KICKER PXIBT100.2 Stereo Integrated Amplifier

Introduction

This manual provides information for the KICKER PXIBT100.2 Stereo Integrated Amplifier, designed as an amplified controller for Bluetooth® devices.

The manual is available in multiple languages, including English, Spanish, German, and French.

Important Safety Warning

WARNING: PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER IN A DISTORTED OR CLIPPED MANNER CAN CAUSE YOUR AUDIO SYSTEM TO OVERHEAT, POSSIBLY CATCHING FIRE AND RESULTING IN SERIOUS DAMAGE TO YOUR COMPONENTS AND/OR VEHICLE. KICKER PRODUCTS ARE CAPABLE OF PRODUCING SOUND LEVELS THAT CAN PERMANENTLY DAMAGE YOUR HEARING! TURNING UP A SYSTEM TO A LEVEL THAT HAS AUDIBLE DISTORTION IS MORE DAMAGING TO YOUR EARS THAN LISTENING TO AN UNDISTORTED SYSTEM AT THE SAME VOLUME LEVEL. THE THRESHOLD OF PAIN IS ALWAYS AN INDICATOR THAT THE SOUND LEVEL IS TOO LOUD AND MAY PERMANENTLY DAMAGE YOUR HEARING. PLEASE USE COMMON SENSE WHEN CONTROLLING VOLUME.

Performance Specifications

Pro Tip: To get the best performance from your new KICKER Amplifier and extend the warranty by 1 year, use genuine KICKER accessories and wiring.

Installation

Mounting

Choose a structurally sound location to mount your KICKER PXIBT100.2. Ensure there are no items behind the mounting area. Select a location that allows at least 4 inches (10cm) of open ventilation for the amplifier. Drill four holes using a 7/64" (3mm) bit and use the supplied #8 screws to mount the amplifier. Mount the unit behind the fairing, underneath the seat, or in another secure location isolated from weather.

Diagram Description: Illustration showing the KICKER PXIBT100.2 unit with mounting holes, indicating it should be mounted using the included screws.

Remote Mounting

The remote bar mounting clamp can be installed on either the left or right side on the back of the remote.

Use the included remote mounting plate for a custom, flush installation. Exercise caution to avoid drilling into wiring or vehicle mechanisms. You are responsible for the safe and secure mounting of the unit and remote. A cut-out template is provided to assist with installation.

Diagram Description: Illustration showing the remote mounting clamp and plate. It indicates the clamp can be attached to either side of the remote. Dimensions are provided: Width: 86mm, Height: 41mm, Depth: 18mm. It also shows a 1m cable and mentions using the included 1.5m remote extension cable if necessary.

Wiring

Disconnect the vehicle's battery to prevent electrical shorts. Connect the PXIBT harness to the amplifier. A good ground connection is crucial. For motorcycles, extend the ground wire to the battery. Install a 15A fuse in the yellow +12V constant wire, within 18 inches (45cm) of the battery and in-line with the harness' power cable. When removing the amplifier, disconnect the ground wire last.

Diagram Description: Illustration of the PXIBT100.2 unit with its wiring harness. The harness includes wires for: +12V Constant (yellow), +12V Ignition (red), Remote turn-on out (blue), Ground (black). It also shows RCA outputs (red and white), a 3.5mm aux input, and connections labeled L+, L-, R+, R- for speakers (2 or 4 ohm).

Operation

Crossover Switches

Use the HI-PASS switches located behind the rubber protective cover to set the internal crossover frequency. Options include OFF, 60Hz, 80Hz, or 120Hz, depending on the configuration of switches 1 and 2. Do not change switches while the audio system is on.

Music Playback

The PXIBT100.2 receives audio via Bluetooth, 3.5mm AUX input, and USB input. The USB input supports MP3 and WMA file formats.

