Electric Fireplace

Important Instructions

Thank you for choosing our Electric Fireplace. This owner's manual provides valuable information for the proper care and maintenance of your new product. Please read the instructions carefully to familiarize yourself with all operational aspects.

When using this electric unit, follow basic safety precautions to reduce the risk of fire, electric shock, and injury:

1. Read ALL instructions before using this unit.
2. The heater can get hot. To avoid burns, DO NOT let bare skin touch hot surfaces. Use handles if provided.
3. Keep combustible materials (furniture, pillows, bedding, paper, clothes, curtains) at least 3 ft from the front of the heater and away from the sides, top, and rear. DO NOT place towels or other objects on the heater.
4. To prevent electric shock or fire, do not insert foreign objects into any ventilation or exhaust opening. Do not use on soft surfaces like a bed where openings may become blocked.
5. DO NOT run the cord under carpeting or cover it with rugs. Arrange the cord away from traffic areas to prevent tripping.
6. This heater is not intended for use in bathrooms, laundry areas, or similar indoor locations. NEVER locate the heater where it may fall into a bathtub or other water container. DO NOT immerse in water or other liquids.
7. DO NOT touch the control panel or plug with wet hands.
8. Exercise extreme caution when the heater is used by or near children or disabled persons, or when left operating and unattended.
9. The heater has hot and arcing or sparking parts inside. DO NOT use in areas where gasoline, paint, explosive, or flammable liquids are used or stored. Keep the unit away from heated surfaces and open flames.
10. CAUTION: Risk of Electric Shock. DO NOT open or attempt to repair the heater yourself.
11. DO NOT operate any heater with a damaged cord or after it malfunctions, has been dropped, or damaged. Contact after-sales service for assistance.
12. Use only for intended household use as described in this manual. Other uses not recommended by the manufacturer may cause fire, electric shock, or injury. Use of attachments not sold by the manufacturer may cause hazards.
13. DO NOT attempt to repair or adjust any electrical or mechanical functions. Doing so will void your warranty. The unit contains no user-serviceable parts. Qualified personnel should perform all servicing.
14. WARNING: To reduce the risk of fire or electric shock, DO NOT use this unit with any solid-state speed control device.
15. Always plug heaters directly into a wall outlet receptacle. Never use with an extension cord or relocatable power tap.
16. To avoid fire or shock hazard, plug the unit directly into a 120 V AC electrical outlet.
17. Connect to properly grounded outlets only.
18. To disconnect the heater, turn controls to OFF, then remove the plug from the outlet. Pull firmly on the plug, DO NOT pull on the cord.
19. Always unplug the unit before moving or cleaning, or when the heater is not in use.
20. Always use on a dry, level surface. Use on the floor only.
21. DO NOT use outdoors.

SAVE THESE INSTRUCTIONS

Specifications

Safety Features

Overheat Safety Feature

This heater is equipped with an overheat safety feature. When the heater's internal components reach a certain temperature that could cause overheating and possible fire, the heater will automatically shut off.

WARNING: It is normal for the power cord to feel warm to the touch; however, a loose fit between the outlet and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a different outlet. Contact a qualified electrician to inspect the original outlet for damage.

Preparation

This product includes a GLASS panel! Always use extreme caution when handling glass. Failure to do so could result in personal injury or property damage.

Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Parts and assembly steps are grounded for wall-hanging or recessing use. Check the parts list to make sure nothing is missing. Dispose of packaging materials properly. Please recycle whenever possible. You will need the following tools (not included): Phillips screwdriver; stud finder; level; tape measure; electric drill; 1/4" wood drill bit, hammer.

Part List

A: Machine x1

B: Glass x1

C: Remote control x1

D: Feet left x1

E: Feet right x1

F: Wall mount bracket x1

G: Crystal embers x1

H: Drift wood fire logs x1

I: Small wall-mounted bracket x1

Hardware

Dimensional Drawings

QBL-X36IN-BK

Dimensions: 36" width, 18.11" height, 31.42" depth. Side view: 16.57" height, 3.94" depth.

QBL-Z50IN-BK

Dimensions: 50" width, 18.11" height, 45.39" depth. Side view: 16.57" height, 3.94" depth.

QBL-D60IN-BK

Dimensions: 60" width, 18.11" height, 55.39" depth. Side view: 16.57" height, 3.94" depth.

