Soldering and Rework equipment for electronics | JBC SolderingWarranty Extension
Instruction Manual for JBC models including: AN115 Adjustable Nano Tweezers, AN115, AN115 Nano Tweezers, Adjustable Nano Tweezers, Nano Tweezers, Tweezers
AN115 - Adjustable Nano Tweezers
File Info : application/pdf, 8 Pages, 6.17MB
DocumentDocumentINSTRUCTION MANUAL AN115 Adjustable Nano Tweezers This manual corresponds to the following reference: AN115-A Packing List The following items are included: Adjustable Nano Tweezers .................... 1 unit Manual ......................................................... 1 unit Ref. 0029831 Connections NAU 2-Tool Nano Control Unit* C115 Cartridges* AN115 Adjustable Nano Tweezers Power Socket Main Switch *not included, sold separately 2 Changing Cartridges Save time and change cartridges safely without having to switch the station off. Removing Inserting Aligning 11 C115 C105 / C11 C105 / C115 2 2 Place the cartridge into the extractor slot (1) and pull the tweezers to remove the cartridge (2). Push the tweezers onto the new cartridge until the reference ring*. Use the holes to rotate the cartridges for a proper alignment. No Yes Reference Ring Vertical Cartridge Alignment Reference Ring not aligned *Important For a correct connection, it is important to push the cartridge in until the reference ring rests against the tweezers. aligned Turn the tweezers hand whell forwards or backwards for a vertical cartridge alignment. One tip lines up with the other. 3 Example: Chip Compoments Rework Process using Tweezers and Pedal The Pedal is frequently used to rework components with tweezers. AN115, JBCs Adjustable Nano Tweezers, is the most effective tool for desoldering chip components but also it facilitates its rapid placement and soldering by using P405 pedal connected to JBC´s NAS station. 1 ROBOT P405 Pedal connect to the same port Nano Control Unit Tweezers Connections Connect pedal P405 to the same port where AN115 nano tweezers are connected. In the peripherals menu for the "Pedal Activation Mode" choose between "pressed" and "released". 4 2 * "Press Mode" previously selected 3 Desoldering* Lift the tweezers from the holder, press and hold the pedal to activate the tweezers and desolder the component. Once the pedal is released the tweezers enters in hibernation mode and cools down. DS360 Micro Desoldering Iron Pad Cleaning Clean the pads with JBC´s desoldering tool DS360. For this operation JBC´s desoldering station DSS is needed. 4 DPM Manual Solder Paste Dispenser Solder Paste Dispensing Apply the solder paste amount needed to solder the new chip component. The use of JBC´s DPM solder paste dispenser is recommended. 5 5 6 6 Placing Do not press the pedal. Use the tweezers to position the component on the previously tinned pad. Note: The inactive tweezers prevents the component from heating up prematurely. Soldering Once in position press and hold the pedal to activate the tweezers and perform the soldering. Compatible Cartridges The Nano Tweezers NP115 and AN115 work with C115 cartridges. Find the model that best suits your soldering needs on www.jbctools.com Safety Tweezer Conical Bent Tweezer Chisel Blade It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion. - Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire. - The power cord must be plugged into approved bases. Be sure that it is properly grounded before use. When unplugging it, hold the plug, not the wire. - Do not work on electrically live parts. - The tool should be placed in the stand when not in use in order to activate the sleep mode. The soldering tip or nozzle, the metal part of the tool and the stand may still be hot even when the station is turned off. Handle with care, including when adjusting the stand position. - Do not leave the appliance unattended when it is on. - Do not cover the ventilation grills. Heat can cause inflamable products to ignite. - Avoid flux coming into contact with skin or eyes to prevent irritation. - Be careful with the fumes produced when soldering. - Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm. - Utmost care must be taken with liquid tin waste which can cause burns. - This appliance can be used by children over the age of eight and also persons with reduced physical, sensory or mental capabilities or lack of experience provided that they have been given adequate supervision or instruction concerning use of the appliance and understand the hazards involved. Children must not play with the appliance. - Maintenance must not be carried out by children unless supervised. 7 Specifications AN115 Adjustable Nano Tweezers Ref. AN115-A - Cable length: - Total Net Weight: - Package Dimensions /Weight: (L x W x H) Complies with CE standards. ESD safe. 120 cm / 47.24 in 50.6 g / 0.112 lb 237 x 42 x 42 mm / 94.5 g 9.33 x 1.65 x 1.65 in / 0.208 lb Warranty JBC's 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased. Get 1 extra year JBC warranty by registering here: https://www.jbctools.com/productregistration/ within 30 days of purchase. This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility. 0029831-260722