Visual Reinforcement Audiometry VRA Equipment
User Manual for FLEX VRA models including: YI5-USB01, YI5-USB01 USB Receiver, USB Receiver, Receiver
Celadon, Inc. USB01 YI5-USB01 YI5USB01 usb01
File Info : application/pdf, 3 Pages, 335.45KB
DocumentDocumentUser Manual Copyright 2024 Lab-T, Inc. Regulatory Compliance Statements FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Interference Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Industry Canada Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Ce dispositif est conforme à la norme CNR d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionne ment est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Tout changement ou modification non expressément approuvé par la partie chargée de la mise en conformité peut annuler le droit de l'utilisateur à utiliser l'équipement. ·Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour unenvironnement non contrôlé. IC : 9065A-USB01 Flex VRA USB Receiver User's Manual FCC Caution Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. · This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. FCC ID: YI5-USB01 Flex VRA 100 E. Whitestone Blvd. St. 148, #160 Cedar Park, TX 78613 flexvra.com Model: Flex-USB-1 About this guide This guide explains the setup and operation of Flex VRA USB receiver, P/N Flex-USB-1. Package Contents The package contains the remote and the USB receiver. Button Location Button Description Pairing Pairing to VRA remote control Attempted Use Receiver Not Paired - User pushes a button on the VRA remote control. ; Non action. - User pushes a button on the USB receiver. ; RED LED on the USB receiver blinks to pair with the VRA remote control. (timeout = 60secs) Overview Flex wireless receiver device for receiving a 433.92 MHz (FSK) signal from wireless controller and sending HID data to a PC during Visual Reinforcement Audiometry (VRA) testing. Flex VRA System Operation 1 System = 3 PCs with receiver 433.92MHz PC (Audiometry Software) HID data Flex-USB-1 Flex-Remote-1 Pairing the USB Receiver To pair the USB receiver with the VRA remote control · Press the pairing button on the USB receiver once. · Red Feedback LED of the USB receiver turns ON and flashes. (timeout = 60secs) · Press and Hold the Light On button and Lights Only button of the VRA remote control for 3 seconds. · USB receiver accepts the remote pairing request. · Green Feedback LED blinks one time (slowly), turns OFF and the USB receiver exits pairing mode. · USB receiver is now paired to the VRA remote control. Un-Pairing Process To un-pair the USB receiver with the VRA remote control · Press and Hold the pairing button on the USB receiver for 3 seconds. · RED feedback LED blinks 5 times (slowly). · USB receiver is now un-paired to the VRA remote control. Normal Use Receiver Paired - User pushes a button on the VRA remote control. ; GREEN LED on the USB receiver blinks for the duration of the VRA remote control button being held down. - User pushes a button on the USB receiver. ; RED LED on the USB receiver 5 times (fast)