Instruction Manual for DOOYA models including: DD1538H, VYYDD1538H, DD1536H, DD1536H DD1538H Solar Station With Integrated Receiver, DD1536H DD1538H, Solar Station With Integrated Receiver, Station With Integrated Receiver, Integrated Receiver, Receiver, Station
NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. DD1538H Outdoor solar panel VYYDD1538H VYYDD1538H dd1538h
" Wireless shielding mode Additional function Setting button×6s Run for hint×2 Release button " Reset to factor mode Additional function Setting button×14s Run for hint×4 Release button " Installation Method Additional function Installation position 1Side Mounting Short press the setting button on the receiver to restore the wireless reception function. Red LED flashes twice OK Enter the wireless shielding mode, turn off the wireless reception function. Red LED flashes four times OK Reset to factory mode successfully Install the bracket as shown in the figure Correct installation method Wrong installation method Installation position 2Top Mounting Install the bracket as shown in the figure Correct installation method Wrong installation method DD1536H/DD1538H Solar Station With Integrated Receiver Specification Version NO.: A/02 5 Product description Technical support DM35DS-10N/9R DM35DS-13N/13R DM45DS-20N/10R DD1536H DM35DS-10N/9R DM35DS-13N/13R DM45DS-20N/10R DM45DS-50N/5R DM45DS-50N/12R DD1538H Stall protection function Low power consumption sleep mode Output voltage: 9.5V~12.6V Working temperature-15 ~ 55 DD1536H Maximum output power: 80W Size: 400mm×50mm DD1538H Maximum output power: 90W Size: 580mm×50mm Can use the MICRO USB 5V Android charging line One DD1536H/DD1538H can store maximum 10 emitter channels. If there are already 10 channels, it will take turns to cover former channels from last one if adding more channels. When emitter is under group control, match code will be invalid. The motor works continuously for 4 minutes and then stops automatically. 5 Matchable emitter Technical support 5 Control range Technical support DD1536H/ DD1538H Motorized roller shutter L1 Effective transmitting distancemay have deviation due to actual environment Motorized DD1536H/ roller shutter DD1538H DD1600H Single-channel emitter DD1602H 15-channel emitter 5 Button specification Technical support Motor Interface DD1800H Single-channel emitter L2 L1 open L2 partition 9.5V~12.6V 200m 35m Reception frequency 433.92MHz After connect to USB, when the battery voltage is higher than 12V, the green LED indicator is always bright. After connect to USB, when the battery voltage is higher than 10.2V~12V,the green LED indicator light flashes; When the battery voltage is less than 10.2V, the red LED indicator flashes 10 times, indicating low voltage. LED indicator light (red light indicator function, green light indicates charging status) Charger jack Stroke button RF exposure statement This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. " Add emitter Additional function Method one Setting button×2s Run for hint×1 Red LED always bright once During the settings, the time between two operation must be shorter than 10s, otherwise it will quit the setting. Release button Stop button×2s Run for hint ×2, Red LED flashes×3 OK Success add emitter Method two P2×1 Run for hint ×1, Red LED flashes×1 P2×1 During the settings, the time between two operation must be shorter than 10s, otherwise it will quit the setting. Emitter is the one already matched code, while emitter has not, need to add. Stop button×2s Run for hint ×1, Red LED flashes×1 Run for hint ×2 ,Red LED flashes×3 OK Success add emitter Method three P2×1 Run for hint ×1, Red LED flashes×1 P2×1 Run for hint ×1, Red LED flashes×1 During the settings, the time between two operation must be shorter than 10s, otherwise it will quit the setting. Emitter is the one already matched code, while emitter has not, need to add. P2×1 Run for hint ×2, Red LED flashes×3 OK Success add emitter " Switch Direction Additional function Method one (Up button+ down button)×2s Within 30 seconds after the setting up or add emitter Run for hint×1 Method two Setting button×10s Run for hint×3 Release button Release button Red LED flashes three times OK Success switch direction OK Success switch direction " Delete one emitter Additional function Method one Setting button×2s Run for hint×1 Red LED always bright once During the settings, the time between two operation must be shorter than 10s, otherwise it will quit the setting. Release button Stop button×2s Run for hint ×2, Red LED flashes×3 OK Success delete emitter Method two P2×1 Run for hint ×1, Red LED flashes×1 P2×1 Run for hint ×1, Red LED flashes×1 During the settings, the time between two operation must be shorter than 10s, otherwise it will quit the setting. Emitter and are already matched code, while emitter has need to delete. P2×1 Run for hint ×2, Red LED flashes×3 OK Success delete emitter " Delete all emitters Additional function P2×1 Stop button×1 Run for hint ×1, Red LED flashes×1 Run for hint ×1, Red LED flashes×1 P2×1 During the settings, the time between two operation must be shorter than 10s, otherwise it will quit the setting. Run for hint ×2, Red LED flashes×3 OK Success delete all emitters " Jog-move / continuous mode switching Additional function Continuous motion mode (Up button+ down button)×5s Run for hint×1 Release button Jog-move mode (Up button+ down button)×5s Run for hint×1 Release button During the settings, the time between two operation must be shorter than 10s, otherwise it will quit the setting. In the jog-move mode, short press the up button or down button to release within 2 seconds, and the motor will start running by jog-move. If long press is longer than 2 seconds, the motor will run continuously. Stop button×1 Run for hint ×1, Red LED always bright×1 OK Switch to jog moving mode Stop button×1 Run for hint ×2, Red LED flashes×3 OK Switch to continuous moving modeAdobe Illustrator 26.0 (Macintosh) iLovePDF