Instruction Manual

Warning and Safety

*Read this guide before installation and using this appliance. Failure to follow the safety instructions may result in property damage, serious injury, or death.

DANGER

Indicates an imminently hazardous situation that, if not avoided, will result in death, serious injury, or serious property damage.

WARNING

Indicates a potentially hazardous situation that, if not avoided, will result in death, serious injury, or serious property damage.

CAUTION

Indicates a potentially hazardous situation that, if not avoided, will result in minor to moderate injury. It may also be used to indicate unsafe practices.

DANGER

• In the case of the appliance emitting smoke or burning smell, shut down the appliance and disconnect from the power supply immediately.
• This appliance uses R32 refrigerant. Handle the air conditioner with care and check if there is any refrigerant leakage. In the case of refrigerant leakage, shut down the appliance and disconnect from the power supply. Contact a qualified technician for inspection. Refrigerant can be toxic and flammable. Rapid evaporation of refrigerant may cause frostbite, cardiac arrhythmia, and / or skin irritation.

WARNING

• This appliance must be plugged directly into a wall power socket. Do not connect this appliance to a power strip, extension cord, surge protector, timers, or direct breaker.
• Ensure the voltage and current rating of the power supply corresponds to that on the product specification.
• Make sure the appliance is connected to a properly grounded power outlet only.
• Do not use the appliance with a damaged cord or plug, or after the appliance malfunctions, has been dropped, or damaged in any manner.
• This appliance is designed to be used indoors only. Do not use this appliance outdoor or expose it to outdoor elements such as rain, snow, sunlight, wind, or extreme temperatures.
• Do not place or use the appliance in the bathroom, laundry area, or places that might come into contact with water.
• Do not use this appliance near flammable substances such as alcohol, gasoline, paint, etc. Or pressurized containers such as spray cans.
• Repairs should be carried out by a professional or qualified technician only. Incorrect repair could expose the user to potential electric shock or other kinds of hazards.
• Do not place the appliance in contact with water. The electrical insulation could be damaged and thus cause electric shock.
• Do not bend, tug, pull or compress the power cord to prevent damaging the power cord.

CAUTION

• Do not run the power cord under the carpet or cover the cord with throw rugs, runners, or similar covering. Arrange the cord away from high traffic area to prevent tripping over it.
• Only use this appliance as described in this manual.
• Do not obstruct the air inlet or outlet.
• Do not use abrasive solvents to clean this appliance.
• Proper adult supervision is required when using this appliance when there are children, persons with reduced physical, sensory, or mental capabilities, or pets present.
• Do not leave the appliance operating unattended.
• Do not touch any moving parts when the air conditioner is in operation.

Product Specification

Parts Details

Main Unit Components:

• Control Panel: Located on the top of the unit. (See Page 13 for details)
• Air Outlet: Vent for air discharge.
• Temperature Display: Shows current temperature or settings.
• Air Filter: Located behind the front grille. (See Page 23 for cleaning)
• Upper Drain Outlet: For continuous drainage during dry mode. (See Page 10 for connection)
• Air Exhaust: Port for connecting the exhaust hose. (See Page 10 for connection)
• Bottom Drain Outlet: For draining the water tank. (See Page 22 for details)
• Power Plug: Connects the unit to the power supply.
• Carrying Handle: For easier transport.

Note: The graphical representation might have slight differences than the actual product.

Included Accessories:

• Window Slider Kit (1x): Used to seal the opening in a window for the exhaust hose.
• Drain Hose (1x): Used for draining water.
• Exhaust Hose (1x): Used to vent hot air outside.
• Hose Connector (1x): Connects the exhaust hose to the unit and window kit.
• Window Kit Adapter (1x): Connects the exhaust hose to the window slider kit.

Installation Guide

Picking an Installation Location

• The air conditioner must be placed on a flat ground.
• Keep the air conditioner at least 50 cm or 19.7" away from any wall or obstacles.
• Do not place the air conditioner in a laundry room or near any open ignition sources such as open flames, gas appliances, or electric heaters.

Connecting the Exhaust Hose

Diagram illustrating the connection of the exhaust hose to the hose connector and window kit adapter.

Connect the exhaust hose to the hose connector and window kit adapter.

Extending the Window Slider Kit

Diagram showing the window slider kit components and how to adjust its length.

Adjust the length of the window slider kit according to your window, and then secure the position with the provided screws.

