HILTI Country selector
User Manual for HILTI models including: TE 5022 Hammer Drill, TE 5022, Hammer Drill, Drill
Iskanje dokumentov v tehnični knjižnici - Hilti Slovenia
Techninės bibliotekos dokumentų paieška - Hilti Lietuva
File Info : application/pdf, 88 Pages, 4.85MB
DocumentDocumentTE 5022
English
1
13
28
41
53
64
1
2 3 4 5
6 7 8
TE 5022
en
Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
ru
. . . . . . . . . . . . . . . . . . . . 13
ja
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
ko
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
zh
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
cn
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Original operating instructions
1
Information about the operating instructions
1.1 About these operating instructions
· Read these operating instructions before the product is used or operated for the first time. This is a prerequisite for safe, trouble-free handling and use of the product.
· Observe the safety instructions and warnings in these operating instructions and on the product. · Always keep the operating instructions with the product and make sure that the product is accompanied
by these operating instructions only, when the product is given to other persons.
1.2 Explanation of symbols
1.2.1 Warnings Warnings alert persons to hazards that occur when handling or using the product. The following signal words are used:
DANGER DANGER ! Draws attention to imminent danger that will lead to serious personal injury or fatality.
WARNING WARNING ! Draws attention to a potential threat of danger that can lead to serious injury or fatality.
CAUTION CAUTION ! Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the
equipment or other property.
1.2.2 Symbols in the operating instructions The following symbols are used in these operating instructions:
Comply with the operating instructions
Instructions for use and other useful information
Dealing with recyclable materials
Do not dispose of electric equipment and batteries as household waste Hilti Liion battery Hilti charger
1.2.3 Symbols in illustrations The following symbols are used in illustrations:
These numbers refer to the illustrations at the beginning of these operating instructions. The numbers in illustrations refer to important work steps or to components important for the work steps. In the text, the corresponding numbers draw attention to these work steps or components, e.g. (3). Item reference numbers are used in the overview illustration and refer to the numbers used in the key in the product overview section.
This symbol is intended to draw your special attention to certain points for handling the product.
*2373843* 2373843
English
1
1.3 Product-dependent symbols 1.3.1 General symbols Symbols used in relation to the product.
The product supports near-field communication (NFC) technology compatible with iOS and Android platforms.
Li-ion battery
Never use the battery as a striking tool. Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any other way.
1.3.2 "Must do" symbols Obligation symbols indicate "must do" actions.
Drilling without hammer action Drilling with hammering action (hammer drilling) Chiseling Chisel positioning Diameter
Rated speed under no load
Revolutions per minute
Direct current (DC)
1.4 Product information
products are designed for professional users and only trained, authorized personnel are permitted to operate, service and maintain the products. This personnel must be specifically informed about the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by untrained personnel or if used not in accordance with the intended use.
The type designation and serial number are printed on the rating plate.
Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product.
Product information
Cordless rotary hammer drill SDSMax Generation Serial no.
TE 5022 03
1.5 Declaration of conformity
The manufacturer declares, on his sole responsibility, that the product described here complies with the applicable legislation and standards. A copy of the declaration of conformity can be found at the end of this documentation. The technical documentation is filed here: Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D-86916 Kaufering, Germany
2
English
2373843 *2373843*
2
Safety
2.1 General power tool safety warnings
WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Work area safety
Keep work area clean and well lit. Cluttered or dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical safety
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
Personal safety
Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
Power tool use and care
Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
*2373843* 2373843
English
3
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
Battery tool use and care
Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130° C (265 °F) may cause explosion.
Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
Service
Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
2.2 Hammer safety warnings
Safety instructions for all operations Wear ear protectors. Exposure to noise can cause hearing loss. Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury. Hold the power tool by insulated gripping surfaces, when performing an operation where the
cutting accessory may contact hidden wiring. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.
Safety instructions when using long drill bits with rotary hammers Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher
speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury. Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.
2.3 Additional safety instructions
Use the product and accessories only when they are in perfect working order. Never tamper with or modify the product or accessories in any way. Risk of injury by falling tools and/or accessories. Before starting work, check that the battery and installed
accessories are secure. Keep the air vents clear at all times. Risk of burn injuries due to blocked air vents!
4
English
2373843 *2373843*
Apply appropriate safety measures at the opposite side of the workpiece in work that involves breaking through. Parts breaking away could fall out and / or fall down causing injury to other persons.
Always hold the tool with both hands on the grips provided. Keep the grips clean and dry. Always check that you have a safe and firm stance when you use the product. Make sure that you are
securely balanced and have control before you start the operation.
Do not touch rotating parts risk of injury! Working on the material may cause it to splinter. Flying fragments present a risk of injury to the eyes and
body. Wear eye protection, a hard hat and ear protection while the product is in use. In addition, wear light respiratory protection if you are not using a dust extractor.
Wear protective gloves when changing the accessory tool. Touching the accessory tool can result in cuts and burns.
Dust produced by grinding, sanding, cutting and drilling can contain dangerous chemicals. Some examples are: lead or lead-based paints; brick, concrete and other masonry products, natural stone and other products containing silicates; certain types of wood, such as oak, beech and chemically treated wood; asbestos or materials that contain asbestos. Determine the exposure of the operator and bystanders by means of the hazard classification of the materials to be worked. Implement the necessary measures to restrict exposure to a safe level, for example by the use of a dust collection system or by the wearing of suitable respiratory protection. The general measures for reducing exposure include:
working in an area that is well ventilated, avoidance of prolonged contact with dust, directing dust away from the face and body, wearing protective clothing and washing exposed areas of the skin with water and soap. Check that the side handle is fitted correctly and tightened securely. Check that the clamping band is engaged in the groove in the product.
