M8 Wireless Earphones

Product Specifications

Note: All technical information is subject to true performance.

Instructions for Use

To protect and extend the service life of the charging case and headphones, please fully charge the charging case and headphones before first use.

Headphone Charging

Place the headphones into the charging case and close the lid. The white LED running light on the charging case indicates that charging is in progress. The light will turn off when the headphones are fully charged.

Diagram Description: An illustration shows the left and right earphones being placed inside the charging case. The charging case has a white LED light that illuminates during charging.

Charging Case Charging

Use a Type-C charging cable to connect the charging case to a charger. The white LED running light on the charging case indicates that charging is in progress. The light will turn off when the charging case is fully charged.

Diagram Description: An illustration shows a Type-C cable connected to the charging port of the charging case. The case features a white LED light that indicates charging status.

Headphones Touch Commands

The touch point is located in the concave circle on the upper part of the headphone.

LED Indicators

Pairing

Open the charging case and take out both headphones. The headphones will power on automatically and enter pairing mode after 5 seconds. You will hear the L/R voice prompt "beep" simultaneously, indicating successful connection. Open your Bluetooth device and search for "M8" to connect. You will hear the voice prompt "connected".

Pairing Troubleshooting

If pairing fails, you may find two "M8" pairing names in your device. To resolve this, put both headphones back into the charging case, close the charging case lid, then reopen the charging case lid and wait for 5 seconds. You should then find only one "M8" pairing name in your device. Reconnect your device.

Troubleshooting and Tips

Ensure Both Headphones Are Connected

If only one headphone can hear sound, please check if both headphones are powered on. The other headphone might have low battery or be turned off. Charge the headphones, then power them on. You can either pick up the headphones from the charging case to power on automatically or press and hold the power button until the headphones turn on.

Ensure the Charging Case Has Sufficient Power

When the charging case has low battery or no battery, the headphones may not be recognized when placed into the charging case, which could cause them to continue working outside the case.

Check Charging Points

If the charging points of the headphones are covered by debris or other material, the charging case may be unable to charge the headphones. Please try removing any obstruction or wiping the charging points with alcohol. Clean and try charging again.

Environmental Information

This product may contain substances hazardous to the environment or human health if not disposed of properly. Electrical and electronic equipment should not be disposed of in regular municipal waste but must be collected separately for proper treatment. The crossed-out bin symbol [?️] on the product reminds you of the need for proper disposal at the end of its life. This helps prevent improper treatment of substances, which could be hazardous to the environment or human health. It also aids in the recovery, recycling, and reuse of materials. Manufacturers and distributors provide collection and treatment systems for these products. Contact your distributor for information on collection arrangements at the end of the product's life. Distributors may also inform you about free disposal of equivalent old equipment when purchasing a new product, or if the old product is smaller than 25 cm.

Disposal contrary to these guidelines may result in penalties according to national provisions. We also recommend adopting further environmental protection measures, such as recycling packaging and properly disposing of used batteries [?]. Your help is crucial in reducing the use of natural resources, minimizing landfill waste, and improving quality of life by preventing hazardous substances from entering the environment.

[♻️] Reduce | Reuse | Recycle

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.