Attaching Exhaust Hose to the Unit

Diagram showing the exhaust hose being attached to the air exhaust port of the unit.

Slide the hose connector to the air exhaust on the unit, and attach the window kit adapter to the window slider kit.

Connecting Exhaust Hose to the Window

Vertical Window Setup:

Diagram showing the installation for a vertical window, including foam seal placement.

Horizontal Window Setup:

Diagram showing the installation for a horizontal window, including foam seal placement.

1. Attach foam seal to the window sash and the window frame.
2. Place the window slider kit between the window sash and window frame.

Exhaust Duct Placement

Diagram showing correct and incorrect exhaust duct configurations.

• Exhaust duct should be kept to a minimum length and as straight as possible.
• Stretching or bending the duct excessively will decrease cooling efficiency. (✔️ for straight, short duct; ❌ for bent, long duct)

Control Panel

The control panel features various icons and buttons for operating the air conditioner:

Remote Control

The remote control allows you to operate the air conditioner from a distance. It includes the following buttons:

• POWER: Power Button - Power ON / OFF the air conditioner (Page 16)
• MODE: Mode Button - Change the operation mode setting (Page 16, 17)
• SPEED: Speed Button - Control the fan speed (Page 16, 17)
• SWING: Swing Button - Enable the air outlet to oscillate (Page 17)
• TEMP/HRS +/-: Increase / Decrease Button - Adjust temperature / timer setting (Page 16-18)
• TIMER: Timer Button - Enable shut down / turn on timer (Page 18)
• SLEEP: Sleep Button - Enable sleep mode (Page 19)
• °C/°F: Unit Button - Changing display unit between °C and °F (Page 18)

Changing Remote Control Battery

Diagrams showing the process of replacing the remote control batteries.

1. Remove the back cover and insert 2 new AAA 1.5v batteries (not included).
2. Re-install the back cover to the remote control.

WARNING

• Do not use rechargeable batteries.
• Replace the old batteries with new ones of the same type.
• Do not dispose batteries as unsorted municipal waste.

Operation Instructions

Power ON / OFF

1. Press the ⏻ button on the control panel or press POWER on the remote control to turn on the unit.
2. Press the ⏻ button on the control panel or press POWER on the remote control again to turn off the unit.

Cool Mode

1. Press the [mode] button on the control panel or MODE on the remote control to select cool mode. The indicator will light up on the control panel.
2. Press the ▲ or ▼ buttons on the control panel or + or - on the remote control to adjust temperature setting. Temperature can be set from 16°C - 32°C / 61°F - 90°F.
3. Press the ? button on the control panel or SPEED on the remote control to adjust fan speed.

Dry Mode

1. Press the [mode] button on the control panel or MODE on the remote control to select dry mode. The indicator will light up on the control panel.

Fan Mode

1. Press the [mode] button on the control panel or MODE on the remote control to select fan mode. The indicator will light up on the control panel.
2. Press the ? button on the control panel or SPEED on the remote control to adjust fan speed.

Heat Mode

1. Press the [mode] button on the control panel or MODE on the remote control to select heat mode. The indicator will light up on the control panel.
2. Press the ▲ or ▼ buttons on the control panel or + or - on the remote control to adjust temperature setting. Temperature can be set from 61°F - 90°F.
3. Press the ? button on the control panel or SPEED on the remote control to adjust fan speed.

Oscillation Function

1. Press the ⟳ button on the control panel or SWING on the remote control to enable vent oscillation. The vents on the air conditioner will oscillate side to side.
2. Press the ⟳ button on the control panel or SWING on the remote control again to disable vent oscillation.

Turn ON Timer

1. Make sure the air conditioner is OFF.
2. Press the ⏱️ button on the control panel or TIMER on the remote control to begin setting the turn-on timer.
3. Press the ▲ or ▼ buttons on the control panel or + or - on the remote control to set the desired time.
4. Leave the setting for 5 seconds; the air conditioner will start the timer automatically.
5. Set the timer to 00 or manually turn ON the unit to cancel the timer setting.

Shut OFF Timer

1. Make sure the air conditioner is ON.
2. Press the ⏱️ button on the control panel or TIMER on the remote control to begin setting the shut-off timer.
3. Press the ▲ or ▼ buttons on the control panel or + or - on the remote control to set the desired time.
4. Leave the setting for 5 seconds; the air conditioner will start the timer automatically.
5. Set the timer to 00 or manually turn OFF the unit to cancel the timer setting.