Take frequent breaks and do physical exercises to improve the blood circulation in your fingers. High vibration during long periods of work can lead to disorders of the blood vessels and nervous system in the fingers, hands and wrists.
Electrical safety Before beginning work, check the working area for concealed electric cables or gas and water pipes.
External metal parts of the product could give you an electric shock or cause an explosion if you accidentally damage an electric cable or a gas or water pipe.
Power tool use and care Immediately switch off the power tool if the accessory tool jams. The product might twist off-line. Switch the product on only after you have brought it to the working position. When chiseling into ceilings, walls and floors, always make sure that you have a safe and firm stance. A
sudden break-through can affect your balance!
Apply appropriate safety measures at the opposite side of the workpiece in work that involves breaking through. Parts breaking away could fall out and / or fall down causing injury to other persons.
Wait until the product has come to a complete stop before you lay it down. Do not work off a ladder.
2.4 Careful handling and use of batteries
Comply with the following safety instructions for the safe handling and use of Li-ion batteries. Failure to comply can lead to skin irritation, severe corrosive injury, chemical burns, fire and/or explosion.
Use only batteries that are in perfect working order. Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely
harmful to health!
Do not under any circumstances modify or tamper with batteries! Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C
(176 °F).
Never use or charge a battery that has suffered an impact or been damaged in any other way. Check your batteries regularly for signs of damage.
Never use recycled or repaired batteries. Never use the battery or a battery-operated power tool as a striking tool. Never expose batteries to the direct rays of the sun, elevated temperature, sparking, or open flame. This
can lead to explosions.
Do not touch the battery poles with your fingers, tools, jewelry, or other electrically conductive objects. This can damage the battery and also cause material damage and personal injury.
*2373843* 2373843
English
5
Keep batteries away from rain, moisture and liquids. Penetrating moisture can cause short circuits, electric shock, burns, fire and explosions.
Use only chargers and power tools approved for the specific battery type. Read and follow the relevant operating instructions.
Do not use or store the battery in explosive environments. If the battery is too hot to touch, it may be defective. Put the battery in a place where it is clearly visible
and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to cool down. If it is still too hot to touch after an hour, the battery is faulty. Consult Hilti Service or read the document entitled "Instructions on safety and use for Hilti Li-ion batteries".
Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries. Read the instructions on safety and use of Hilti Li-ion batteries that you can access by scanning the QR code at the end of these operating instructions.
3
Description
3.1 Product overview 1
@ Tool holder ; Depth gauge adjustment (accessory) = Depth gauge (accessory) % Air vents & Function selector switch ( Control switch ) Grip + Battery § Battery release button / Battery status indicator : Side handle
3.2 Intended use
The product described is a cordless SDSMax rotary hammer drill with pneumatic hammering mechanism. It is designed for drilling in concrete, masonry, wood and metal. The product can also be used for light- to medium-duty chiseling on masonry and surface finishing work on concrete.
· For this product, use only Hilti Nuron lithium-ion batteries of the B 22 series. For optimum performance, Hilti recommends the batteries stated in the table at the end of these operating instructions for this product.
· For these batteries, use only Hilti chargers of the type series stated in the table at the end of these operating instructions.
3.3 Items supplied
SDSMax rotary hammer drill, side handle, grease, cleaning cloth, operating instructions. Other system products approved for use with this product can be found at your local Hilti Store or at: www.hilti.group
3.4 Active Vibration Reduction The tool is equipped with an Active Vibration Reduction (AVR) system which reduces vibration noticeably.
3.5 ATC
The product is equipped with the ATC (Active Torque Control) quick-acting electronic cut-out. If the accessory tool sticks or stalls, the product will suddenly pivot about its own axis in the opposite direction. ATC detects this sudden pivoting movement of the product and switches the product off immediately.
6
English
2373843 *2373843*
For ATC to function correctly, the product must be free to pivot. After an ATC cut-out, switch the product off and then on again.
3.6 Status indicators of the Liion battery Hilti Nuron Li-ion batteries can indicate state of charge, fault messages and the battery's state of health.
3.6.1 Indicators for state of charge and fault messages
WARNING Risk of injury by a falling battery! If the release button is pressed with a battery inserted in the product, subsequently check that the battery
is correctly re-engaged and secure.
Short-press the release button of the battery to get whichever of the following status indications is applicable at the time.
State of charge and, if applicable, faults are indicated constantly as long as the connected product is switched on.
Status Four (4) LEDs show constantly green Three (3) LEDs show constantly green Two (2) LEDs show constantly green One (1) LED shows constantly green One (1) LED slow-flashes green One (1) LED quick-flashes green
One (1) LED quick-flashes yellow
One (1) LED shows yellow One (1) LED quick-flashes red
Meaning
State of charge: 100 % to 71 %
State of charge: 70 % to 51 %
State of charge: 50 % to 26 %
State of charge: 25 % to 10 %
State of charge: < 10 %
The Li-ion battery is completely discharged. Recharge the battery. If the LED again starts quick-flashing after the battery has been charged, consult Hilti Service.