Bluetooth Pairing: The unit enters Bluetooth pairing mode on first use. To re-enter pairing mode, press and hold the PLAY-PAUSE button until the Bluetooth LED flashes blue rapidly. On your audio device, enable discovery mode and select 'KICKER PXIBT'. A solid blue Bluetooth icon indicates a successful connection. A slow flashing blue icon means the unit is paired but not connected.

Input Selection and Controls

Briefly press the POWER button to cycle through Bluetooth, AUX, and USB input modes. The unit remembers the last selected mode. You can press and hold the POWER button to turn the unit ON/OFF. It is recommended to wire the RED (+12V Ignition) wire through a switched accessory to turn the unit ON/OFF with the vehicle.

Brightness Control: Press and hold the Track button for 5 seconds. The volume buttons will then control the LED brightness (0-10). The unit exits brightness mode after 5 seconds of inactivity.

Input Status LEDs:

• B/T - Slow Flash: Paired; no connection
• B/T - Rapid Flash: Pairing mode
• B/T - Solid: Bluetooth Connected

Diagram Description: Illustration of the control panel layout. Buttons are labeled: Volume (+/-) for audio and brightness control, Track (forward/backward), Power/Source Select. LED status indicators are shown. Control functions are described: Volume buttons adjust brightness up/down when in brightness mode. Short press on the center button acts as PLAY-PAUSE. Press and hold the center button enters PAIRING MODE. The POWER button is for OFF/ON and SOURCE SELECTION (Bluetooth/AUX/USB). Notes indicate Bluetooth range up to 30ft.

Troubleshooting

If the PXIBT100.2 is not functioning, check for blown fuses, incorrect wiring, or improper switch/gain settings. A Power Protection LED indicates the unit's status (Red for issues, Blue for normal operation).

• Blue LED off, no output: Check +12V power terminal, remote turn-on terminal, power/ground connections, and ground terminal conductivity using a Volt Ohm Meter (VOM).
• Blue LED on, no output: Check RCA connections, test speakers with a known good speaker, substitute the source unit, and check for RCA signal with a VOM.
• Protection LED flashing with loud music: Indicates low battery voltage. Check vehicle charging system connections, battery, or alternator.
• Protection LED on, no output: If the amplifier is very hot, thermal protection is engaged. Check speaker impedance and airflow. If the unit shuts down while the vehicle is running, voltage protection is engaged; check the vehicle's charging system (10-16V operating range). If the amplifier plays only at low volume, short circuit protection is engaged; check speaker wires for shorts or damaged speakers.
• No or low output: Check source unit balance control and speaker output connections.
• Alternator noise-whining sound: Check 3.5mm cable for damage and routing. Adjust gain settings if too high.
• Reduced bass response: Reverse speaker connections (positive/negative) to check for phase issues.

CAUTION: Ensure correct connections when jump-starting a vehicle to prevent blown fuses or damage to other systems.

For further assistance, contact an Authorized KICKER Dealer or visit www.kicker.com. Technical support is available via email at support@kicker.com or by phone at (405) 624-8583.

Diagram Description: A warning symbol (sun with a line through it) is shown, likely indicating a caution against heat or direct sunlight exposure.

Warranty Information

KICKER warrants this product against defects in material and workmanship for TWO (2) YEARS from the original purchase date. A THREE (3) MONTH warranty applies to refurbished or B Goods. The original receipt is required for all warranty claims.

What is not covered: Improper installation, damage from moisture/heat, negligence, misuse, accident, abuse, amplifier clipping/distortion, unauthorized repairs, tampered labels/serial numbers, returns without RMA, unauthorized dealers, freight damage, or shipping costs.

Service: Return defective merchandise to your local Authorized KICKER Dealer or contact Stillwater Designs for a Return Merchandise Authorization (RMA) number.

Compliance Information

FCC CAUTION: This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: it may not cause harmful interference, and it must accept any interference received.

IC CAUTION: Complies with Industry Canada license-exempt RSS standard(s). Operation is subject to two conditions: no harmful interference, and acceptance of any interference.

RF Exposure statements for FCC and IC are included, indicating compliance with radiation exposure limits and recommending minimum installation distances.