Control Panel Operation

The control panel features:

1. Digital display: Shows timing, flame color, carbon bed color, flame speed, light brightness, lock status, and "High/Low" heating settings.
2. Timer button: Sets timing for boot or shutdown.
3. Lock button: Press for 3-5 seconds to lock or unlock controls.
4. Speed button: Adjusts flame speed.
5. Dimmer button: Adjusts light brightness.
6. Carbon bed button: Selects ember bed color.
7. Flame button: Selects flame color.
8. Temperature setting button: Sets the desired temperature.
9. Heating button: Selects High heating or Low heating.
10. Power button: Turns the unit on/off.

Remote Control

The remote control offers the following functions:

• Power button: Powers the display on and off.
• Heater button: High heating and low heating settings.
• Dimmer button: Adjusts light brightness.
• Lock button: Press for 3-5 seconds to lock or unlock.
• Carbon bed button: Selects ember bed color.
• Flame button: Selects flame color.
• Temperature buttons (TEMP +/-): Adjust the temperature manually from 59°F to 95°F. Pressing and holding the buttons increases/decreases temperature more quickly.
• Timer button: Sets the timer.
• Recreation mode button: Turns recreation mode on/off.
• Sleep mode button: Turns sleep mode on/off.

Remote Control Battery Installation:

1. Remove the battery box cover.
2. Insert two new AAA alkaline batteries, ensuring correct polarity (+/-).
3. Reinstall the cover.

Control Panel/Remote Control Functions

Ensure the electric fireplace is properly assembled and connected to an electrical outlet. The power button light should be on, indicating it is ready to operate.

1. Start and select working mode

In standby status, the power button light is red. Other function buttons are off. Press the power button to turn the machine on. Other function buttons can now be set. Pressing the power button again turns the machine off and returns it to standby status.

2. Start and select working mode (Heating)

Select a heat setting by pressing the HEATER button to toggle between High (HI) and Low (LO) heat settings, or turn heating off. High heat mode power is 1500W, Low heat is 750W.

3. Setting room temperature

Adjust the thermostat using the arrows on the control panel or remote control. The temperature indication varies from 59°F to 95°F. Once the desired temperature is set, the heater will remain on until the room temperature reaches the set temperature. The heater will cycle on and off to maintain the desired room temperature.

4. Setting Flame Color

Press the flame button to cycle through 14 flame colors (F1-F14). Each color lasts for 3 seconds and changes in a cycle. The colors include yellow green, red, blue, green, purple, cyan, orange, pink, light blue, light green, light purple, light white, yellow, and cycle colors.

5. Setting Carbon bed Color

Press the carbon bed button to cycle through 14 carbon bed colors (C1-C14). Each color lasts for 3 seconds and changes in a cycle. The colors include yellow green, red, blue, green, purple, cyan, orange, pink, light blue, light green, light purple, light white, yellow, and cycle colors.

6. Flame dimmer setting

The flame brightness is adjustable in five levels (L5-L0). L5 is the brightest, and L0 turns the light off. Pressing the dimmer button cycles through the brightness levels. This setting affects both the flame and carbon bed light brightness.

7. Flame speed setting

When the machine is turned on, the flame speed is set to the fastest mode (S5). Press the speed button to adjust the flame speed from fastest (S5) to slowest (S1).

8. Lock setting

Press and hold the lock button for 3-5 seconds to activate the lock function, which disables other buttons. Press and hold the lock button again for 3-5 seconds to unlock.

9. Setting timer-power-off

This function can only be set when the unit is powered on. Press the timer button on the control panel or remote control. Adjust the time using the timer button or arrows. The digital display shows time values from 0 to 12 hours (1-hour intervals). The display shows OH, 1H, 2H, ..., 12H.

10. Setting timer-power-on

This function can only be set when the unit is powered off. Press the timer button on the control panel. Adjust the time using the arrows on the control panel or remote control. The digital display shows time values from 0 to 12 hours (1-hour intervals). The display shows 0H, 1H, 2H, ..., 12H.

11. Setting mode

Sleep mode: Available only on the remote control. Activates the slowest flame speed and darkest light, ideal for sleeping.

Recreation mode: Available only on the remote control. Activates the fastest flame speed and brightest light. The flame and carbon bed colors change automatically. Press the Recreation button again to turn off the function and stop the changes.

Assembly Way Choose

This product has 3 installation ways: Wall Mounted, Free Standing with Feet, Recessed into the Wall.

Installation Scheme 1: Wall Mounted

WARNING: ONLY QUALIFIED PERSON CAN PERFORM THE INSTALLATION.

Due to various wall finish materials, consult your local builder before installing. Select a location that is not prone to moisture and is at least 36" away from combustible materials (curtains, drapes, furniture, bedding, paper, etc.).