The Li-ion battery or the product in which it is inserted is overloaded, too hot or too cold, or experiencing some other fault. Bring the product and the battery to the recommended working temperature and do not overload the product when it is in use. If the message persists, consult Hilti Service.
The Li-ion battery and the product in which it is inserted are not compatible. Consult Hilti Service.
The Li-ion battery is locked and cannot be used. Consult Hilti Service.
3.6.2 Indicators showing the battery's state of health
To check the battery's state of health, press the release button and hold it down for longer than three seconds. The system does not detect a potential malfunction of the battery due to misuse, for example battery dropped or pierced, external heat damage, etc.
Status All LEDs show in sequence, followed by one (1) LED showing constantly green. All LEDs show in sequence, followed by one (1) LED quick-flashing yellow.
All LEDs show in sequence, followed by one (1) LED showing constantly red.
Meaning The battery can remain in use.
The check to ascertain the battery's state of health did not complete. Repeat the procedure, or consult Hilti Service. If a connected product can still be used, the remaining battery capacity is below 50 %. If a connected product can no longer be used, the battery has reached the end of its useful life and has to be replaced. Consult Hilti Service.
*2373843* 2373843
English
7
4
Technical data
4.1 Product information
Rated voltage Weight in accordance with EPTA-Procedure 01, without battery Single impact energy in accordance with EPTA procedure 05 Drilling diameter range in concrete/masonry (hammer drilling) Ambient temperature for operation Storage temperature
21.6 V 5.5 kg 6J 12 mm ... 32 mm -17 ... 60 -20 ... 70
4.2 Battery
Battery operating voltage Weight, battery
Ambient temperature for operation Storage temperature Battery charging starting temperature
21.6 V See the end of these operating instructions -17 ... 60 -20 ... 40 -10 ... 45
4.3 Noise information and vibration values in accordance with EN 62841
The sound pressure and vibration values given in these instructions were measured in accordance with a standardized test and can be used to compare one power tool with another. They can also be used for a preliminary assessment of exposure.
The data given represent the main applications of the power tool. However, if the power tool is used for different applications, with different accessory tools, or is poorly maintained, the data can vary. This can significantly increase exposure over the total working period.
An accurate estimation of exposure should also take into account the times when the power tool is switched off, or when it is running but not actually being used for a job. This can significantly reduce exposure over the total working period.
Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for example: maintaining the power tool and accessory tools, keeping the hands warm, organization of work patterns.
Noise information
Sound (power) level (L WA) Sound pressure level (L pA) Uncertainty (noise values) (L pA and L WA)
107 dB(A) 99 dB(A) 3 dB(A)
Total vibration Hammer drilling in concrete (ah, HD)
Chiseling (ah, ) Cheq
Uncertainty (total vibration)
B 22170 B 22255 B 22170 B 22255
8.6 m/s² 8.3 m/s² 6.8 m/s² 6.7 m/s² 1.5 m/s²
5
Preparations at the workplace
WARNING
Risk of injury by inadvertent starting! Before inserting the battery, make sure that the product is switched off. Remove the battery before making any adjustments to the power tool or before changing accessories.
Observe the safety instructions and warnings in this documentation and on the product.
8
English
2373843 *2373843*
5.1 Charging the battery 1. Before charging the battery, read the operating instructions for the charger. 2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry. 3. Use an approved charger to charge the battery. page 6
5.2 Inserting the battery
WARNING Risk of injury by short circuit or falling battery! Before inserting the battery, make sure that the contacts on the battery and the contacts on the product
are free of foreign matter. Make sure that the battery always engages correctly. 1. Charge the battery fully before using it for the first time. 2. Push the battery into the product until it engages with an audible click. 3. Check that the battery is seated securely.
5.3 Removing the battery 1. Press the battery release button. 2. Remove the battery from the product.
5.4 Fall arrest 2
WARNING Risk of injury by falling tool and/or accessory! Use only the Hilti tool tether recommended for your product. Prior to each use, always check the attachment point of the tool tether for possible damage.
Comply with the national regulations for working at heights.
As drop arrester for this product, use only the Hilti tool tether #2261971. Use the loop to secure the tool tether to the product as shown in the illustration. Check that it holds
securely. Secure the carabiner to a load-bearing structure. Check that the carabiner holds securely.
Comply with the operating instructions of the Hilti tool tether.
5.5 Fitting the side handle 3 1. Release the side handle clamping band by turning the handle grip. 2. Slide the side handle clamping band over the tool holder from the front and into the recess provided. 3. Set the side handle to the desired position. 4. Tighten the side handle clamping band by turning the handle grip.
5.6 Fitting the depth gauge (optional) 4 1. Release the side handle clamping band by turning the handle grip. 2. Release the screw at the depth gauge. 3. Slide the depth gauge from the front into the 2 guide holes provided. 4. To set the drilling depth, adjust the depth gauge to the desired drilling depth. 5. Tighten the screw at the depth gauge. 6. Tighten the side handle clamping band by turning the handle grip.
*2373843* 2373843
English
9
5.7 Fitting/removing the accessory tool 5
CAUTION Risk of injury by the accessory tool! The accessory tool might be hot or have sharp edges. Wear protective gloves when changing the accessory tool.
1. Apply a little grease to the connection end of the accessory tool. 2. Push the accessory tool into the chuck as far as it will go (until it engages).
The product is ready for use. 3. Pull the tool lock back as far as it will go and remove the accessory tool.
