Home Page-UE Technology Corporation
Instruction Manual for AUGE LIGHT models including: NN Magi Sensor Lamp, NN, Magi Sensor Lamp, Sensor Lamp, Lamp
2 giorni fa — If the environment is dark, the device will automatically turn on when someone passes by. If someone passes by during the lighting-up period, the light will ...2 pagine
File Info : application/pdf, 2 Pages, 1.15MB
DocumentDocumentNN
MAGI SENSOR
*The appearance and technology of this product are protected by patents.
NN
Product description
We suggest that you read this manual before using the product in order to better understand its features and functions. Please keep this manual safe for future reference.
Holder
Type-C Charging Port
1 sensor mode light 3 Infrared Sensor
2 Power Button 4 Base
5 LED light source
6 Lamp shade
7 Magnetic bead
Operating Instructions
1.When you press the switch button, the device enters the light detection & human sensing mode.
If the environment is dark, the device will automatically turn on when someone passes by. If someone passes by during the lighting-up period, the light will continue to stay on. If no one passes by within 25 seconds, the light will automatically turn off. The sensing distance of the mode is 2 meters, and the sensing angle is 120°. Please note that this mode only works in relatively dark environments, and the light will only be triggered if there is someone passing by in the dark.
2.Press the button a second time to enter constant light mode:
When press second time, the filament will stay constantly lit, and the indicator light will turn off. By default, the brightness is set to 50% when powered on. Press and hold the button to increase the brightness to its maximum level (and then decrease it). Press and hold the button again to reduce the brightness to its minimum level. If you release the button during the brightness adjustment process, the light will remember the current brightness level. The light will maintain this level the next time you turn on the sensing mode or the constant light mode.
3.Press the button a third time to turn off the light.
NN
installation instructions
1.First, wipe the surface of the lamp installation platform clean and keep it dry.
2.Tear off the 3M adhesive from the bottom of the fixture holder.
3.Install the fixture holder on the platform surface, gently press the fixture holder to make it tightly adhere to the platform surface.
Note: The fixture holder should be installed horizontally or vertically.
Note: After installing the fixture holder, please let it stand still for 3-5 minutes before placing the lamp.
Correct placement Incorrect placement
4.Place the lamp on the fixture holder to complete the installation.
As shown in the figure below, this product can be installed in either a vertical or horizontal position.
1
2
3
4
Basic parameters
Name: Fila Sensor Rated input: 5.0V---1A Power: 1W Weight: 160±16g Size: 35*35*260mm Material: Organic Glass
Brightness: 80lm Color temperature: 2200K Battery capacity: 800mAH Sensing angle: 120° Sensing distance: 1.5-2m Charging interface: Type-C
1 Disconnected
2 Normal connected
1.This product is a new type of LED filament lamp with a magnetic bead. The detachment of the magnetic beads and magnet duringtransportation (as shown in Figure 1) is a normal phenomenon.
2.If the filament is twisted (as shown in Figure 1), it can be manually reset by holding the lamp in your hand and shaking it left and right. Using the strong magnet at the bottom, the filament can be Using the and reset successfully (as shown in Figure 2).
Power indicator light
Power indicator light
During the charging process, the indicator light will turn yellow. When charging is complete, the indicator light will turn green.
This product is powered by a polymer lithium battery, which takes approximately 2 hours to fully charge. It can work continuously for 11 hours and has a standby time of up to 2 months. For the initial use, if you find that the indicator light or light does not turn on, please use a 5V charger to charge the product.
Emailsales@augelight.com Webwww.augelight.com
Guarantee Card
Product Name: Date of Purchase: Product Color: Purchasing Region:
Name: Phone: Email: Address:
PS
NN
*
NN
Type-C
1 3 5 LED
7
2 4
6
1.,+ + 25 2 120°
2., 50%
3.
NN
1. 2.3M
3.
:
:30
5.0V---1A 1W 160±16g 35*35*260mm PC
50lm 2700K 800mAH 120° 1.5-2m Type-C
1
2
4.
1
2
3
4
1.LED (1)
2.(1) (2)
: ; :
1. 2 112, 5V 2. 25S
sales@augelight.com www.augelight.com