Automotive OEM integration | CRUX Interfacing Solutions
Instruction Manual for CRUX models including: RVCCH-75DC, Backup Camera System, RVCCH-75DC Backup Camera System
Crux RVCCH-75DC Backup Camera System Add a rear-view camera to your factory radio in select 2013-up Ram vehicles at Crutchfield
Crux RVCCH-75D | Backup Camera Integration Kit for 2013-2016 R...
File Info : application/pdf, 3 Pages, 1.39MB
DocumentDocumentINTERFACING SOLUTIONS R Sightline Multi View Integration RVCCH-75DC Rear View Integration Interface with VIM for DODGE RAM Trucks · Adds reverse camera input to the Uconnect Touchscreen Radio · Aftermarket tailgate handle camera included · Automatically switches to Rear-view when car is in Reverse mode · Plug & Play Installation RVCCH-75DC Module RVCCH-75DC Harness CDR-02 Camera RVC Video Signal Input OEM Radio Harness Connect RCAs and secure with tape all around 20 Ft. Coax Cable Regulator Line up Arrows RED Wire BLACK Wire RED Wire Tape Off (Not Used) Push in Connectors all the way WHITE Wire OR* (Camera Power Output +12V 250mA) Source Ground WHITE Wire Parking Guideline BLACK (Ground) *Connect BLACK (ground) wire to a source ground and not chassis ground (i.e. ground wire on reverse light) If video noise is present, we recommend connecting the ground wire to the BLACK ground wire on the RVCCH-75DC harness. ON DP 8-Pin Molex Represents Solder Joint To Radio DIP LED* SWITCH *LED RED = Power ON Status LED BLUE = Data Bus ON Status 1 of 3 Crux Interfacing Solutions · Chatsworth, CA 91311 phone: (818) 609-9299 · fax: (818) 996-8188 · www.cruxinterfacing.com rev.09222021 INTERFACING SOLUTIONS R Sightline Multi View Integration RVCCH-75DC Rear View Integration Interface with VIM for DODGE RAM Trucks DIP SWITCH FUNCTIONS: DIP 1 = Set to OFF DIP 2 = Rear View Camera ON / OFF DIP 3 = Set to OFF DIP 4 = Set to OFF DIP 5 = Defaulted to OFF* DIP 6 = Defaulted to ON* *DIP 5 & 6 If the radio is having turn-on issues, please try the following: Attempt 1: Set 5 & 6 to ON Attempt 2: Set 5 to ON and 6 to OFF Attempt 3: Set 5 to OFF and 6 to ON ON 12 34 56 INSTALLATION INSTRUCTIONS: INSTALLING THE CDR-02 CAMERA AND CABLE 1. Remove the OE tailgate handle. 2. Remove the OE lock cylinder and install in the CDR-02 camera housing. 3. Install the new tailgate handle and run the cables to the radio. 4. Remove the factory radio to gain access to the factory connectors. 5. Route the wires towards the radio and make the power and video connections. For powering up the camera, use the 12V OUTPUT (White Wire). (See Wiring Diagram on page 1) 6. Connect the camera ground wire to chassis ground. If video noise is present, we recommend connecting a ground wire from the camera to the BLACK wire on the RVCCH-75DC T-harness. 7. The CDR-02 has a built-in parking guide lines option and is defaulted to ON from the factory. To turn OFF the parking guide lines, cut the thin WHITE wire located on the camera cable 4 feet from the camera. Unplug the barrel connectors on the cable for 10 seconds. Align the arrows on the barrel connectors and firmly plug them together. 8. Test the camera before re-installing the radio. CODING THE RADIO FOR A REAR VIEW CAMERA The radio has to be coded to accept a reverse camera. Please follow the coding procedure below: 1) Turn key off and remove the key from ignition. 2) Open the driver door then close it (make sure all doors, lift gate and hood are also closed). 3) Look at the module and wait for LEDs to turn off then disconnect the module. 4) Before plugging back the module, turn all DIP switches to ON then OFF. 5) Set DIP switches to the settings provided above. 6) Reconnect module and wait for the LEDs to turn off. 7) Start engine and the coding operation is now complete. 8) Put the gear in reverse to test the camera. 2 of 3 Crux Interfacing Solutions · Chatsworth, CA 91311 phone: (818) 609-9299 · fax: (818) 996-8188 · www.cruxinterfacing.com rev.09222021 INTERFACING SOLUTIONS R Sightline Multi View Integration RVCCH-75DC Rear View Integration Interface with VIM for DODGE RAM Trucks RAM 2013 - 2017 2013 - 2017 2013 - 2017 1500 2500 3500 NOTES: 1. Not compatible with diesel powered trucks. 2. Not comptible with RAM trucks with factory installed cargo camera. COMPATIBLE RADIOS: 8.4" Screen with Separate Knobs 5" Screen with 6 Buttons & Separate Knobs 4.3" Screen with 6 Buttons & 2 Knobs Not compatible radio 4.3" Screen with 4 Buttons & 2 Knobs 3 of 3 Crux Interfacing Solutions · Chatsworth, CA 91311 phone: (818) 609-9299 · fax: (818) 996-8188 · www.cruxinterfacing.com rev.09222021