Use only the recommended grease supplied by Hilti. Use of unsuitable grease may cause damage to the product.
6
Operation
Observe the safety instructions and warnings in this documentation and on the product.
6.1 Drilling with hammering action (hammer drilling) 6
1. Set the function selector switch to the "Hammer drilling" position . 2. Press the drill bit against the work surface. 3. Press the control switch.
The product starts.
6.2 Chisel positioning 7
CAUTION Risk of injury! Loss of control over the chisel direction. Do not operate the tool when the selector switch is set to "Chisel positioning". Turn the function selector
switch until it engages in the "Chiseling" position.
The chisel can be adjusted to 24 different positions (in 15° increments). This ensures that flat chisels and shaped chisels can always be set to the optimum working position.
1. Set the function selector switch to the "Chisel positioning" position 2. Rotate the chisel to the desired position. 3. Turn the function selector switch until it engages in the "Chiseling"
The product is ready for use.
. position.
6.3 Chiseling 8 Set the function selector switch to the "Chiseling" position .
7
Care and maintenance
WARNING Risk of injury with battery inserted ! Always remove the battery before carrying out care and maintenance tasks!
Care of the product · Carefully remove stubborn dirt. · Carefully clean the air vents, if present, with a dry, soft brush. · Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as
these can attack the plastic parts. · Use a dry, clean cloth to clean the contacts of the product.
Care of the Liion batteries · Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush.
10 English
2373843 *2373843*
· Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of moisture (e.g. by being dipped in water or left in the rain). If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable container and consult Hilti Service.
· Keep the battery free of extraneous oil and grease. Do not permit dust or dirt to accumulate unnecessarily on the battery. Clean the battery with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents containing silicone as these can attack the plastic parts. Do not touch the contacts of the battery and do not remove the factory-applied grease from the contacts.
· Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as these can attack the plastic parts.
Maintenance
WARNING
Danger of electric shock! Improper repairs to electrical components may lead to serious injuries including burns. Repairs to the electrical section of the tool or appliance may be carried out only by trained electrical
specialists.
· Check all visible parts and controls for signs of damage at regular intervals and make sure that they all function correctly.
· Do not use the product if signs of damage are found or if parts malfunction. Immediately have the product repaired by Hilti Service.
· After cleaning and maintenance, install all guards and protective devices and check that they are in full working order.
To help ensure safe and reliable operation, use only genuine Hilti spare parts, consumables and accessories. Spare parts, consumables and accessories approved by Hilti for use with your product can be found at your Hilti Store or online at: www.hilti.group
8
Transport and storage
Transport of cordless power tools and batteries
CAUTION Accidental starting during transport ! Always transport your products with the batteries removed!
Remove the battery/batteries. Never transport batteries loose and unprotected. During transport, batteries should be protected from
excessive shock and vibration and isolated from any conductive materials or other batteries that may come in contact with the terminals and cause a short circuit. Comply with the locally applicable regulations for transporting batteries.
Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged batteries.
Prior to each use and before and after prolonged transport, check the product and the batteries for damage.
Storage of cordless power tools and batteries
WARNING Accidental damage caused by defective or leaking batteries ! Always store your products with the batteries removed!
Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in the technical data.
Do not store batteries on the charger. Always remove the battery from the charger when the charging operation has completed.
Never leave batteries in direct sunlight, on sources of heat, or behind glass. Store the product and batteries where they cannot be accessed by children or unauthorized persons. Prior to each use and before and after prolonged storage, check the product and the batteries for
damage.
*2373843* 2373843
English 11
9
Troubleshooting
If a problem occurs, always observe the status indicator of the battery. See the section headed Status indicators of the Liion battery.
If the trouble you are experiencing is not listed in this table or you are unable to rectify the problem by yourself, contact Hilti Service.
Trouble or fault No hammering action.
The battery runs down more quickly than usual.
The battery does not engage with an audible click. No response from the LEDs on the battery. The drive spindle doesn't rotate.
Product switches off automatically.
Product switches off if drill bit jams. Product or battery gets very hot.
No response from the LEDs on the battery. Product does not develop full power. Drill bit does not rotate.
The insert tool cannot be released from the chuck.
Possible cause The product is too cold.
Battery condition is not optimal.
The retaining lugs on the battery are dirty. Battery defective.
The permissible operating temperature of the product's electronics has been exceeded. The battery is not fully inserted.
The overload protection system is active.
The electronic safety shut-down has tripped to prevent further jamming. Electrical fault.
The product is overloaded (application limit exceeded). Battery defective.
The control switch is not fully pressed. The function selector switch is not engaged or is in the "Chiseling" position or the "Chisel positioning" position . Tool holder not pulled back fully.
The side handle is not fitted correctly.
Action to be taken Bring the product into contact
with the working surface, switch it on and allow it to idle. If necessary, repeat the procedure until the hammering mechanism begins to operate.
Call up the battery's state of health. Section headed "Status indicators of the Liion battery" page 7.
Clean the retaining lug and refit the battery.
Contact Hilti Service.
The ON/OFF indicator flashes. Allow the product to cool down.
Push the battery in until it engages with an audible click.
The ON/OFF indicator flashes. Release the control switch.
Allow the product to cool down. Press the control switch again. Reduce the load on the tool.
Release the drill bit.
Immediately switch off the product. Remove the battery and keep it under observation. Allow it to cool down. Contact Hilti service.
Select a product that is suitable for the intended purpose.
