User Guide for BROAN models including: FIN-180B FRESH IN Basic Supply Fan, FIN-180B, FRESH IN, Basic Supply Fan, Supply Fan
Broan FRESH-IN 180 CFM Basic Supply Fan | Sylvane
Broan FIN-180B Fresh In⢠180 CFM Full Install Energy Star | Build.com
BROANTM Fresh In Basic FIN-180B; see table for available part numbers. 30-180 CFM at 0.2 in. w.g. 30-170 CFM at 0.4 in. w.g. The Broan Fresh In series is a quiet and effective supply air solution for hot and mixed climates, offering renewed fresh air comfort. It offers the greatest reduction of HERS score compared to CIFS solutions. Thanks to their ECM motors, the Basic FIN-180B and FIN-180B-HW models deliver energyefficient continuous ventilation at a constant airflow in typical installations. Designed to be the most versatile, reliable and energy-efficient supply fan on the market, it can also be installed horizontally, vertically, upside down, or flush to the ceiling. Two models are available: with a power cord or hardwired. Mechanical components · High efficiency ECM motor · Constant airflow blower designed to maintain the selected airflow in standard installations · Silent ventilation with balanced metallic dual inlet blower wheel · Spring loaded damper · Blower efficiency as high as 12.4 CFM/W · Protection grille for blower Electronic features · Adjustable speed from 30 to 180 CFM in 10 CFM increments Installation features · Five installation possibilities: ceiling hung, flush to ceiling, attic mounted, ceiling mounted and wall mounted · Paintable door and frame · Compact and designed to fit between 12-in. cc joists · 6-in. diameter ports with integrated test ports and bumps to maintain tie-trap in place · 6-ft. power cord (FIN-180B) or hardwired (FIN-180B-HW) · Easy maintenance: can be done within 5 minutes through the access door FIN-180B 6-ft. power cord VB0260 Options FIN-180B-HW Hardwired Description Part no. 9.25" x 9.25" x 2" MERV 8 filter FIN- MERV8 9.25" x 9.25" x 2" MERV 13 filter FIN-MERV13 Paintable decorative finishing trim for discreet FIN-R1015 installation Installation bracket, including hardware, for FIN-S1624 installation between joists of 16-in. cc and 24-in. cc Warranty The BROANTM Fresh In Basic is protected by a 5-year warranty on parts only. Requirements and standards When properly installed and set, this unit will meet requirements of: · EPA Indoor airPLUS, Version 1 · 2012 & 2015 IECC, Version 2018 · 2012 & 2015 IRC, Version 2018 · ENERGY STAR Certified Homes, Version 3 · ASHRAE 62.2-2010 & 62.2-2016 · Characteristics Power Weight Shipping weight Ports diameter Width Length Height Min. operating temperature FIN-180B FIN-180B-HW 6-ft. power cord Hardwired 11 lb. 14.5 lb. 6 in. 10 ¼ in. 14 ¾ in. (without ports) 10 in. 14 °F Mounting options Can be installed as a stand alone unit or connected to the return ducting of an AHU. Ceiling Hung Attic Mounted Under Ceiling 12" 10" Flush to Ceiling 12" VH0153A VD0466 14¼" clearance 10¼" VH0154 VD0467 With optional decorative trim Wall Mounted 10" 10" Electricity Consumption MERV 13 Main Filter Airflow setting (CFM) Static Pressure (in. w. g.) Power (Watts) Efficiency (CFM/Watts) Power (Watts) Efficiency (CFM/Watts) Factory Setting: 80 CFM 120 VAC, 60 Hz, 0.7 Amp Installation Zones 30 0.1 0.2 4.8 6.8 6.3 4.4 5.2 7.2 5.8 4.2 VH0152 60 0.1 0.2 7.0 8.9 90 120 180 0.1 0.2 0.4 0.1 0.2 0.4 0.1 0.2 0.4 7.8 10.8 19.0 9.7 14.4 22.5 22.0 27.0 37.7 8.6 6.7 11.5 8.3 4.7 12.4 8.3 5.3 8.2 6.7 5.3 7.4 10.8 11.3 15.2 22.7 17.0 21.2 N/A 32.5 37.0 N/A 8.1 5.6 8.0 5.9 4.0 7.1 5.7 N/A 5.5 4.9 N/A VN0011A