User Manual for cablematic models including: S2B5232R, Wireless Bluetooth Adapter
BLE V5.0 Beacon RS-232 Reader user manual V1.1 2019.06.10 2.2 DB9 connector: (Male) Pin Signal DTE Direction DCE Direction Description 1 N/A 2 RxD Output Input Transmitted data 3 TxD Input Output Received data 4 N/A 5 GND Ground 6 N/A 7 RTS 8 CTS 9 Vin Power Input (5~27 VDC) 2.3 Rear Side:
BLE V5.0 Beacon RS-232 Reader user manual V1.1 2019.06.10 BLE V5.0 Beacon RS-232 Reader Support "iBeaconTM", "EddystoneTM", "AltbeaconTM", Raw, TPMS, Sensors Model: S2B5232R 1. Package content: BLE Beacon RS-232 Reader Package Contents: BLE RS-232 reader x 1 A4 User manual x 1 Mini USB Cable x 1 White Box Dimension: 11 x 6 x 5 (cm) Total Package Weight: 105 g 2. Profile: 2.1 Top view: LED: Link: Blue PWR/Data: Red Radio Frequency area: Don't cover any metal material or painting. DB9 (Female) Reset to Default Mini USB (Power) + (5~40 VDC) GND LED Blue Red Description Flash when data received Solid when power on 1 BLE V5.0 Beacon RS-232 Reader user manual V1.1 2019.06.10 2.2 DB9 connector: (Male) 2: RX 3: TX 5: GND 9: Vin Pin Signal DTE Direction DCE Direction Description 1 N/A 2 RxD Output Input Transmitted data 3 TxD Input Output Received data 4 N/A 5 GND Ground 6 N/A 7 RTS 8 CTS 9 Vin Power Input (5~27 VDC) 2.3 Rear Side: DIP Switch DCE DTE DCE/DTE: Swap TX & RX 2.4 Default: All pin is "0", Baud rate 9,600 bps., 8 Data bits, None parity, 1 Stop bit. 2 BLE V5.0 Beacon RS-232 Reader user manual V1.1 2019.06.10 2.5 Baud rate option: DIP No. 8 is set to "1" (On): The baud rate is 115,200 bps, 8 Data bits, None parity, 1 Stop bit. 3. Packet Format: 3.1 Default: All DIP switch is "0". The reader will filter "UconnectTM", "iBeaconTM", "EddystoneTM" or "AltbeaconTM". $<msg type>,<reader id>,<tag type>,<tag id>,<battery>,<button>,<G-sensor>,<sensor>,<RSSI># Field Description $ start of report msg type Type of message ex. 0: reserved, 1: UconnectTM tag 2: iBeaconTM, 3: EddystoneTM, 4: AltbeaconTM reader id 6 bytes ID of reader in hex => 12 chars tag type (*) type of tag ex. 1: tag w/o g-sensor, 2: tag w/ g-sensor .. tag id 6 bytes ID of tag in hex => 12 chars tag batt (*)(**) batt voltage of tag in 1/10 volt unit tag button status (*) button status ex. 0: released, 1: pushed tag motion status (*) motion status ex. 0: non-moving, 1: moving Sensor (*)(***) Various sensor data (11 bytes) tag rssi tag read rssi # end of report Remark 1. (*): The message is "0" for iBeaconTM, EddystoneTM and AltbeaconTM beacon. 2. (**): EddystoneTM-TLM version 0 include the Tag battery information, 1/10V; The version is none "0" will display "0" in the "Tag batt" column. 