Installation Guide for HOOKE ROAD models including: BXG.7018-S Karoo Cargo Gladiator Rear Bumper With Dual Swing Arms and Tire Carrier, BXG.7018-S, Karoo Cargo Gladiator Rear Bumper With Dual Swing Arms and Tire Carrier, Dual Swing Arms and Tire Carrier, Arms and Tire Carrier, Tire Carrier
Hooke Road KarooCargo Gladiator Rear Bumper w/Dual Swing Arms & Tire Carrier for 2020-2024 Jeep Gladiator JT (Exclude Mojave), Offroad Bumper w/5.3-Gallon Jerry Can Holder : Automotive
Rear Bumper (1) Contents: BXG.7018-S Qty Part Name 5 Round Black Rubber Pads 2 Bearing Cover 2 Tapered Roller Bearing 2 Slotted Hex Castle Nut 3 Wheel Lug Nuts Accessories Size(mm) 36*28*25 M24 M14*15*40 8 Cable Ties 1 Gray Ratchet Straps 2 T-shaped Indexing Pin 3 Adjustable Latch U Bolt Self-lock Toggle Latch 1 Adjustable Latch U Bolt Self-lock Toggle Latch Accessory 4 Sensor Brackets 4 Rubber Stopper 2 D-rings 18*2 Picture Qty Part Name 4 Hex Bolt Bolts 8 Hex Bolt 2 Button Head Socket Cap Bolts Screws 8 Button Head Socket Cap Bolts Screws 12 Button Head Socket Cap Bolts Screws 4 Hex Socket Head Cap Screws 4 Button Head Socket Cap Bolts Screws 5 Button Head Socket Cap Bolts Screws 14 Button Head Socket Cap Bolts Screws 4 Button Head Socket Cap Bolts Screws 2 Flat Head Countersunk Bolts 12 Split Lock Washer 20 Flat Washer Size(mm) M12*35 M12*30 M10*25 M4*12 M8*20 M8*75 M6*20 M8*25 M6*16 M6*14 M6*12 D12 M12*2*30 Picture 2 Flat Washer 14 Flat Washer 8 Flat Washer 4 Flat Washer 4 Flat Washer 4 Flat Washer 4 Flat Washer 7 Flange Hex Lock Nuts 6 Flange Hex Lock Nuts 8 Hex Nuts M10*25*2 M6*12*1 M8*20*1.5 M8*25*2 M6*16*1 M8*16*1.5 M6*16*1.5 M8 M6 M12 (2) Tools required: a. Drive Socket Ratchet Wrench b. 4mm, 5mm Hex Bit Socket; c. 10mm, 13mm, 19mm, 24mm, 34mm Wrench; d. 19mm, 24mm Shallow Socket; e. 2.5mm Allen Wrench; (3) Installation time: About 2 hours, 2-3 people may be needed. Installation time may differ according to your mechanical skill level. (PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION!) To view the electronic version (BXG.7018-S), please scan the QR code. (4) Installation instruction: Step 1: Make sure all wiring is disconnected, remove your rear bumper and take out the factory wire harness. Step 2: Next, to connect the bottom connect plate and main body with M8*20 screws and M8*20*1.5 flat washers. Step 3: Lay the factory wire harness across the bumper lining up the sensor to the corresponding holes. running the wire harness though the bumper's structure. Install the sensor brackets into your bumper with the Flat Head Socket Cap Screws (M4*12). Tighten up those bolts with the 2.5mm allen wrench. At last, you can use the cable ties to fix your factory wire harness. Step 4: With assistance, lift the bumper to the vehicle and secure the bottom connect plate using M8*75 hex socket head cap screws and M8*25 flat washers. Step 5: Next, install the side mounting holes using M12*35 hex bolts. Install the bottom mounting holes using M10*25 button head socket cap bolts screws and flat washers. Make sure the wiring between the bumper and the vehicle does not get pinched. Adjust the bumper up/down as needed to level it. When the bumper is adjusted to the desired position, finish securing all of bolts. Step 6: Next, install the T-shaped Indexing Pin on both carriers. Step 7: Next, install the two tow carriers onto the already mounted rear bumper. Place the tapered roller bearing into the bearings first, then use a 34mm wrench to tighten the slotted hex castle nut into the bearings. Tighten the nuts, and finally, install the bearing cover using M6*12 flat head countersunk bolts. Step 8: The carriers have been successfully installed. Step 9: Next, install the collision prevention accessories on the carriers. Screw in the five round black rubber pads using M8*25 screws. Step 10: Next, place two of the round black rubber pads into the cushioning brackets. Step 11: Next, install one of the round black rubber pads into the driver side carrier using the M8 nuts. Step 12: Next, place one round black rubber pad and one cushioning bracket into each of the two carriers. For installing round black rubber pad, only the M8 nut is required, while for installing cushioning bracket, both the M8*16*1.5 washer and M8 nut are needed. Step 13: Next, when installing cushioning bracket, open and close the carrier to test the effect. Adjust it to the appropriate position before tightening the screws. You can also refer to the positions shown in the diagram when tightening the screws. Driver Side Passenger Side Step 14: Next, install the adjustable latch u bolt self-lock toggle latch near the D-rings on both sides of the main bumper. Use M6*16 screws with M6*12*1 washers and nuts for installation. Step 15: If you find that the length of this adjustable latch u bolt self-lock toggle latch is not sufficient, you can adjust the length by manipulating the four screws shown in the diagram. Step 16: Next, install adjustable latch u bolt self-lock toggle latch and accessory at the overlap of the two carriers. Use M6*16 screws with M6*12*1 washers and nuts for installation. Step 17: Next, above the installation position in step 14, install the hooks using M6*14 screws and M6*16*1.5 washers. Step 18: Next, install this oil drum bracket on the driver's side carrier using M8*20 screws along with M8*20*1.5 washers and nuts. Step 19: Next, demonstrate how to secure the oil drum on the oil drum bracket. This requires the use of a gray ratchet straps. You can also use the long slot for installing the oil drum without using the oil drum bracket, but please note that the oil drum is not included. Step 20: Next, install this spare tire mounting bracket on the passenger's side carrier using M12*30 hex bolts along with washers and nuts. Step 21: Install the D-rings into the bumper. Step 22: The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product! Attention: 1.The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product. 2.Please feel free to contact your distributor if you have any kind of question about your purchase.WPS 文字