Contact Hilti Service.
Press the control switch as far as it will go.
With the motor at a standstill, set the function selector switch to the "Hammer drilling" position.
Pull the tool lock back as far as it will go and remove the accessory tool.
Disengage the side handle and refit it correctly so that the clamping band and side handle engage in the recess.
12 English
2373843 *2373843*
Trouble or fault Product does not start.
Possible cause
The electronic restart interlock is activated after an interruption in the electric supply.
Action to be taken
Switch the product off and then on again.
10 Disposal
WARNING Risk of injury due to incorrect disposal! Health hazards due to escaping gases or liquids. DO NOT send batteries through the mail! Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting. Dispose of your battery out of the reach of children. Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public
health and safety resources for disposal instructions.
Most of the materials from which Hilti products are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti sales representative for further information.
Do not dispose of power tools, electronic equipment or batteries as household waste!
11 Manufacturer's warranty Please contact your local Hilti representative if you have questions about the warranty conditions.
12 Further information For more information on operation, technology, environment and recycling, follow this link: qr.hilti.com/manual/?id=2373841&id=2373843 This link is also to be found at the end of the operating instructions, in the form of a QR code.
1
1.1
· (RU)
" ", 141402, , . , . , . 25, 15.26 · (BY) " ", 222750, , , -1, 18- , 2 ( . ), 1-34 · (KZ) " ", 050057, . , , . , 42/15, 012 (15) · (AM) "-", 0070, . , . 19/28
: . . : . . : www.hilti.ru
*2373843* 2373843
13
, , , . 5 . · .
. · ,
. ·
.
1.2 1.2.1 . :
! ,
.
! ,
.
! ,
( ).
1.2.2 , :
,
!
- (Li-Ion) Hilti Hilti
1.2.3 :
. (), . , (3). . .
.
14
2373843 *2373843*
1.3 1.3.1 , .
NFC, iOS Android.
-
. . , - .
1.3.2 /.
( )
(/)
1.4
,
.
.
.
.
. .
SDSMax
TE 5022
03
1.5
- , . . . () : Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering,
*2373843* 2373843
15
2
2.1
, , , . , / .
.
«» , ( ) ( ).
. .
/ , , . / , /.
/. , /.
. ! . .
, , , -/ . .
. .
, , . , , /. .
, , . , , .
, . .
, . , , . .
. , , , , , .
. , , / , . , , .
. , , .
16
2373843 *2373843*
. . .
. . , . , .
, , . .
, . .
. , . .
. , , .
, / . .
, . , . .
. , , , . . .
, . , .
, (), . . . . .
-- . .
, . .
, . .
, , , , , . .
. . . . .
. , .
*2373843* 2373843
17
. 130 °C .
, . / .
, -
. . . .
2.2
. . , .
.
. , .
.
. , , . . , () . , , , .
2.3
. / / -
. / .
, . . ! . / . . , . . , . / -- ! . . , . , . . -- .
18
2373843 *2373843*
, , , , . , : ; , , ; , , ; , . . , , . :
. . . , ,
.
, . , .
, . / .
, - -
. , () , - .
. -
.
, . , -
. !
. / .
, . .
2.4
- . , , , / .
. ,
, !
!
, , 80 °C (176 °F) .
, () - . .
.
.
, , . .
*2373843* 2373843
19
() , , . , .
, . , , , .
. , .
. (, )
. . . , , , . Hilti « - Hilti».
, .
- Hilti, QR- .
3
3.1 1
@ ; (-
)
= () % & ( ) + § / :
3.2
SDSMax . , , . , . · - Hilti
B 22 Nuron. Hilti , . · Hilti, .
3.3
SDSMax, , , , .
20
2373843 *2373843*
, , Hilti Store www.hilti.group
3.4 Active Vibration Reduction Active Vibration Reduction (AVR), .
3.5 ATC ATC (Active Torque Control). . ATC .
. , .
3.6 -
- Hilti Nuron , .
3.6.1
!
.
.
, , ( ) .
(4) . (3) . (2) . (1) . (1) . (1) .
(1) .
: 100 % 71 %
: 70 % 51 % : 50 % 26 % : 25 % 10 % : < 10 %
- . . , Hilti. - , , . . , Hilti.
*2373843* 2373843
21
(1) .
(1) .
- . Hilti.
- . Hilti.
3.6.2
3 . , , , , . .
, (1) .
, (1) .
, (1) .
.
. Hilti. 50 %. , . Hilti.
4
4.1
EPTA-Procedure 01 EPTA 05 / ( )
4.2
21,6 5,5 6 12 ... 32
-17 ... 60 -20 ... 70
21,6 . -17 ... 60 -20 ... 40 -10 ... 45
4.3 EN 62841
. .
. , , () , .
22
2373843 *2373843*
.
, . .
/ , : () , , .
(L WA) (L pA) ( ) (L pA L WA)
107 () 99 () 3 ()
(ah, HD)
(ah, ) Cheq
( )
B 22170 B 22255 B 22170 B 22255
8,6 /² 8,3 /² 6,8 /² 6,7 /² 1,5 /²
5
!
, .
.
, .
5.1
1. . 2. , . 3. . 20
5.2
! . , .
1. . 2. ,
. 3. .
5.3
1. . 2. .
*2373843* 2373843
23
5.4 2
/ ! Hilti
. -
.
.
Hilti #2261971. ,
. . - . -
.
