Official DS18 Pro Audio Store - Speakers, Subwoofers, Amps & More!
Owner's Manual for DS18 models including: GEN-X212LD, 1 12 SUBWOOFER
DS18 Loaded Enclosure Bass Package 2 x GEN-X124D 12" Subwoofers In a Ported Box 1800 Watts - Sky High Car Audio
DS18 GEN-X212LD Bass Package 2 x GEN-X124D 12" Subwoofers In a Ported
File Info : application/pdf, 6 Pages, 513.75KB
DocumentDocument12'' OWNER'S MANUAL GEN-X212LD 2x12''SUBWOOFER IN A PORTED BOX LOADED SUBWOOFER ENCLOSURE SPECIFICATIONS GEN-X212LD LOADED SUBWOOFER ENCLOSURE General Total Impedance . . . . . . . . . . . . . . . . . . . . . . 2 + 2 ohm (Individual Subwoofer Connector) Total RMS Power Handling . . . . . . . . . . . . . 900W Total MAX Power Handling . . . . . . . . . . . . . 1800W Sensitivity (1w/1m) . . . . . . . . . . . . . . . . . . . . 94dB Frequency Response . . . . . . . . . . . . . . . . . . . 29 - 250Hz Recommended Lo Pass Crossover. . . . . . . 120Hz Speaker Specifications 2 x 12" GEN-X124D Subwoofer Voice Coil Diameter . . . . . . . . . . . . . . . . . . . . 2" Voice Coil Former Material . . . . . . . . . . . . . Black Aluminum Winding Material . . . . . . . . . . . . . . . . . . . . . . SV Cone Material . . . . . . . . . . . . . . . . . . . . . . . . . Paper & Fiber Glass Dust Cap Material . . . . . . . . . . . . . . . . . . . . . . PPI Surround Material . . . . . . . . . . . . . . . . . . . . . . Foam Basket Material . . . . . . . . . . . . . . . . . . . . . . . . Steel Magnet Material . . . . . . . . . . . . . . . . . . . . . . . Ferrite Magnet Weight . . . . . . . . . . . . . . . . . . . . . . . . 70 Oz Box Specifications Internal Volume. . . . . . . . . . . . . . . . . . . . . . . . 90.6L Port Tune. . . . . . . . . . . . . . . . . . . . . . . . . Fb. . 35Hz Load Configuration . . . . . . . . . . . . . . . . . . . . Parallel Box Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Front Ported Box Material . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2" MDF Finish Material . . . . . . . . . . . . . . . . . . . . . . . . . Vinyl -3dB Dropping Point . . . . . . . . . . . . . . F3. . 29Hz Measurement Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.78" / 350mm Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38.58" / 980mm Depth 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11" / 280mm Depth 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14" / 356mm 1 DIMENSIONS GEN-X212LD 13.78" / 350mm 2 38.58" / 980mm 11.08" / 281.42mm 14.09" / 357.76mm 3 INSTALLATION INSTRUCTIONS Professional installation by an authorized DS18 dealer is highly recommended! Otherwise, the performance of your new gear may not be satisfactory. In the event that you decide to do your own installation, please read and follow this manual carefully. Failure to do so may compromise the integrity of this product, your automobile, and possibly void the product warranty. Use this Subwoofer Box with an external Monoblock subwoofer amplifier that can handle 1 ohm load impedance and a maximum of 900W RMS continuous power, otherwise the amplifier or the Subwoofer can get damaged. In case that you need to install an amplifier please refer to the amplifier's instruction manual to perform the installation of the amplifier before the use this Subwoofer Box. Do Not Connect this directly to the factory radio or aftermarket radio speaker output. This will not be enough power for the subwoofers and could be bad for the radio's amplifier if is not 1 ohm stable. Secure the subwoofer box with a strap or bracket to screw it down in case this box is loose on your trunk or a SUV cargo area to avoid this moving around which will damage the Subwoofer or box itself. In case of accelerating or hard braking this will reduce the possibility of movement! Major injuries may occur in case of an accident if this is not secured properly. If you already have installed the amplifier then follow these simple steps: 1 Connect the subwoofer box to the amplifier using a minimum 12Ga speaker wire and make sure the polarity (+) and (-) is correct, otherwise the sound will be affected. 2 You are now ready to play it for the first time. It is best to leave the gain all the way down in the beginning. Start with a low volume and work your way up. 3 Now you can tune the amp. We recommend using the Low Pass Filter at 120Hz or lower depending on your system. Take your time and make only one adjustment at a time. It may take some time to get the system fully adjusted. During this time the amp is drawing current from the battery. You should check the battery voltage from time to time and re-charge it if it gets low. That's it! You are done. Now have fun!! 4 FOR MORE INFORMATION PLEASE VISIT DS18.COM We LIKE IT LOUD