DigiTech Bass Synth Wah Bass Envelope Filter
The Power to Create
Product Overview
The Bass Synth Wah is an exciting combination of seven different synth and wah effects, including envelope filter, synth tones, filter generators, and octave shift. It can be run inline with your current pedals or parallel with your bass tone to create unique combinations of both bass and synth sounds.
Controls
1. Sens Knob: Controls the trigger sensitivity of the envelope, synth, and filter effects. Turn this knob clockwise to increase sensitivity and counter-clockwise to decrease it.
2. Control Knob: Controls different functions depending on the selected Bass Synth Wah Type. Refer to the Effects Matrix for detailed descriptions.
3. AC Adapter Jack: Connect a DigiTech PS200R (9VDC) power supply to this jack. Use the proper supply for your area's mains line voltage.
4. Range Knob: Controls different functions depending on the selected Bass Synth Wah Type. Refer to the Effects Matrix for detailed descriptions.
5. Type Knob: Selects one of seven different envelope, synth, or filter types:
- 1-ENV FILTER: Classic envelope filter sound.
- 2-SUB ENV: Envelope filter effect with an octave down pitch shift blended in.
- 3-SYNTH 1: Monophonic synth tone generator with an opening filter envelope.
- 4-SYNTH 2: Monophonic synth tone generator with a closing filter envelope.
- 5-FILTER 1: DigiTech's famous Synth Talk™ effect.
- 6-FILTER 2: Synth Talk™ effect with inverse filter envelope.
- 7-OCTASUB: An octave down pitch shift effect with a variable synth effect mix using the RANGE knob.
6. Input Jack: Connect your instrument to this jack. Connecting a 1/4" cable to this jack supplies battery power even though the Indicator LED may not be lit. To prolong battery life, disconnect cables when not in use.
7. Pedal Release Pins: These are spring-loaded hinges that hold the pedal in place. Push these pins in to release the pedal from the chassis, exposing the battery compartment.
8. Pedal: Press the pedal to turn the effect on and off.
9. Out 1 Normal (Dry) Jack: Use this output when only one amplifier or mixer channel is used. When both Out 1 Normal (Dry) and Out 2 (Effect) are connected, only the dry, unprocessed bass signal is present at Out 1 Normal (Dry) when the Bass Synth Wah is on or bypassed.
10. Indicator LED: This LED indicates when the effect is turned on. If the LED becomes dim or does not light when cables are connected, the battery needs to be replaced.
11. Out 2 (Effect) Jack: Connect this output to a second amplifier or mixer channel for effect signal only. When Out 2 is connected, only effect signal is present when the Bass Synth Wah is turned on. Out 2 is muted when the Bass Synth Wah is bypassed.
Effects Matrix
| Type | SENS | CONTROL | RANGE |
|---|---|---|---|
| 1- Env Filter | Trigger Sensitivity | Wet/Dry Mix | Range |
| 2- Sub Env | Trigger Sensitivity | Wet/Dry Mix | Range |
| 3- Synth 1 | Trigger Sensitivity | Synth Attack | Cutoff Freq |
| 4- Synth 2 | Trigger Sensitivity | Synth Attack | Cutoff Freq |
| 5- Filter 1 | Trigger Sensitivity | Filter Attack | Freq Envelope |
| 6- Filter 2 | Trigger Sensitivity | Filter Attack | Freq Envelope |
| 7- OctaSub | Trigger Sensitivity | Sub Level | Synth Level |
Connections
The Bass Synth Wah has a single input and a pair of outputs. For optimal triggering of effects, it should be the first effect pedal in your chain.
Single Amplifier Setup: Use the 'Out 1 Normal (Dry)' jack when connecting to a single amplifier or mixer input. The effected signal is present when the pedal is on, and a dry unprocessed signal is present when bypassed.
Dual Setup (Amp & Mixer): Connect 'Out 1 Normal (Dry)' to your bass amp and 'Out 2 (Effect)' to a mixer channel. This configuration allows 'Out 1 Normal (Dry)' to send a dry, unprocessed bass signal to your amplifier, while 'Out 2 (Effect)' sends only the effect signal to the mixer. This setup enables separate control over your amp and synth effect signals for dramatic bass/synth applications.
Diagram Description: The connection diagram illustrates a setup where a guitar is connected via the Bass Synth Wah's input. The Bass Synth Wah's 'Out 1 (AMP)' is connected to an amplifier, and its 'Out 2 (MIXER)' is connected to a mixer. Another pedal, the DigiTech Bass Driver, is shown connected in series before the Bass Synth Wah. An optional PS200R power supply is indicated.
CIT™ Cabinet Modeling
The Bass Synth Wah features built-in CIT™ cabinet modeling. When enabled, CIT cabinet modeling simulates a 4x10 bass speaker cabinet, providing a "through-an-amp" sound when running direct to a mixer or recording device.
To Enable CIT™ Cabinet Modeling:
- Press and hold the Pedal down.
