WIFI APPLICATION 24FT STRING LIGHTS

Package Contents

Important Notes

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Two-Year Limited Warranty

If, during normal use, this lighting fixture breaks or fails due to a defect in material and workmanship within two (2) year from the date of original purchase, simply bring this lighting fixture with your original sales receipt back to your nearest retail store. At its discretion, the retailer agrees to have the product or any defective part(s) repaired or replaced with the same or similar product free of charge, within the stated warranty period, when returned by the original purchaser with original sales receipt. This warranty: (1) excludes expendable parts including but not limited to light bulbs; (2) does not cover damage that has resulted from abuse or misuse; and (3) does not cover any losses, labor, injuries to persons/property or costs. This warranty does give you specific legal rights and you may have other rights, which vary from state to state.

Safety Information

WARNING

Please read and understand this entire manual before attempting to assemble, operate or install the product. When using outdoor use portable lighting products, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury.

Read and Follow All Safety Instructions

• Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuits or outlet to be used for the outdoor use string light product. Receptacles are available that have built-in GFCI protection for this measure of safety.
• Only use outdoor extension cords such as type SEW, SEOW, SEOOW, SOW, SOOW, STW, STOW, STOOW, SJEW, SJEOW, SJEOOW, SJW, SJOW, SJOOW, SJTW, SJTOW, or SJTOOW. This designation is marked on the wire of the extension cord.
• Read and follow all instructions that are on the product or provided with the product.
• This product operates at 12V, 1.5A, 9W per string.
• This seasonal use product is not intended for permanent installation or use.
• Do not mount or place near gas or electric heaters, fireplaces, candles, or other similar sources of heat.
• Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
• Do not let lamps rest on the supply cord or on any wire.
• Unplug the product when leaving the vicinity of the product or when left unattended.
• This is an electric product and is not a toy! To avoid risk of fire, burns, personal injury, and electric shock, it should not be played with or placed where small children can reach it.
• Do not use this product for other than its intended use.
• Do not hang ornaments or other objects from cord, wire, or light string.
• Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
• Do not cover the product with cloth, paper, or any material not part of the product when in use.
• This product is equipped with push-in type lamps.
• Do not operate this product with lamps missing from sockets. Missing lamps should be replaced promptly.
• Risk of fire: This product does not contain lamp shunts which allow the product to operate if one lamp burns out. Replace lamps only with the spare lamps provided with this product.
• DO NOT EXCEED THE MAXIMUM EXTENSION LENGTH IN FEET PERMITTED BY THE MARKING. The maximum extension length for this string light is 48 feet or 2 units.

SAVE THESE INSTRUCTIONS

California Proposition 65 Warning

This product can expose you to chemicals including Lead, which is known to the State of California to cause Cancer, birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Preparation

Before beginning assembly, installation, or operation of product, make sure all parts are present. Compare parts with package and hardware contents lists on page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts.

Tools Required for Assembly (not included)

Phillips Screwdriver, Safety Glasses, Ladder, Supporting hardware (eyebolts or brackets).

Estimated Assembly Time

20 minutes

Installation Instructions

WARNING

Disconnect power at the source prior to beginning installation or servicing product. Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit power cord or wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury or death from electric shock. String light sockets must be suspended so that lamps are facing downwards. DO NOT mount the light string with sockets facing upward. Lamps should hang freely with at least 3 inches of space from nearest object.

Step 1: Prepare Parts

Carefully remove all the parts from the packaging, and gently lay them out on a smooth workspace. Remove the packing material and uncoil the string light (A). Be careful not to cut or nick the string nor damage the pre-attached lamps.

Step 2: Secure Lamps

Ensure all 12 of the pre-attached lamps are securely affixed to each of the string light's (A) sockets by gently turning each lamp (C) clockwise. Do not over-turn.

Step 3: Connect Power Supply

Connect the 12V plug-in power supply with adapter (B) to the light string (A) by pushing the male and female end connections together, then tightening the screw-on connection cover.

Step 4: Attach String Light

Securely attach string light (A) to a support structure using the eyelet holes at the top of each suspended socket and appropriate supporting hardware (eyebolts, brackets, etc. not included).

Step 5: Plug In Power Supply

Plug-in power supply with adapter (B) to an appropriate power outlet.

Extending the Series

Step 1: Unplug Lights

Ensure that all string lights (A) are unplugged before adding additional string light (A) segments to the series.

Step 2: Remove End Cap

Remove the end cap from the last string light (A) in the series by unscrewing the plastic end cap.

Step 3: Connect Segments

Connect two string lights together by pushing the male and female end connections together, then tightening the screw-on connection cover. Ensure the new last string in the series still has its end cap attached.

Care and Maintenance

• When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on live trees in which the needles are brown and break off easily.
• If the product is placed on a tree, the tree should be well secured and stable.
• Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire insulation or cords, cracks in the lamp-holders or enclosures, loose connections, or exposed copper wire.
• When storing the product, carefully remove the product from wherever it is placed, including trees, branches, or bushes in order to avoid any undue strain or stress on the product conductors, connections, and wires. When not in use, store neatly in a cool, dry location protected from sunlight.
• Use only a mild soap and/or water with a soft cloth to clean the fixture. Harsh chemicals will damage the fixture. Do not wipe the fixture with a rough cloth that may scratch the finish or the lens.

Troubleshooting

1) The light does not come on at all:

a) Make sure the wall switch and circuit breaker are on.