Hilti.
5.5 3
1. , ( ) . 2. ( )
. 3. . 4. , ( ) .
5.6 () 4
1. , ( ) . 2. . 3. -
. 4. . 5. . 6. , ( ) .
5.7 / 5
! . .
1. . 2. .
. 3. .
Hilti. .
6
, .
24
2373843 *2373843*
6.1 ( ) 6
1. « » . 2. . 3. .
.
6.2 7
! . ,
« ». «» ( ).
24 ( 15°). .
1. « » . 2. . 3. «» ( ).
.
6.3 8 «» .
7
! !
· . · ( ) . · .
, . · .
- · .
. · .
(, ). , , . Hilti. · , . . . , . , . · . , .
*2373843* 2373843
25
! . -.
· , -- .
· / . Hilti.
· .
, . Hilti , Hilti Store : www.hilti.group
8
! !
(). ( ).
, , , . .
. - , .
, .
! !
. , .
. .
, / .
. ,
.
9
. . - .
, , Hilti.
26
2373843 *2373843*
.
, .
. . .
.
. .
. . .
.
.
.
.
. . .
, .
( ).
.
. , .
. . « - » 21.
.
Hilti.
«./.» . .
.
«./.» . .
. . .
/.
. . . Hilti.
.
Hilti.
.
«»
« » .
« » .
() .
.
.
. .
*2373843* 2373843
27
.
.
, .
10
! . ! ,
. , . Hilti Store
.
, Hilti, . ( ). Hilti (, ) . Hilti.
, / !
11 Hilti.
12 , , . : qr.hilti.com/manual/?id=2373841&id=2373843 QR-.
1
1.1
·
· ·
1.2 1.2.1
28
2373843 *2373843*
1.2.2
Hilti Li-Ion Hilti
1.2.3
3
1.3 1.3.1
iOS Android NFC
Li-Ionen
1.3.2
*2373843* 2373843
29
1.4
SDSMax
TE 5022
03
1.5
Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE
2
2.1
30
2373843 *2373843*
*2373843* 2373843
31
130 °C265 °F
2.2
2.3
-
32
2373843 *2373843*
2.4
Li-Ion
80°C176°F
1 Hilti Hilti Li-Ion
Li-Ion QR Hilti Li-Ion
*2373843* 2373843
33
3
3.1 1
@ ; = % & ( ) + § / :
3.2 SDSMax · Hilti Nuron B 22 Li-Ion
Hilti · Hilti
3.3 SDSMax Hilti Store www.hilti.group
3.4 Active Vibration Reduction Active Vibration Reduction (AVR)
3.5 ATC ATCActive Torque Control ATC
3.6 Li-Ion
Hilti Nuron Li-Ion
3.6.1
34
2373843 *2373843*
4 LED4 3 LED3 2 LED2 1 LED1 1 LED1 1 LED1
1 LED1
1 LED1
1 LED1
100 %...71 %
70 %...51 %
50 %...26 %
25 %...10 %
< 10 %
Li-Ion LED Hilti
Li-Ion Hilti
Li-Ion Hilti
Li-Ion Hilti
3.6.2
3
LED 1 LED1 LED 1 LED1
LED 1 LED1
Hilti
50% Hilti
4
4.1
EPTA-Procedure 01 1 EPTA 05
21.6 V 5.5 kg 6J 12 mm ... 32 mm -17 ... 60 -20 ... 70
*2373843* 2373843
35
4.2
21.6 V -17 ... 60 -20 ... 40 -10 ... 45
4.3 EN 62841
(L WA) (L pA) (L pA L WA)
107 dB(A) 99 dB(A) 3 dB(A)
(ah, HD)
(ah, ) Cheq
B 22170 B 22255 B 22170 B 22255
8.6 m/s² 8.3 m/s² 6.8 m/s² 6.7 m/s² 1.5 m/s²
5
5.1
1. 2. 3. 34
5.2
36
2373843 *2373843*
1. 2. 3.
5.3 1. 2.
5.4 2
Hilti
Hilti #2261971
Hilti
5.5 3 1. 2. 3. 4.
5.6 4 1. 2. 3. 2 4. 5. 6.
5.7 5
1. 2.
3.
Hilti
*2373843* 2373843
37
6
6.1 6
1. 2. 3.
6.2 7
24 15°
1. 2. 3.
6.3 8
7
· · ·
·
Li-Ion ·
·
Hilti · ·
38
2373843 *2373843*
·
· Hilti
·
Hilti Hilti Store www.hilti.group
8
9
Li-Ion
Hilti
*2373843* 2373843
39
Li-Ion
34
LED
Hilti
ON/OFF
ON/OFF
Hilti
LED
Hilti
10
Hilti Store
40
2373843 *2373843*
Hilti Hilti Hilti
11 Hilti
12 qr.hilti.com/manual/?id=2373841&id=2373843 QR
1
1.1
· . .
· . ·
.
1.2 1.2.1 . .
! .
.
! .
.
! . .
1.2.2 .
*2373843* 2373843
41
Hilti Hilti
1.2.3 .
. . (: (3)). . , .
1.3 1.3.1 .
iOS Android NFC .
. . .
1.3.2 .
()
1.4 , ,
. . . .
42
2373843 *2373843*
. .