- Apply power by connecting a 1/4" instrument cable to the Bass Synth Wah Input or connect the PS200R power supply to the AC Adapter Jack.
CIT cabinet modeling must be turned on each time power is applied to the Bass Synth Wah.
Sample Settings
1. Funky Envelope: (Visual representation of knob settings)
2. Slow Synth: (Visual representation of knob settings)
3. Synth Bass: (Visual representation of knob settings)
4. Synth Ya: (Visual representation of knob settings)
5. Octa Sub Synth: (Visual representation of knob settings)
Battery Replacement
Instructions:
- Using the tip of a 1/4" cable, push one of the release pins on either side of the pedal and remove the pedal from the chassis.
- Remove the battery from the battery compartment and disconnect the battery cable.
- Connect a new battery to the battery cable and place it back in the compartment. Ensure the battery cable does not interfere with the spring or pedal switch arm.
- Place one hole of the pedal over its corresponding pin.
- Push the opposite pin in and lower the other side of the pedal into place over the depressed pin. Release the pin. When properly fastened, both release pins will be flush with the outer side of the pedal.
Diagram Description: The diagram shows the components involved in battery replacement: the Pedal, Pedal Switch Arm, Pedal Release Pins, Battery Compartment, Spring, 9V DC Battery, and Pedal Chassis.
Specifications
- Controls: Sens, Control, Range, Type, On/Off Pedal
- Jacks: Input, Out 1 Normal (Dry), Out 2 (Effect)
- Input Impedance: 1 MOhms
- Output Impedance: 100 Ohms
- Power Supply: 9V Alkaline Dry Battery
- Power Consumption: 4.8 Watts (with optional PS200R power supply)
- Battery Life: Approximately 4 hours (with continuous usage)
- Dimensions: 4 15/16"(L) x 3 1/8"(W) x 2 1/8"(H)
- Weight: 1.38 lbs.
- Optional Power Supply: PS200R - 100 (100V ~ 50/60Hz), PS200R - 120 (120V ~ 60Hz), PS200R - 230 (230V ~ 50Hz), PS200R - 240 (240V ~ 50Hz)
Declaration of Conformity & Warning
Manufacturer: DigiTech
Address: 8760 S. Sandy Parkway, Sandy, Utah 84070, USA
Product: Bass Synth Wah
Product Option: Requires Class II power adapter conforming to EN60065, EN60742, or equivalent.
Product Specifications Conformance: Safety: IEC 60065 (1998), EMC: EN 55013 (1990), EN 55020 (1991)
Supplementary Information: Complies with Low Voltage Directive 72/23/EEC and EMC Directive 89/336/EEC as amended by Directive 93/68/EEC.
European Contact: Harman Music Group, 8760 South Sandy Parkway, Sandy, Utah 84070 USA. Ph: (801) 566-8800, Fax: (801) 568-7583
Important Safety Instructions:
- Read and keep these instructions.
- Heed all warnings.
- Do not use near water.
- Clean only with a dry cloth.
- Do not block ventilation openings; install per manufacturer's instructions.
- Do not install near heat sources.
- Protect the power cord from being walked on or pinched.
- Unplug during lightning storms or when unused for long periods.
- No user-serviceable parts inside; refer servicing to qualified personnel.
- Servicing is required for damage (e.g., power cord, liquid spills, dropped apparatus, exposure to rain/moisture, abnormal operation).
- WARNING: To reduce fire or electric shock risk, do not expose to rain or moisture.
- Refer to unit labels for pertinent information.
Warranty
DigiTech products come with a comprehensive warranty:
- Warranty registration card must be mailed within ten days of purchase to validate the warranty.
- DigiTech warrants the product, when used solely within the U.S., to be free from defects in materials and workmanship under normal use and service.
- DigiTech's liability is limited to repairing or replacing defective materials. Products must be returned to DigiTech WITH RETURN AUTHORIZATION. Parts and labor are covered for one year, extended to six years if properly registered. A Return Authorization number can be obtained by telephone. DigiTech is not liable for consequential damage.
- Proof-of-purchase is the consumer's responsibility.
- DigiTech reserves the right to make design changes or improvements without obligation to install them on previously manufactured products.
- The warranty is forfeited if the product's main assembly is opened or tampered with by unauthorized personnel, or if used with AC voltages outside the suggested range.
- This warranty is in lieu of all other warranties. DigiTech does not assume or authorize any person to assume any obligation or liability in connection with the sale of this product. DigiTech or its dealers are not liable for special or consequential damages or delays beyond their control.
Note: Information in this manual is subject to change without notification and may contain inaccuracies due to undocumented product changes. This version supersedes all previous versions.
Contact Information
DigiTech
8760 South Sandy Parkway
Sandy, Utah 84070
PH: (801) 566-8800
FAX: (801) 568-7583
Visit DigiTech on the World Wide Web at: www.digitech.com
DigiTech and X-Series are trademarks of Harman Music Group, Inc.
Copyright - Harman Music Group
Printed 8/2002
Manufactured in the USA
Model Number: 18-1813-A