Installation allowed in zones 1-4. Refer to the installation instructions for more details. Fan Curve Examples Airflow adjustable from 30 to 180 CFM in 10 CFM increments. Fan curve examples with main filter 0.7 Fan curve examples with MERV 8 filter 0.6 Pressure (in w.g.) Pressure (in w.g.) 0.6 0.5 0.5 0.4 0.4 0.3 0.3 0.2 0.2 0.1 0.1 0 0 20 40 60 80 100 120 140 160 180 200 Airflow (CFM) 0 0 20 40 60 80 100 120 140 160 180 200 Airflow (CFM) Insulated door Damper assembly 14¼" Unit setting Pressure (in w.g.) Pressure (in w.g.) Fan curve examples with MERV 13 filter 0.6 0.5 0.4 0.3 0.2 0.1 0 0 20 40 60 80 100 120 140 160 180 200 Airflow (CFM) Fan curve examples with MERV 16 filter 0.6 0.5 0.4 0.3 0.2 0.1 0 0 20 40 60 80 100 120 140 160 180 200 Airflow (CFM) MERV 16 filters are not available through Broan. Performance may vary according to brand. Blower motor Blower wheel Insulated housing Product specifications are subject to change without notice. Test port Test port Electronic board Filter A&E Specs Performance Requirements · Unit's blower shall be designed to maintain a constant airflow in typical installations · Unit speed shall be selectable from 30 to 180 CFM in 10 CFM increments. · Backdraft damper shall have a magnet to prevent flickering and stay closed during door blower test. · Unit's blower efficiency shall be at least 8.3 CFM/W at 120 CFM, 0.2 in. w.g. · Unit shall be equipped with test ports to allow airflow measurement. · Unit shall have an access door that allows quick and easy maintenance of all parts. Construction Requirements · Blower wheel shall be metallic. · Unit shall have an ECM motor. · Backdraft damper shall be integrated to the unit. · The unit's blower shall be protected by a grille. · Filter shall be accessible without a tool. · Unit's housing and door shall be paintable and made of 24 ga galvannealed steel. · Unit shall include a washable metallic filter. · Unit shall allow 2-in. thick MERV filters in option. · Unit's width shall not exceed 10.25". · Unit's height shall not exceed 10". · Unit's housing's length shall not exceed 14.75". · Unit's weight shall not exceed 12 pounds. Quality Requirements · All plastic parts in the airflow shall be UL94 HB fire rated. · Electrical enclosure shall be in plastic to prevent condensation and UL94 5VA fire rated. · Unit's housing shall be insulated and not show any thermal bridge to the metallic housing. · Unit's insulation shall be made of expanded polystyrene and UL94 HF-2 fire rated. · Unit conforms to UL 507 requirements including those for appliances for use in "other spaces used for environmental air" (Sections 212 - 214) in conformity with the National Electric Code Article 300.22 (c)(3). (applies to FIN-180B-HW model only) · Unit shall be protected by a 5-year warranty. · Unit shall be ENERGY STAR and HVI rated. · Unit shall be ASHRAE 62.2-2010 and 2016 IRC/IMC compliant. · Unit shall be certified by an independent laboratory. · Manufacturer shall be ISO 9001-2015. · Manufacturing plant shall be located in North America. Installation requirements · Unit shall fit between 12-in. cc joists. · Unit shall be designed to be connected with central ventilation or to be used in a standalone installation. · Unit shall be suitable for ceiling hung, ceiling mounted, attic mounted, wall mounted and flush-to-ceiling installation. · Unit shall be designed to be installed in any orientation. · Unit's ports shall be 6-in. round with bumps to maintain a tie-wrap in place. FIN-180Bd062022Adobe PDF Library 16.0.7 Adobe InDesign 17.2 (Windows)