SDSMax
TE 5022
03
1.5
. . . Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE
2
2.1
, , , /
" " ( ) ( )
,
,
, , ,
, , ,
,
,
,
, , ,
/ , OFF
,
,
*2373843* 2373843
43
, ,
,
,
,
, /
, ,
, , ,
,
,
, , , ,
, , , ,
,
130 °C (265 °F)
2.2
. . . . ,
. .
44
2373843 *2373843*
.
. .
.
2.3
. . / .
. . ! , .
. . . , .
. . - ! . .
, , . , . . . , , . , , , , , , . . . : , , , . . . , . , .
, ,
. , , .
. . . , .
! , .
. . .
2.4
. , , , / .
. , ! !
*2373843* 2373843
45
80 °C (176 °F) . .
.
. . , , .
.
, , . , .
. , , , .
. .
. .
. . . Hilti " Hilti " .
, .
Hilti QR .
3
3.1 1
@ ; - () = () % & ( ) + § / :
3.2
SDSMax. , , . , . · B 22 Hilti Nuron . Hilti
. · Hilti .
3.3
SDSMax, , , , . Hilti Store . www.hilti.group
46
2373843 *2373843*
3.4 Active Vibration Reduction Active Vibration Reduction (AVR) .
3.5 ATC ATC (Active Torque Control) . , . ATC .
. .
3.6 Hilti Nuron , .
3.6.1
! ,
.
, . .
4 LED 3 LED 2 LED 1 LED 1 LED 1 LED
1 LED
1 LED 1 LED
: 100 % ~ 71 %
: 70 % ~ 51 %
: 50 % ~ 26 %
: 25 % ~ 10 %
: < 10 %
. . LED , Hilti .
, . , . , Hilti .
. Hilti .
. Hilti .
3.6.2
, 3 . , , .
LED 1 LED .
LED 1 LED .
.
. Hilti .
*2373843* 2373843
47
LED 1 LED .
, 50% . , . Hilti .
4
4.1
EPTA-Procedure 01 ( ) EPTA-Procedure 05 1 / ( )
21.6V 5.5kg 6J 12mm ... 32mm -17 ... 60 -20 ... 70
4.2
21.6V -17 ... 60 -20 ... 40 -10 ... 45
4.3 EN 62841
, . .
. . .
. .
/ . , , .
(L WA) (L pA) () (L pA L WA)
107dB(A) 99dB(A) 3dB(A)
(ah, HD)
(ah, ) Cheq
( )
B 22170 B 22255 B 22170 B 22255
8.6m/s² 8.3m/s² 6.8m/s² 6.7m/s² 1.5m/s²
48
2373843 *2373843*
5
! . .
.
5.1
1. . 2. . 3. . 46
5.2
! . .
1. , . 2. . 3. .
5.3
1. . 2. .
5.4 2
/ ! Hilti . .
.
Hilti #2261971 . .
. .
.
Hilti .
5.5 3
1. ( ) . 2. ( ) . 3. . 4. ( ) .
*2373843* 2373843
49
5.6 () 4 1. ( ) . 2. . 3. 2 . 4. . 5. . 6. ( ) .
5.7 / 5
! . .
1. 2. .
. 3. .
Hilti . .
6
.
6.1 () 6
1. "" . 2. . 3. .
.
6.2 7
! " " .
"" .
24 (15°) . .
1. " " . 2. . 3. ""
.
.
6.3 8 ""
.
7
! !
50
2373843 *2373843*
· . · , . · .
. · .
· .
. · .
(: ). , . , Hilti . · . . . . , . · . .
! . .
· .
· . Hilti .
· .
, . Hilti , Hilti Store www.hilti.group
8
! !
. .
. .
. .
.
! !
. . . . , . . .
*2373843* 2373843
51
9
. .
Hilti .
.
. " " . LED . .
.
.
.
LED . . .
.
.
.
.
. . . . .
. .
( ). . . "" " " . . .
.
. .
. " " 47.
.
Hilti .
ON/OFF . .
.
ON/OFF .
. . . .
.
. . . Hilti .
.
Hilti .
.
" " .
.
, .
.
52
2373843 *2373843*
10
! . ! . . Hilti Store .
Hilti . . Hilti . Hilti .
, !
11 Hilti .
12 , , : qr.hilti.com/manual/?id=2373841&id=2373843 QR .
1
1.1
· · ·
: : 162422041 : 0800-221-036
1.2 1.2.1
!
!
*2373843* 2373843
53
1.2.2
Hilti Hilti
1.2.3
(3)
1.3 1.3.1
NFCiOSAndroid
1.3.2
54
2373843 *2373843*
DC
1.4
HiltiHilti
SDSMax
TE 5022
03
1.5
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D-86916 Kaufering, Germany
2
2.1
/
RCD
RCD
*2373843* 2373843
55
/
130° C265 °F
2.2
2.3
56
2373843 *2373843*
/
/
2.4
/
80°C176°F
Hilti Hilti
Hilti
*2373843* 2373843
57
3
3.1 1
@ ; = % & ( ) + § / :
3.2 SDSMax · B 22Hilti NuronHilti
· Hilti
3.3 SDSMax Hilti Storewww.hilti.group
3.4 Active Vibration Reduction Active Vibration Reduction (AVR)
3.5 ATC ATCActive Torque Control ATC
ATC ATC
3.6 Hilti Nuron
3.6.1
58
2373843 *2373843*
4LED 3LED 2LED 1LED 1LED 1LED
1LED
1LED 1LED
100 %71 %
70 %51 %
50 %26 %
25 %10 %
< 10 %
LEDHilti
Hilti
Hilti
Hilti
3.6.2
3
LEDLED
LEDLED
LEDLED
Hilti 50% Hilti
4
4.1
EPTA-Procedure 01 EPTA05 /
21.6 V 5.5 kg 6J 12 mm ... 32 mm -17 ... 60 -20 ... 70
4.2
21.6 V -17 ... 60 -20 ... 40 -10 ... 45
*2373843* 2373843
59
4.3 EN 62841
/
(L WA) (L pA) (L pAL WA)
107 dB(A) 99 dB(A) 3 dB(A)
(ah, HD)
(ahCheq)
B 22170 B 22255 B 22170 B 22255
8.6 m/s² 8.3 m/s² 6.8 m/s² 6.7 m/s² 1.5 m/s²
5
5.1
1. 2. 3. 58
5.2
1. 2. 3.
