Newtech | Innovative Bathroomware Products & Design in New Zealand
Instruction Manual for NewTech models including: 8030, Sorano Rimless Toilet Suite, 8030 Sorano Rimless Toilet Suite
File Info : application/pdf, 12 Pages, 3.09MB
DocumentDocumentInstallation Instructions TOILET Sorano Rimless Toilet Suite NOTE: Our Back-to-Wall toilet suites are suitable for both a rear & side entry water inlet. BEFORE YOU BEGIN Before proceeding with installation, please read these instructions carefully to familiarise yourself with the required tools, materials and installation sequences. Please leave these instructions for the consumer after installation. Prior to installation, inspect the toilet to ensure that no damage has occurred in transit. If damage has occurred, or a visible defect exists, do not proceed with installation, and advise your supplier immediately. CAUTION: Risk of personal injury or product damage. Handle with care. Vitreous china can break or chip if the product is handled carelessly. · Observe all local plumbing and building codes. Installation shall be in accordance with AS/NZS 3500 and AS/NZS 6400. · Carefully inspect the new toilet for damage. SORANO TOILET BACK TO WALL | 2 PARTS IDENTIFICATION 300mm hose for Top/Rear install (supplied with cistern) Side Entry Capping Plus Side Inlet Valve (for Top Rear and Lower Entry supplied with cistern) Bottom Entry Connector (supplied with cistern) Cistern Bung (supplied with cistern) Plus: ± Pan Fixing Kit (supplied) 23 D Pan Cistern Connecting Bolts (supplied with cistern) Supplied Pack A: ± 2 x Stainless Steel Bolts and Rubber Seal Supplied Pack B: ± 4 x Stainless Washer ± 2 x Stainless Nut ± 2 x Stainless Wing Nut SORANO TOILET BACK TO WALL | 3 PREPARING TO INSTALL 1. Identify the type of toilet installation A) Side Entry with Bottom Inlet or B) Top Rear Entry with Side Inlet Valve for Side Entry toilets, the bottom Entry Connector is supplied with the cistern. Bottom Entry Connector Seal Washer Nut A) Bottom inlet cistern configuration Top Rear Entry Fixing Screw Washer Seal Washer Nut Cistern Inlet Hose Bung B) Top Rear Entry cistern configuration Side Inlet Valve Fixing Screw Washer Seal Washer Nut Important: Please ensure and check the bung is tight. We recommend using a small bead of silicon to ensure seal. For Top Rear Entry installations, skip to Pan Installation on page 6 For Side Entry/Bottom Inlet installations, proceed with instructions, below 2. For Side Entry/Bottom Inlet installations, check the shut-off valve position. Side entry hole Shut-off valve Left-hand valve position Side entry hole Shut-off valve Right-hand valve position SORANO TOILET BACK TO WALL | 4 CISTERN INSTALLATION - BOTTOM INLET Skip this page if installing a Top Rear Entry cistern configuration. 1. Install the Bottom Entry Connector to the cistern. Place the stainless steel bolt with the rubber seal through fixing holes and tighten with stainless steel washer and nut beneath cistern. Ensure bottom entry bungs are a tight mechanical seal. We recommend also using silicon to ensure seal. Bottom Entry Connector Seal Washer Nut Fixing Screw Washer Seal Washer Nut Important Please ensure and check the bung is tight. We recommend using a small bead of silicon to ensure seal. 2. Position the cistern over the gasket on the pan inlet. Securely tighten the cistern bolts using a washer and stainless wing nut. Gasket Screw Pan Inlet Washer Wing nut 3. Connect the supply hose to the cistern inlet and feed the hose through the appropriate side hole in the pan. Side Entry Holes Water Supply Hose (Not supplied) 4. Connect the supply hose to the shut-off valve to test the system for leaks. Shut off the water supply and disconnect the hose. Insert a capping plug into the unused hole. Capping Plug SORANO TOILET BACK TO WALL | 5 PAN INSTALLATION 1. Define the position of the connector: Place the connector onto the pan, and position the connector between the outlet and waste pipe. Installation instructions are supplied with each respective pan connector. Finished Wall Pan Vario Connector Offset Pan Collar Setout 2. Mark the positions of the floor fixing kit holes. Wall Template Fixing hole locations N.B. If floor has had waterproof membrane applied, we recommend just siliconing the pan to the floor. SORANO TOILET BACK TO WALL | 6 3. Drill fixing holes at the marked locations on the floor and insert the anchors where required. Hexagon Lag Screw Bracket Hole Anchor Washer Anchor Cap Sleeve Screw 4. Place a washer onto each of the hexagon screws and fix the brackets to the floor. 