strength.it
Instruction Manual for Direct Ptt models including: M995, 2A9QQ-M995, 2A9QQM995, 2A9QQ-M995 In-Vehicle POC Network Mobile Radio, 2A9QQ-M995, In-Vehicle POC Network Mobile Radio, Network Mobile Radio, Mobile Radio, Radio
Direct PTT, Inc. M995 In-vehicle PoC Network Radio 2A9QQ-M995 2A9QQM995 m995
M995 In Vehicle Po C Network Radio by Direct PTT
File Info : application/pdf, 11 Pages, 3.91MB
DocumentDocumentM995 In-Vehicle POC Network Mobile Radio Radio Body LCD Display Menu Function Operation 1.Contracts Group Call Individual Call/Single Call Good Friends Call 2.Settings LCD Backlight LCD Light Level Key Backlight Network Mode 3.Sound Key Tone Talk Tone Voice CodeMIC Gain SPK Gain 4.GPS Function 5.SIM CARD 6.Device Info In-vehicle Radio Body 4G Antenna GPS Antenna Power Supply Cable Metal Bracket Speaker MIC Instruction Manual Diagram 1.Volume Control Knob & Power ON/ OFF Button Please long press it to power ON or power OFF the radio. Turn the volume knob clockwise to increasethe volume level, turn the volume knob counter-clockwise to reduce the volume level. 2.LED Indicator It lights Yellows for few seconds during power on. It lights RED during transmitting. It lights GREEN during the receiving. 3.Emergency Alarm Please long press this button to activate the emergency alarm/SOS function, long press again to exit. 4.Speaker MIC Connector Please insert air plugs MIC speaker with 8 pinholes, press and hold the PTT button, the radio will bleep and LED indicator will turn RED (that meanstransmitting is valid),then speak clearly into the microphone with your normalvoice(remember to keep the MIC around 2.5~5CM from your mouth) 5.LCD Display Kindly note: this is non-touching screen. 6.Functional Key. Please short press to UP the groups and long press to enter into Network Mode selection 7.Functional Key Please short press to DOWN the groups and long press to switch the Backlights Mode. 8.UP/DOWN/LEFT/RIGHT Key Please press it to choose the desired items from menu. 9.Menu Key(Green --) 10.Backup Key(Red -) 11.MIC Speaker 12.GPS Antenna Connector 13.4G Antenna Connector 14.Power Supply Connector Kindly note: Please connect to 12V/24V AC Power from car. 15.Headset/Earpiece Connector . 16.Micro USB Programming Cable Connector Please long press functional key - - and functional key - at the same time and turn ON the radio device, it will enter into writing mode SET ACCOUNT GV7.A.2.ZZD ID: sfetest1 17.SIM CARD 1 Kindly note: It only supports Micro sim card. Please refer to the corner, aware inserting the sim card in right side. 18.SIM CARD 2 Kindly note: It only supports Micro sim card. Please refer to the corner, aware inserting the sim card in right side. LCD Display abcd Tue Carrier Network Signal Strength.It indicates valid carrier network signal strength Current Network Mode. Please long press functional key - - to enter intonetwork mode settings. SIM Card Indicator: Current working on SIM CARD 1 Backlight Auto Mode. Diplay current local time indicates backlight always ON. Current Group Name Tue Current Week Day Current Own User Name Current Date CALLING... test test Tue Tue Idle Status Transmitting Status sfetest10 test Tue Receiving Status Basic Settings Contracts CONTACTS SETTING SOUND LOCATION CARD DEVICE INFO SET BACK GROUPS MEMBERS GOOD FRIENDS SET BACK Group Call 1.Press to enter into MENU list 2.Select [CONTRACTS] and press to confirm and enter; 3.Select [GROUPS]and press to confirm and enter; 4.Press to select target group and press to confirm. ( UP, DOWN, revert to front page, revert to next page) Individual Call/Single Call 1.Press to enter into MENU list 2.Select [CONTRACTS] and press to confirm and enter; 3.Select [GROUPS]and press to confirm and enter; 4.Press to select target group and press to confirm. ( UP, DOWN, revert to front page, revert to next page) Good Friends Call 1.Press to enter into MENU list 2.Select [CONTRACTS] and press to confirm and enter; 3.Select [GROUPS]and press to confirm and enter; 4.Press to select target group and press to confirm. ( UP, DOWN, revert to front page, revert to next page) Settings LCD BACK LIGHT AUTO LCD LIGHT LEVEL 3 KEY BACK LIGHT AUTO NET MODE SET BBAACCKK LCD Backlight 1.Press to enter into MENU list; BACK 2. Select [SETTINGS] and press to confirm and enter; 3.Select [LCD BACK LIGHT] and press to confirm and enter; 4. Press to switch between (Auto Mode) and cAlways ON LCD Light Level 1.Press to enter into MENU list, 2.Select [SETTINGS] and press to confirm and enter; 3. Select [LCD LIGHT LEVEL] and press to confirm and enter; 4.Press to select the desired backlight level ( Range from level 1~level 5). Key BackLight 1.Press to enter into MENU list, 2.Select [SETTINGS] and press to confirm and enter; 3.Select [KEY BACK LIGHT] and press to confirm and enter; 4.Press to switch between AUTO and ON. Network Mode 1.Press to enter into MENU list, 2.Select [SETTINGS] and press to confirm and enter; 3.Select [NETWORK MODE] and press to confirm and enter; 4.Press to switch between 4G Only,3G Only,2G Only and AUTO mode. Sound Key Tone Talk Tone Voice code MIC Gain 5 SPK Gain SET Set Set 4K 3 3 BACK Key Tone 1.Press to enter into MENU list, 2.Select [SOUND] and press to confirm and enter; 3.Select [KEY TONE] and press to confirm and enter; 4.Press to switch ON or OFF. Talk Tone 1.Press to enter into MENU list, 2.Select [SOUND] and press to confirm and enter; 3.Select [KEY TONE] and press to confirm and enter; 4.Press to switch ON or OFF. Voice Code 1.Press to enter into MENU list, 2.Select [SOUND] and press to confirm and enter; 3.Select [VOICE CODE] and press to confirm and enter; 4.Press to switch between 4K and 8K MIC Gain 1.Press to enter into MENU list, 2.Select [SOUND] and press to confirm and enter; 3.Select [MIC GAIN] and press to confirm and enter; 4.Press to select the desired MIC gain level. ( Range from level 1~ level 6) SPK Gain 1.Press to enter into MENU list, 2.Select [SOUND] and press to confirm and enter; 3.Select [SPK GAIN] and press to confirm and enter; 4.Press to select the desired speaker gain level. ( Range from level 1~ level 6) GPS Function Location View: COG: SPD: ALT LAT: LON: SET BACK 1.Press to enter into MENU list, 2.Select [LOCATION] and press to confirm and enter. SIM CARD SIM CARD 1 SIM CARD 2 AUTO SET 1.Press to enter into MENU list, BACK 2.Select [SIM CARD] and press to confirm and enter; 3.Press to switch between SIM CARD 1, SIM CARD 2 and AUTO. Device Info - SOFT Ver: GV7.A.2 ZZD SET BACK 1.Press to enter into MENU list, 2.Select [DEVICE INFO] and press to confirm and enter. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.