User Manual for SKYDANCE models including: S1-B, AC Triac RF and Push Dimmer, S1-B AC Triac RF and Push Dimmer, Triac RF and Push Dimmer, RF and Push Dimmer, Push Dimmer, Dimmer
RF dimming/Leading edge or trailing edge/Min brightness settable/Push Dim/Wall junction box mounting.
Compatible Load Types Load Type Maximum Load Remarks Due to variety of LED lamp designs, maximum number of LED lamps is further dependent on power factor result when connected to dimmer.
AC Triac RF + Push Dimmer Model No.: S1-B RF dimming/Leading edge or trailing edge/Min brightness settable/Push Dim/Wall junction box mounting Features RF + Push AC phase-cut dimmer, 1 channel output. To dim and switch single color dimmable LED lamps, traditional incandescent and halogen lights. 256 levels 0-100% dimming smoothly without any flash. Leading edge dimming or trailing edge dimming set by dip switch. Min brightness can be set by key. Light on/off fade time 3s selectable. Compatibility with RF 2.4G single zone or multiple zone dimming remote control. Connect with external push switch to achieve on/off and 0-100% dimming function. Easy to be placed in standard wall junction box behind a push switch. Over-heat / Over-load protection, recover automatically. Technical Parameters LVD Input and Output Input voltage Output voltage Output current Output power AC100-240V AC100-240V Max 1.5A 150-360W Dimming data Input signal RF Control distance Dimming level Dimming range RF 2.4GHz + Push Dim 30m(Barrier-free space) 256 levels 0 -100% Safety and EMC EMC standard (EMC) Safety standard(LVD) Radio Equipment(RED) Certification Warranty Warranty ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4 EN 62368-1:2020+A11:2020 ETSI EN 300 328 V2.2.2 CE,EMC,LVD,RED 5 years Environment Operation temperature Case temperature (Max.) IP rating Ta: -30 OC ~ +55 OC T c: +85OC IP20 Weight Weight unit(g) Net weight 48g Gross weight 61g Compatible Load Types Load Type Dimmable LED lamps Maximum Load 200W @ 220V 100W @ 110V Triac Dimmable LED drivers 200W @ 220V 100W @ 110V Incandescent lighting, HV Halogen lamps 400W @ 220V 200W @ 110V Remarks Due to variety of LED lamp designs, maximum number of LED lamps is further dependent on power factor result when connected to dimmer. Maximum permitted number of drivers is 200W divided by driver nameplate power rating, and make sure the surge current is no more than 2 times 65A. User Manual Ver 1.0.7 S1-B AC Triac RF + Push Dimmer Mechanical Structures and Installations AC Push switch Match / Min brightness set key DIP switch for Leading edge or trailing edge phase-cut select AC N output AC L output ON A2 A1 Match Min set 100-240 VAC OUTPUT LN INPUT LN AC L input AC N input Push Switch 52.00 mm 52.00 mm 26.00 mm Typical Wall Junction Box Mounting Wiring diagram Caution: Please carefully ensure all wire connections and polarities are correct and secure before applying power, otherwise this dimmer will be damaged. Push Switch Push Switch Push Switch Push Switch Push Switch Push Switch ON A2 A1 Match Min set 100-240 VAC S1-B OUTPUT LN INPUT LN ON A2 A1 Match Min set 100-240 VAC S1-B OUTPUT LN INPUT LN Dimmable LED light Connect with dimmable LED light Triac Dimmable LED Driver LED light Connect with Triac dimmable LED driver Note: When calculating the maximum number of load lamps or drivers, the input power or input current parameters of a single lamp or driver must be used, the output power parameters can not be used. In addition, the maximum surge current of the dimmer is 65A, the sum of surge current of multiple dimmable LED drivers should not exceed 2 times. otherwise, the product will be overloaded and damaged. Page 1 Leading edge or trailing edge dimming setting Select leading edge(forward-phase) dimmer or trailing edge(reverse-phase) dimmer according to dimmable LED light or driver. ON Reverse-phase Forward-phase Caution: before power on, you must confirm the selection of dip switch. Min brightness setting Long press Min set key for 2s, the light blink 2 times, ready for min brightness set, then short press Min set key 1-6 times, to get 6 min brightness: 5%, 10%, 15%, 20%, 25% or 30%, the light will output the current min brightness immediately, Long press Min set key for 2s or wait 8s, quit min brightness set, the light will output 100% brightness automatically. Light on/off fade time Long press Match key 5s, then short press Match key 3 times, the light on/off time will be set to 3s, the indicator light blink 3 times. Long press Match key 10s, restore factory default parameter, the light on/off time also restore to 0.5s. Match Remote Control (two match ways) End user can choose the suitable match/delete ways. Two options are offered for selection: Use the controller's Match key Use Power Restart Match: Short press Match key, immediately press on/off key (single zone remote) or zone key (multiple zone remote) of the remote. Match: Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote. The light blinks 3 times means match is successful. Delete: Press and hold Match key for 5s to delete all match, The light blinks 5 times means all matched remotes were deleted. Delete: Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote. The light blinks 5 times means all matched remotes were deleted. User Manual Ver 1.0.7 Application notes 1. All the receivers in the same zone. S1-B AC Triac RF + Push Dimmer 30m 30m 30m RF remote Auto-transmitting: One receiver can transmit the signals from the remote to another receiver within 30m, as long as there is a receiver within 30m, the remote control distance can be extended. Auto-synchronization: Multiple receivers within 30m distance can work synchronously when they are controlled by the same remote. Receiver placement may offer up to 30m communication distance. Metals and other metal materials will reduce the range. Strong signal sources such as WiFi routers and microwave ovens will affect the range. We recommend for indoor applications that receiver placements should be no further apart than15m. 2. Each receiver(one or more) in a different zone, like zone 1, 2, 3 or 4. Zone 1 Zone 2 Zone 3 Zone 4 30m 30m Push Dim Function RF remote Short press: Turn on or off light. Long press (1-6s): Press and hold to step-less dimming, With every other long press, the light level goes to the opposite direction. Dimming memory: Light returns to the previous dimming level when switched off and on again, even at power failure. Malfunctions analysis & troubleshooting Malfunctions No light No response from the remote Causes 1. No power. 2. Wrong connection or insecure. 1. The batter y has no power. 2. Beyond controllable distance. 3. The controller did not match the remote. Troubleshooting 1. Check the power. 2. Check the connection. 1. Replace batter y. 2. Reduce remote distance. 3. Re-match the remote. Page 2Corel PDF Engine Version 16.1.0.843 CorelDRAW X6