2) One of the lamps has burned out:

a) Disconnect power to the string light. Remove effected lamp by gently gripping lamp and then turning in a counter-clockwise direction. Replace lamps only with 12V, 0.75W S14 lamps provided. Align the groove on the socket with the bolt on the lamp, then gently insert the lamp into the socket. Turn the lamp in a clockwise direction until fully seated.

FCC Compliance

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Radiation Exposure Statement

To maintain compliance with FCC's RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body. Use only the supplied antenna.

Quick Guide: Using Google Home to Control Smart Devices

What You Need to Get Started

Before using Google Home to control your devices, make sure you meet the following conditions:

• A Google Home device, or Android phone with Google Assistant.
• Latest Google Home App.
• Latest Google App (Android only).
• A Google account.
• The device display language must be set to English US.
• Smart Life App and a related account.
• Smart devices.

Add Devices in Smart Life App (Refer to App Instruction)

You can skip this part if you've already added some devices to your Smart Life account, and the devices' names are easily recognized.

Download Smart Life App (Refer to App Instruction)

You can scan the QR code below to download the Smart Life App. You can also search "Smart Life" in either App Store or Google Play to install the App. Note: "Smart Life" App is just a App name (for example), you can download your App.

Register a Smart Life Account and Sign In the App (Refer to App Instruction)

Open the Smart Life App, tap "Register" to register an account, then sign in the App.

Add Device and Change Device's Name (Refer to App Instruction)

Sign in with the Smart Life account, add the device, then change device name to an easily recognized word or phrase, like "bedroom light".

Set Up Google Home and Configure in Home Control

Configuration needs Google Home App. Search "Google Home" in App Store or Google Play to install the App.

Set Up Google Home with Google Home App

You can skip this part if your Google Home is already set up.

1. Make sure your Google Home is energized and four colored lights on the top are on, which means that it is in a state of waiting for a connection.
2. Make sure Google Home is in a Wi-Fi network that has smooth access to Google services.
3. Open the Google Home App; the device will automatically appear in the "Discover" page.
4. Click "SET UP" to start connecting to Google speakers and click "YES" after you hear the voice prompts.

Link Smart Life Account in Home Control

Attention: Due to the Google Home App's known bug, you could only use one Google account to control "Home Control Action". If you sign in Google Home App with several Google accounts, only the first Google account you signed in can be used for "Home Control".

1. On the homepage of Google Home App, click the button in the higher left corner, select "+", select "Set up device" under the list of "Add and manage", and then click "Have something already set up".
2. Find "Smart Life" in the list. In the new window, select your Smart Life account's region, type your Smart Life account and password, then tap "Link Now". After you assign rooms for devices, your devices will be listed in the Home Control page.

Link with Verification Code

Open Smart Life APP, click "Me > More Services > Google Assistant".

Control Your Smart Devices Through Google Home

Now you can control your smart devices through Google Home.

Step 11: Personalization Options

Click "VIEW MORE" to pop up a dialog box, and then click "I AGREE" to allow Google Home to get your calendar, flight itinerary, and more to provide personalized customization. Then set your geographic location, select the music service you need, and click on "NEXT". If you don't need it, you can click "Not Now" to skip.

Step 12: Setup Review

Then comes a review of what you have done. After clicking "Next", the page will display "Google Home is ready". At this point, Google Home's setup is complete.

Step 13: Voice Control Tutorial

This step is the voice control tutorial, click "FINISH SET UP". Then the speaker that has been connected successfully will display in the "Home" page.

Quick Guide: Using Google Home to Control Smart Devices (Alexa)

What You Need to Get Started

Before using Echo to control your smart devices, make sure you meet the following conditions:

• Stable Wi-Fi network which could access to Amazon server.
• An Echo device, including Echo, Echo Tap, or Echo Dot.
• An Amazon account.

Add Devices in Smart Life App (Refer to App Instruction)

You can skip this part if you've already added some devices to your Smart Life account, and the devices' names are easily recognized.

Download Smart Life App (Refer to App Instruction)

You can scan the QR code below to download the Smart Life App. You can also search "Smart Life" in either App Store or Google Play to install the app.

Register a Smart Life Account and Sign In the App (Refer to App Instruction)

Open the Smart Life app, tap "Register" to register an account, then sign in the app.

Add Device and Change Device's Name (Refer to App Instruction)

Sign in with the Smart Life account, add the device, then change device name to an easily recognized word or phrase.

For the first time, the distribution network should plug the power switch 3 times until the color of the lamp turns white and flashes.

1. Click Add Device
2. Click on Lighting WIFI Products
3. Enter WIFI password or click auto find device
4. Confirm the flashing status of the lamp
5. Until automatic completion
6. Find the device and click Done
7. Change the device name to an easily appropriate name
8. Get started with the lamp after finish

Link Smart Life Account to Alexa

Tap "Skills" in the hamburger menu, then search "Smart Life". Select "Smart Life" and tap "ENABLE" to enable the Skill.

You will be redirected to the account link page. Type in your Smart Life account and password, don't forget to select the country/region where your account belongs to. Then tap "Link Now" to link your Smart Life account. The country/region, the account, and the password must match with the exact content in Step 2.2.

Control Your Smart Devices Through Echo

Discover Devices

Echo needs to discover your smart devices before it controls them. You can say "Alexa, discover devices" to Echo. Echo will discover devices which have already been added in the Smart Life app. You can also tap "DISCOVER" to discover the smart devices. Discovered devices will be shown in the list.

Control Devices by Voice Commands

Now you can control your smart devices through Echo.

Note on Device Name Changes

Note: every time you change the device's name on Smart Life app, Echo must re-discover before you control them.