming operation)
Dimming input: Additive resistance
Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%.
2. The output current could drop down to 0% when dimming input is about 0k or 0Vdc, or 10V PWM signal with 0% duty cycle.
File Name:ELG-75-SPEC 2024-01-08
Downloaded from Arrow.com.
E L G - 7 5 48~75W Constant Voltage + Constant Current LED Driver
series
DALI Interface (primary side; for DA-Type) Apply DALI signal between DA+ and DA-. DALI protocol comprises 16 groups and 64 addresses. First step is fixed at 8% of output.
Smart timer dimming function (for Dxx-Type by User definition) MEAN WELL Smart timer dimming primarily provides the adaptive proportion dimming profile for the output constant current level to perform up to 14 consecutive hours. 3 dimming profiles hereunder are defined accounting for the most frequently seen applications. If other options may be needed, please contact MEAN WELL for details.
Ex : D01-Type: the profile recommended for residential lighting
Set up for D01-Type in Smart timer dimming software program:
T1
T2
T3
T4
TIME**
06:00
07:00
11:00
---
LEVEL** 100%
70%
50%
70%
Dimming Level(%)
Operating Time(HH:MM)
**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level. Example: If a residential lighting application adopts D01-Type, when turning on the power supply at 6:00pm, for instance:
[1] The power supply will switch to the constant current level at 100% starting from 6:00pm. [2] The power supply will switch to the constant current level at 70% in turn, starting from 0:00am, which is 06:00 after the power supply turns on. [3] The power supply will switch to the constant current level at 50% in turn, starting from 1:00am, which is 07:00 after the power supply turns on. [4] The power supply will switch to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on.
The constant current level remains till 8:00am, which is 14:00 after the power supply turns on.
Ex: D02-Type: the profile recommended for street lighting
Set up for D02-Type in Smart timer dimming software program:
TIME** LEVEL**
T1 01:00 50%
T2 03:00 80%
T3 8:00 100%
T4
T5
11:00
---
60%
80%
Dimming Level(%)
Operating Time(HH:MM) **: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level. Example: If a street lighting application adopts D02-Type, when turning on the power supply at 5:00pm, for instance: [1] The power supply will switch to the constant current level at 50% starting from 5:00pm. [2] The power supply will switch to the constant current level at 80% in turn, starting from 6:00pm, which is 01:00 after the power supply turns on. [3] The power supply will switch to the constant current level at 100% in turn, starting from 8:00pm, which is 03:00 after the power supply turns on. [4] The power supply will switch to the constant current level at 60% in turn, starting from 1:00am, which is 08:00 after the power supply turns on. [5] The power supply will switch to the constant current level at 80% in turn, starting from 4:00am, which is 11:00 after the power supply turns on. The
constant current level remains till 6:30am, which is 14:00 after the power supply turns on.
File Name:ELG-75-SPEC 2024-01-08
Downloaded from Arrow.com.
E L G - 7 5 48~75W Constant Voltage + Constant Current LED Driver
series
Ex: D03-Type: the profile recommended for tunnel lighting
Set up for D03-Type in Smart timer dimming software program:
T1
T2
T3
TIME**
01:30
11:00
---
LEVEL** 70%
100%
70%
Dimming Level(%)
Operating Time(HH:MM)
**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level. Example: If a tunnel lighting application adopts D03-Type, when turning on the power supply at 4:30pm, for instance: [1] The power supply will switch to the constant current level at 70% starting from 4:30pm. [2] The power supply will switch to the constant current level at 100% in turn, starting from 6:00pm, which is 01:30 after the power supply turns on. [3] The power supply will switch to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on. The constant current level remains till 6:30am, which is 14:00 after the power supply turns on.
Downloaded from Arrow.com.
File Name:ELG-75-SPEC 2024-01-08
LOAD (%)
E L G - 7 5 48~75W Constant Voltage + Constant Current LED Driver
series
OUTPUT LOAD vs TEMPERATURE(Note.9)
100
80 230VAC input only
60
40
20
-40
-25 -10 0
15
30
50
60
70 (HORIZONTAL)
AMBIENT TEMPERATURE,Ta ()
LOAD (%)
100
80 230VAC input only
60
40
20
-40 -25 0
20
45
55
65
75
85 (HORIZONTAL)
Tcase ()
STATIC CHARACTERISTIC
100 90 80 70 60 50 40
100 120 140 160 180 200 240 250 260 270 280 305
INPUT VOLTAGE (V) 60Hz De-rating is needed under low input voltage.