5. Position the toilet in the marked location, while ensuring an effective connection is made with the pan connector. 6. Install the plastic screw sleeves and use the screws to fix the toilet to the brackets. Attach the chromed caps to the screw heads. SORANO TOILET BACK TO WALL | 7 CISTERN INSTALLATION - TOP REAR ENTRY Skip this page if installing a Bottom Inlet cistern configuration. 1. Place the stainless steel bolt with the rubber seal through fixing holes and tighten with stainless steel washer and nut beneath cistern. Ensure bottom entry bungs are a tight mechanical seal. We recommend also using a silicon to ensure seal. Top Rear Entry Cistern Inlet Hose Bung Side Inlet Valve Fixing Screw Washer Seal Washer Nut Important Please ensure and check the bung is tight. We recommend using a small bead of silicon to ensure seal. 2. Position the cistern over the gasket on the pan inlet. Securely tighten the cistern bolts using a washer and stainless wing nut. Gasket Screw Pan Inlet Washer Wing nut 3. Connect the supply hose to the cistern inlet, connect the hose to the water supply shut-off valve and check for leaks. Cistern Inlet Hose (supplied) Side Entry Holes 4. Insert cappling plugs into the side entry holes in the pan. 5. Connect the supply hose to the shut-off valve to test the system for leaks. Shut off the water supply and disconnect the hose. SORANO TOILET BACK TO WALL | 8 PUSH BUTTON INSTALLATION Fit the lid and test the buttons. Adjust the rods as required. FLUSH VALVE REMOVAL AND INSTALLATION Flush Valve A 1. Release flush valve by turning anti-clockwise and pulling straight up on the canister. 2. Assemble flush value by pushing straight down into the canister and turning clockwise. 2 1 1 2 SORANO TOILET BACK TO WALL | 9 TOILET SEAT INSTALLATION · Before installation, please check all parts are included and match the images below. SEAT FITTINGS 4. Before attaching the seat, move mounting bases so posts align with holes in the back of the seat. 9. Align the posts and carefully lower seat back into place (`click' will be heard). 11. To remove the seat, press the quick release button (`click' will confirm) and open seat & lid to vertical position. SORANO TOILET BACK TO WALL | 10 TOILET SEAT CLEANING INSTRUCTIONS · We recommend cleaning the toilet seat with warm soapy water, then drying with a clean soft cloth. CAUTIONS · Exposure of toilet seat to direct sunlight for an extended amount of time may cause fading. · Do not place heavy objects on the toilet seat cover, as this can lead to damage. · Do not clean the toilet seat with strong chemical cleaners or citrus based cleaners. · Do not close the toilet seat forcefully. This can cause damage to the soft-close mechanism. NOTES Do not force closure of the seat or lid, allow mechanism to close naturally. Be careful of damaging the toilet seat. This includes standing on the toilet seat, or overloading the toilet seat, which can result in broken hinges. SORANO TOILET BACK TO WALL | 11 FINALISING INSTALLATION 1. Ensure front edge of seat follows the shape of the front edge of the pan. 2. Ensure silicon rubber washer is fitted between seat connector and pan to ensure seat is rigid. 3. Make final connection of water supply hose to shut-off valve. 2 Test the system for leaks. 4. Apply a suitable sealant between the pan and adjacent surfaces. 1 3 Head Office 281 Heads Road, Wanganui PO Box 2050, Wanganui sales@newtech.co.nz Auckland Showroom 525 Great South Road, Penrose, Auckland aucklandshowroom@newtech.co.nz 0800 728 662 www.newtech.co.nz SORANO TOILET BACK TO WALL | 12