3. (***): Tx Power for the iBeaconTM, altBeaconTM, EddystoneTM-UID, EddystoneTM-URL and EddystoneTM-EID beacon Example: 3 BLE V5.0 Beacon RS-232 Reader user manual V1.1 $1,00A05053849D,1,00A050172A2C,30,0,0,,-71# $2,00A05053849D,0,58E72F0CEF88,0,0,0,0,-48# $3,00A05053849D,0,772BB24ADC36,0,0,0,0,-48# $4,00A05053849D,0,012AC345EB45,0,0,0,0,-49# 2019.06.10 3.2 Raw BLE packet: The Bluetooth discovering broadcast will be filtered. All BLE beacon will be reported. DIP No. 1 is set to "1" (On) and "0" else Prefix: "$" First column: RSSI value Mac. ID: "00A05053849D" Raw packet data is between "$" and "CR" "LF" Suffix: CR LF EX: $-78,00A05053849D,0201061BFF5900AABC0100A050172A2C1E00000000000000000000000000BB $-83,00A05053849D,1EFF06000109200073C68487B4DFB227B7546E97078954811C4EB1E40DC1DF 3.3 Add the ">" at the end of Raw BLE packet: DIP No. 2 is set to "1" (On) and "0" else Prefix: "$" First column: RSSI value Raw packet data is between "$" and ">" Suffix: ">" EX: $-85,02010605166E2A850A04160F18090F09425055434B205420383030423635> 3.4 Add the ">" and "CR" "LF"at the end of Raw BLE packet: DIP No. 2 is set to "1" (On) and "0" else 4 BLE V5.0 Beacon RS-232 Reader user manual V1.1 2019.06.10 Prefix: "$" First column: RSSI value Raw packet data is between "$" and ">" Suffix: ">" "CR" "LF" 3.5 Raw iBeacon® packet only: DIP No. 1 & 2 is set to "1" (On) and "0" else Prefix: "$" First column: RSSI value Mac. ID: "00A05053849D" Raw packet data is between "$" and "CR" "LF" Suffix: "CR" "LF" EX: $-85,00A05053849D,02010605166E2A850A04160F18090F09425055434B205420383030423635 3.6 Raw EddystoneTM packet only: DIP No. 1 & 2 is set to "1" (On) and "0" else Prefix: "$" First column: RSSI value Mac. ID: "00A05053849D" Raw packet data is between "$" and "CR" "LF" Suffix: "CR" "LF" EX: $-85,00A05053849D,02010605166E2A850A04160F18090F09425055434B205420383030423635 3.7 TPMS packet: DIP No. 3 is set to "1" (On) and "0" else 5 BLE V5.0 Beacon RS-232 Reader user manual V1.1 2019.06.10 Raw data, EX: 66F35AC800 3.8 GPS Tracker & TPMS: DIP No. 1 & 3 is set to "1" (On) and "0" else, Add "AT$SNDTXT=" with TPMS packet as the section 3.6 EX: AT$SNDTXT=66F35AC800 3.9 GPS Tracker & iBeaconTM tag In/Out: DIP No. 2 & 3 is set to "1" (On) and "0" else 3.9.1 When a new iBeaconTM is detected, flag=1, major, minor, power and RSSI EX: 1;23A01AF0232A45189C0E323FB773F5EF00010002C523 1 = new beacon UUID = 23A01AF0232A45189C0E323FB773F5EF major = 0001 minor = 0002 measured power = C5 RSSI = 0x23 3.9.2 When the iBeaconTM left the device (life time ~30sec.), flag=0 6 BLE V5.0 Beacon RS-232 Reader user manual V1.1 EX: 0;23A01AF0232A45189C0E323FB773F5EF00010002 0 = lost beacon UUID = 23A01AF0232A45189C0E323FB773F5EF major = 0001 minor = 0002 2019.06.10 3.9.3 Output format: 0x02 [data from §3.8.1 & §3.8.2] 0x0D 0x0A 0x03 EX: 0x02 1;23A01AF0232A45189C0E323FB773F5EF00010002C523 CR LF 0x03 3.10 TPMS APP for ID setting: DIP No. 6 is set to "1" (On) and "0" else 3.11 TPMS APP for ID setting: DIP No. 1 & 6 is set to "1" (On) and "0" else, Add "AT$SNDTXT=" with TPMS packet as the section 3.10 3.12 Customized beacon tag: Kontakt, MineW 4. Power supply: 4.1 Voltage: 5~40 VDC, Don't exceed the limit. 4.2 There're 3 ways to power the adapter: Mini USB, Terminal Block and pin9 of DB9, please choose one. Don't power the adapter by more than one source. 4.3 The mini USB cable is inside the standard package. 7LibreOffice 7.0