PF
POWER FACTOR (PF) CHARACTERISTIC
Tcase at 75 Constant Current Mode
1
0.95
0.9
0.85
0.8
0.75
0.7
277V
0.65
0.6
230V
0.55
0.5
115V
0.45
0.4
0.35
0.3
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
LOAD
TOTAL HARMONIC DISTORTION (THD)
48V Model, Tcase at 75
18% 16% 14% 12% 10%
277V75W 8%
230V75W 6%
115V60W 4% 2% 0%
50% 60% 70% 80% 90% 100%
LOAD
EFFICIENCY(%)
EFFICIENCY vs LOAD
ELG-75 series possess superior working efficiency that up to 90% can be reached in field applications. 48V Model, Tcase at 75
92 90 88 86 84 82 80 78 76 74 72 70
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
277V75W 230V75W 115V60W
LOAD
File Name:ELG-75-SPEC 2024-01-08
THD LOAD (%)
Downloaded from Arrow.com.
E L G - 7 5 48~75W Constant Voltage + Constant Current LED Driver
series
LIFETIME
LIFETIME(Kh)
120
100
80
60
40
20
0
20
30
40
50
60
70
80
90
Tc a s e ()
Downloaded from Arrow.com.
File Name:ELG-75-SPEC 2024-01-08
E L G - 7 5 48~75W Constant Voltage + Constant Current LED Driver
series
Mechanical Specification
Blank-Type
CASE NO.: 243A Unit:mm
180 169
300±20
156
300±20
63
45.8
AC/N(Blue) AC/L(Brown)
SJOW 17AWGx2C &H05RN-F 1.0mm2
85 tc
4-4.5
tc : Max. Case Temperature
20
SJOW 17AWGx2C &05RN-F 1.0mm2
Vo-(Black) Vo+(Red)
35.5
35
A-Type
180 169
300±20
156
AC/N(Blue) AC/L(Brown)
SJOW 17AWGx2C &H05RN-F 1.0mm2
85 tc
4-4.5
tc : Max. Case Temperature
20
45.8
63
300±20
SJOW 17AWGx2C &05RN-F 1.0mm2
Vo-(Black) Vo+(Red)
35.5
35
21
Downloaded from Arrow.com.
30.25 44.25
File Name:ELG-75-SPEC 2024-01-08
E L G - 7 5 48~75W Constant Voltage + Constant Current LED Driver
series
AB-Type
180 169
300±20
156
AC/N(Blue) AC/L(Brown)
SJOW 17AWGx2C &H05RN-F 1.0mm2
85 tc
4-4.5
tc : Max. Case Temperature
20
45.8
63
300±20
UL2517 20AWGx2C
SJOW 17AWGx2C &05RN-F 1.0mm2
DIM+(Purple) DIM-(Pink) Vo-(Black) Vo+(Red)
35.5
35
21
30.25 44.25
B/DA/D2-Type
180 169
300±20
156
AC/N(Blue) AC/L(Brown)
SJOW 17AWGx2C &H05RN-F 1.0mm2
85 tc
4-4.5
tc : Max. Case Temperature
20
45.8
63
300±20
UL2517 20AWGx2C
SJOW 17AWGx2C &05RN-F 1.0mm2
DIM+(Purple)* DIM-(Pink)** Vo-(Black) Vo+(Red)
* DIM+ for B-Type DA+ for DA-Type PROG+ for D2-Type
* *DIM- for B-Type DA- for DA-Type PROG- for D2-Type
35.5
35
Downloaded from Arrow.com.
File Name:ELG-75-SPEC 2024-01-08
E L G - 7 5 48~75W Constant Voltage + Constant Current LED Driver
series
3Y Model (3-wire input)
180 169
300±20
156
20 45.8 63
AC/N(Blue) AC/L(Brown) PE (Green/Yellow)
SJOW 17AWGx3C &H05RN-F 1.0mm2
85 tc
4-4.5
tc : Max. Case Temperature
Note1: Please connect the case to PE for the complete EMC deliverance and safety use. Note2: Please contact MEAN WELL for input wiring option with PE.
SJOW 17AWGx2C &05RN-F 1.0mm2
Recommend Mounting Direction
INSTALLATION MANUAL
Please refer to:http://www.meanwell.com/manual.html
Downloaded from Arrow.com.
File Name:ELG-75-SPEC 2024-01-08
MEAN WELL Switching Power Supply Manufacturer