User Guide for Shenzhen Longzhiyuan Technology models including: S-10T, S10T, 2AFCB-S-10T, 2AFCBS10T, LY-136 Battery WiFi Video Doorbell, LY-136, Battery WiFi Video Doorbell
Shenzhen Longzhiyuan Technology Co., Ltd. S-10T Wi-Fi Video Doorbell 2AFCB-S-10T 2AFCBS10T s 10t
File Info : application/pdf, 2 Pages, 578.07KB
DocumentDocument280x100mm User's Guide for Battery WiFi Video Doorbell Product Overview Our doorbell is a Wi-Fi enabled Smart Video Doorbell which helps you to see, hear and speak to anyone at your door from your smartphone or tablet from anywhere. This Video Doorbell supports answering ring calls from mobile App, two-way audio, instant alert, motion detection and live monitoring. Product Features Two 18650 specication batteries work regularly up to 3-6 months FHD Mega pixels collocated with wide-angle lens Support mobile phone remote fast wakeup within 4-7 seconds 2.4G Wi-Fi connection High quality two-way communication with noise cancellation Support PIR motion detection, when someone hovers at the door, it will send push alerts to your mobile phone immediately With IR-cut, it can switch automatically and it is clearly visible at both day and night to keep your home and family safe. Product Specication Sheet Lens Infrared LEDs PIR Motion Sensor Storage Connectivity Power consumption Battery Wi-Fi distance Limited distance between doorbell and chime indoor Video Compression Voice Intercom Video resolution Notications DFOV/130° Wide-angle lens (4Glass) 6pcs Infrared LEDs with 5 meters ash distance 3 meters PIR distance Up to 128GB Micro SD card 802.11b/g/n Wi-Fi@2.4G Standby 200uA Working 260 mA Two 18650 specication batteries 80 meters (open space without obstacle)15 meters (indoor) 20~30 meters H.264 Two-way audio with noise cancellation 1920*1080@15 fps Push Notications within 5-8 seconds Device Wakeup Working Temperature Storage Temperature Within 4-7s -10~ 55 -20~ 60 Install your doorbell 1 A brief introduction of the Doorbell. Camera PIR Mic Call button Speaker Reset button Charge LED USB Charge LED: Charging in Red; Full in Green. Step 1: Open the battery cover. 18650 18650 Step 2: Install 18650 battery and Mirco-SD. Mirco-SD 18650 Battery Step 3: Drill four holes in your wall, and install the anchors. Step 4: Fix the doorbell on the wall through xing screw hole. Fix screwhole Step 5: Mount doorbell in the direction of the arrow and lock it by the screws at the bottom. Indoor chime user manual Volume key Ring key Volume settings Press the "volume" button once to trigger one time. There are 4 volume levels you can choose from low to high. Change the ring Step1: Press the "ring" button to choose one you like. The indoor chime offers 38 different kinds of music for options. Each press changes the music. Step2: Press the "volume" button for 5 seconds till the music changes. Step3: Press the doorbell button to match the indoor chime. Now, the music changed. Step 6: Press the Reset button long until you hear the "system reset" prompt from the doorbell speaker. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.Corel PDF Engine Version 17.1.0.572