Instructions:

1. Select a location that is not prone to moisture and is at least 36" away from combustible materials.
2. Have two people hold the fireplace against the wall to determine the final location.
3. Mark the position of the Wall-mount bracket (F) on the wall. Ensure the hooks on the bracket face outward and are level. Secure the bracket (F) to the wall using 4 drywall anchors (1) and 4 screws (2).
4. Place the unit with the front facing downward on a soft, non-abrasive surface. Install the 2pcs Small wall-mounted brackets (I) on the back of the fireplace using 4pcs Self-tapping screws (4). (Note: The 60-inch fireplace uses 4 Small wall-mounted brackets (I) and 8 Self-tapping screws (4)).
5. Remove the glass panel by unscrewing the screws on both sides. Keep the screws. Remove the Crystal embers (G) and Driftwood fire logs (H) and set aside. Reinstall the glass panel using 2pcs Self-tapping screws (4) and the saved screws. Verify the glass panel is secure. Tear off the protective film on the glass.
6. Hang the fireplace on the bracket (F). Be careful not to tilt the fireplace to prevent shifting the Crystal embers (G) and Driftwood fire logs (H). Check the stability of the fireplace. Use 2pcs Self-tapping screws (4) through the small holes on both sides of the bracket (F) to secure the fireplace to the wall.

Installation Scheme 2: Free Standing Feet Assembly Way

1. Remove the glass panel as described in Installation Scheme 1, step 5. Set aside the Crystal embers (G) and Driftwood fire logs (H). Reinstall the glass panel using 2pcs Self-tapping screws (4) and the saved screws. Verify the glass panel is secure. Tear off the protective film on the glass.
2. Place the heater on a flat and clean location. Take out the feet (D & E) and screws (3) from the box and assemble the feet as shown in the diagrams.

Installation Scheme 3: Recessed Installation

Consult your local builder before installing. Select a location that is not prone to moisture and is at least 36" away from combustible materials.

To prevent exposed insulation or vapor barrier contact, finish the fireplace enclosure walls (e.g., Sheetrock, drywall). This ensures clearance to combustibles within the wall cavity.

Never install fireplace into load-bearing walls. Recess into non-load bearing walls ONLY!

Instructions:

1. Choose a location in the wall to install the fireplace.
2. Create an opening in the wall that is no more than 1¼” larger than the metal firebox portion of the fireplace.

Choosing Installation Location

Measure the wall location to ensure the fireplace fits. Minimum clearances (from the front of the glass panel):

• Bottom of Fireplace to Floor: 200mm
• Sides of Fireplace: 0
• Back of Fireplace: 0
• Top of Fireplace to Mantel: 300mm
• Top of Fireplace to TV: 300mm
• Top of Fireplace to Ceiling: 300mm

Remove the glass panel prior to installation as per instructions.

FIG. 1

1. Stand the fireplace up, then remove the glass panel by unscrewing the screws on both sides. Keep the screws.

FIG. 2

2. Take out the Crystal embers (G) and Driftwood fire logs (H), place them on the ember bed. Reinstall the glass panel using 2pcs Self-tapping screws (4) and the saved screws. Verify the glass panel is secure. Tear off the protective film on the glass.

Care, Cleaning and Maintenance

Cleaning:

• Always turn the heater off and unplug the power cord before cleaning, performing maintenance, or moving the fireplace. Failure to do so could result in electric shock, fire, or personal injury.
• Never immerse in water or spray with water.

Metal:

Buff using a soft cloth, slightly dampened with citrus oil-based product. Do not use brass polish or household cleaners, as these products will damage the metal trim.

Glass:

Use a good quality glass cleaner sprayed onto a cloth or towel. Dry thoroughly with a paper towel or lint-free cloth. Never use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.

Vents:

Use a vacuum or duster to remove dust and dirt from the heater and vent areas.

Plastic:

Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water. Never use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.

Maintenance:

Risk of electric shock! Do not open any panels. No user-serviceable parts inside! Always turn the heater off and unplug the power cord before cleaning, performing maintenance, or moving the fireplace.

Electrical and Moving Parts:

The fan motors are lubricated at the factory and will not require lubrication. Electrical components are integrated and not serviceable by the customer.

Storage:

Unplug the fireplace when not in use and store it in a clean and dry place.

Technical Support

Phone: (909)637-7665 | (909)637-7593

Email: HJ-Customer-Service@outlook.com

Thank you for choosing this product. We strive to provide the best quality products and services. Should you have any issues, please do not hesitate to contact us.