5.3
1. 2.
60
2373843 *2373843*
5.4 2
/ Hilti
Hilti#2261971
Hilti
5.5 3 1. 2. 3. 4.
5.6 4 1. 2. 3. 4. 5. 6.
5.7 / 5
1. 2.
3.
Hilti
6
6.1 6
1. 2. 3.
*2373843* 2373843
61
6.2 7
2415°
1. 2. 3.
6.3 8
7
!
· · · ·
· ·
Hilti ·
·
· · Hilti ·
HiltiHilti Store Hiltiwww.hilti.group
8
!
62
2373843 *2373843*
9
Hilti
LED
LED
58
Hilti ON/OFF
ON/OFF
Hilti
Hilti
*2373843* 2373843
63
10
Hilti Store
HiltiHilti Hilti
11 Hilti Hilti Taiwan Co., Ltd. 24F., No. 16, Xinzhan Rd., Banqiao Dist., New Taipei City 220, Taiwan (R.O.C.) Tel. 0800221036
12 qr.hilti.com/manual/?id=2373841&id=2373843 QR
1
1.1
· · ·
1.2 1.2.1
-
-
-
64
2373843 *2373843*
1.2.2
Hilti Hilti
1.2.3
(3)
1.3 1.3.1
(NFC) iOS
1.3.2
() (DC)
*2373843* 2373843
65
1.4
Hilti Hilti
SDSMax
TE 5022 03
1.5
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D-86916 Kaufering, Germany
2
2.1
/ "" () ()
() ()
(RCD) RCD
/"" ""
66
2373843 *2373843*
/ ( )
() /
130 °C (265 °F)
()
2.2
2.3
/
*2373843* 2373843
67
2.4
/
80 (176 )
Hilti " Hilti "
Hilti
68
2373843 *2373843*
3
3.1 1
@ ; - () = () % & ( ) + § / :
3.2 SDSMax · Hilti Nuron B 22 Hilti
· Hilti
3.3 SDSMax Hilti Store www.hilti.group
3.4 Active Vibration Reduction Active Vibration Reduction (AVR)
3.5 ATC ATC(Active Torque Control) ATC
ATC ATC
3.6 Hilti Nuron
3.6.1 --
*2373843* 2373843
69
(4) LED (3) LED (2) LED (1) LED (1) LED (1) LED
(1) LED
(1) LED (1) LED
100 % 71 %
70 % 51 %
50 % 26 %
25 % 10 %
< 10%
LED Hilti
Hilti
Hilti
Hilti
3.6.2
LED (1) LED
LED (1) LED
LED (1) LED
Hilti 50% Hilti
4
4.1
EPTA-Procedure 01 () ( EPTA 05) / ()
21.6 V 5.5 kg 6J 12 mm ... 32 mm -17 ... 60 -20 ... 70
4.2
21.6 V -17 ... 60 -20 ... 40 -10 ... 45
70
2373843 *2373843*
4.3 EN 62841
/
() (L WA) (L pA) () (L pA L WA)
107 dB(A) 99 dB(A) 3 dB(A)
(ahHD)
(ahCHeq)
()
B 22170 B 22255 B 22170 B 22255
8.6 m/s² 8.3 m/s² 6.8 m/s² 6.7 m/s² 1.5 m/s²
5
--
5.1
1. 2. 3. 69
5.2
-
1. 2. 3.
5.3
1. 2.
*2373843* 2373843
71
5.4 2
- Hilti
Hilti #2261971
Hilti
5.5 3 1. () 2. () 3. 4. ()
5.6 () 4 1. () 2. 3. 4. 5. 6. ()
5.7 / 5
-
1. 2. ()
3.
Hilti
6
6.1 () 6
1. "" 2. 3.
72
2373843 *2373843*
6.2 7
- """"
24 ( 15° )
1. "" 2. 3. ""
6.3 8 ""
7
- !
· · () · ·
· · (
) Hilti · ·
-
· · Hilti ·
Hilti Hilti Hilti Store www.hilti.group
*2373843* 2373843
73
8
-
()
- !
9
Hilti
( ) LED
LED
() " " ""
" " 69
Hilti "/" "
"
"/"
Hilti
Hilti
""
74
2373843 *2373843*
10
- () Hilti Store
Hilti Hilti Hilti
11 Hilti
12 qr.hilti.com/manual/?id=2373841&id=2373843
*2373843* 2373843
75
76
2373843 *2373843*
*2373843*
2373843
Hilti = registered trademark of Hilti Corp., Schaan
Pos. 8 | 20230704