Changing Temperature Unit

1. Press the [temp-unit] button (°C/°F) on the remote control to change the temperature unit between degrees Celsius and degrees Fahrenheit.

Sleep Mode

1. Press the ? button on the control panel or SLEEP on the remote control to enable sleep mode.
2. In cool mode, the air conditioner will increase temperature by 2°F after 1 hour, and then another 2°F after the 2nd hour. Then the air conditioner will keep the temperature constant for 10 hours.
3. In heat mode, the air conditioner will decrease temperature by 2°F after 1 hour, and then another 2°F after the 2nd hour. Then the air conditioner will keep the temperature constant for 10 hours.

Graphs illustrating temperature adjustments for Sleep + Cool Mode and Sleep + Heat Mode over time.

Automatic Defrost

At low room temperature, frost may build up at the evaporator during operation. The unit will automatically start defrosting and the power indicator will blink. The defrost control sequence is as follows:

• When the unit operates in cooling or drying mode, and the ambient temperature sensor detects the evaporator coil temperature is below 30°F, the compressor will stop operating for 10 minutes or until the coil temperature raises up to 44°F. After that, the unit will restart cool mode operation.
• When the unit operates in dry mode, once the coil temperature sensor detects the temperature of the evaporator is below 104°F and the differential temperature between coil temperature and room temperature is below 66°F after the compressor operation for 20 minutes, the unit starts defrosting for 5 minutes and the power indicator blinks.

Overload Protection

In the event of power loss, there is a 3-minute delay to protect the compressor before it restarts.

Grounding

This product must be properly grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock.

For additional safety, the power cord features an integrated circuit breaker. Test and reset the buttons provided on the plug.

Diagram of a power plug with TEST and RESET buttons.

The circuit breaker should be tested periodically by pressing the TEST button. If it does not cause the circuit breaker to trip or if the RESET button will not stay engaged, unplug the unit immediately and contact your service technician.

WARNING

• Improper connection can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded.
• Do not modify the plug provided with the product.

Water Drainage

Bottom Drain Outlet:

• When the internal water tank is full, the digital display will show "FL" error code.
• Carefully move the air conditioner to a drain location, then remove the bottom drain plug and drain the water.
• After draining, re-install the drain plug and restart the air conditioner.

Upper Drain Outlet:

• For continuous drainage during dry mode, remove the upper drain plug and insert a drain hose to the outlet.
• Place the other end of the hose to a drain area.

Attention: Do not submerge the end of the hose into water to prevent air lock.

Care and Maintenance

CAUTION

• Before cleaning the unit, you must shut down the machine and cut off the power supply.
• Never flush the air conditioner with water.

Clean the Unit

1. Clean the unit with a soft dry cloth or a damp cloth with neutral detergent.

NOTE:

• Do not flush the machine with water.
• Do not use volatile liquids such as thinner or alcohol to prevent damaging the unit.

Clean the Air Filter

Diagram showing the air filter being removed and cleaned.

1. Remove the air filters from the air conditioner.
2. Clean the air filters with a vacuum cleaner or with warm water with mild neutral detergent.
3. Make sure air filters are dry and then re-install them to the air conditioner.

Storage

If you will not be using the unit for an extended period of time, it is best to clean and dry out the unit completely.

1. Unplug the unit from the power outlet and detach the exhaust hose and window sliding kit from the unit.
2. Drain the remaining water from the unit.
3. Clean and dry the air filter.
4. Re-install the cleaned air filter at its position.
5. Store the unit in a dry indoor location. The unit must be kept in an upright position.

Attention: The evaporator of the unit must be dried out before storage to prevent molds by leaving the machine in a dry open area or turning on the machine with low speed fan mode.

Troubleshooting

Error Code

Disposal Guideline

This appliance contains refrigerant and other potentially hazardous materials. When disposing the appliance, follow all federal, state and local regulations. DO NOT dispose of this product as normal household waste or unsorted municipal waste.

When disposing this appliance, you have the following options:

• Dispose of this appliance at a designated municipal electronic waste collection facility.
• When buying a new appliance, the retailer will take the old appliance.
• The manufacturer may take back the old appliance.
• Sell the appliance to a certified scrap metal dealer.

Compliance Information

FCC Caution

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates users and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to a radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.

IC Warning

This device complies with Industry Canada's license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.