Compliance proofs for products: LANCOM Systems GmbH
User Guide for LANCOM models including: LX-6500, LX-6500E, Indoor Access Points, LX-6500 Indoor Access Points, Access Points
LANCOM LX-6500 – the VIP Wi-Fi experience: LANCOM Systems GmbH
2022-08-01 — Power supply. 12 V DC, external power adapter (110 V or 230 V) or PoE based on 802.3bt via ETH1. Environment. Temperature range 0–40 °C;.
File Info : application/pdf, 1 Pages, 558.46KB
DocumentDocument111983/0622 LED description & technical details owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their Hardware Quick Reference LANCOM LX-6500 LANCOM LX-6500E 2.5G 2.5G Config (Com) Reset DC 12 V ETH2 ETH1 (PoE) USB Serial interface You can optionally configure the device by connecting it to a PC with a configuration cable (separately available). Reset button Pressed up to 5 seconds: device restart RESET Pressed longer than 5 seconds: configuration reset and device restart Power In case the power supply of the device should not be done via the PoE interface, please use only the optionally available plug-in power supply. Ethernet interfaces Use the cable with the Ethernet connectors to connect interface ETH1 (PoE) or ETH2 to your PC or a LAN switch. USB interface Connect compatible USB devices either directly to the USB interface, or use a suitable USB cable. Mounting & connecting Power Off Green, permanently* Blue / red, alternatingly blinking 1x green inverse blinking* 2x green inverse blinking* 3x green inverse blinking* Purple, blinking Purple, permanently Yellow / green, blinking alternating with WLAN Link LED Device switched off Device operational, resp. device paired / claimed and LANCOM Management Cloud (LMC) accessible. DHCP error or DHCP server not accessible (only when configured as DHCP client) Connection to the LMC active, pairing OK, claiming error. Pairing error, resp. LMC activation code / PSK not available. LMC not accessible, resp. communication error. Firmware update Device booting The access point searches for a WLAN controller WLAN Link Off Green, permanently Green, inverse flashing Green, blinking Red, blinking Yellow / green, blinking alternating with power LED No Wi-Fi network defined or Wi-Fi module deactivated. The Wi-Fi module is not transmitting beacons. At least one Wi-Fi network defined and Wi-Fi module activated. The Wi-Fi module is transmitting beacons. Number of flashes = number of connected Wi-Fi stations DFS scanning or other scan procedure Wi-Fi module hardware error The access point searches for a WLAN controller Hardware Power supply Environment Housing Number of fans 12 V DC, external power adapter (110 V or 230 V) or PoE based on 802.3bt via ETH1 Temperature range 040 °C; Access point overheating is avoided by automatic throttling of the Wi-Fi modules. Humidity 0-95 %; non-condensing Robust synthetic housing, rear connectors, ready for wall and ceiling mounting, measures 230 x 42 x 230mm (W x H x D) None; fanless design, no rotating parts, high MTBF Wi-Fi Frequency band Radio channels 2.4 GHz Radio channels 5 GHz Radio channels 6 GHz Antennas 2,4002,483.5 MHz, 5,1805,700 MHz, 5,945-6,425 MHz. Country-specific restrictions possible. Up to 13 channels, max. 3 non-overlapping (2.4 GHz band) Up to 19 non-overlapping channels (automatic dynamic channel selection required) Up to 24 non-overlapping channels (EU/ETSI) Integrated Other radio technologies BLE Bluetooth Low Energy 5.1 Wireless ePaper (only LX-6500E) Interfaces ETH1 (PoE) ETH2 Serial interface The device is equipped with a radio module for controlling LANCOM Wireless ePaper displays in the 2.4 GHz frequency band. 10 / 100 / 1000 / 2.5G Base-T; PoE adapter compliant to IEEE 802.3bt required 10 / 100 / 1000 / 2.5G Base-T Serial configuration interface / COM-port (8-pin mini-DIN): 115,000 baud Package content Cable Bracket Ethernet cable, 3 m Bracket for wall and ceiling mounting and/or omissions. Cloud-ready Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide! Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times. Please observe the following when setting up the device i The power plug of the device must be freely accessible. Do not rest any objects on top of the device. Keep all ventilation slots on the side of the device clear of obstruction. Lockable wall and ceiling mounting with the supplied LANCOM Wall Mount LX-6500 Please note that support service for third-party accessories is excluded. *) The additional power LED statuses are displayed in 5-seconds rotation if the device is configured to be managed by the LANCOM Management Cloud. The product contains separate components which, as so-called open source software, are subject to their own licenses, in particular the General Public License (GPL). The license information for the device firmware (LCOS LX) can be found via the command line with the command ,,show 3rd-party-licenses". If required by the respective license, source files for the affected software components are provided on request. For this purpose, please contact us via e-mail at gpl@lancom.de. Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with Directives 2014/30/EU, 2014/53/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of Conformity is available at the following Internet address: www.lancom-systems.com/doc