GE APPLIANCES AIR CONDITIONER

Model: APCA14YZBW

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

The image shown here is for illustrative purposes only and may be subject to change.
The actual descriptions of control panel and their locations may vary, depending on the model.
The remote control may vary depending on the model: The buttons on the remote control may have a different name or location than the remote control shown in this manual.

READ AND SAVE THESE INSTRUCTIONS

USING THE AIR CONDITIONER

Controls

The image shows the control panel and remote control. Specific button functions and locations may differ by model.

Cool Mode

Description of Cool Mode operation.

DRY Mode/Dehumidification

Description of Dry Mode operation.

FAN Mode

Description of Fan Mode operation.

HEAT Mode

Description of Heat Mode operation.

Power Outage Recovery Feature

Description of the Power Outage Recovery Feature.

CARE AND CLEANING

Air Filter

Instructions for cleaning the air filter.

WARNING: Ensure the unit is unplugged before cleaning.

Description of filter cleaning process and image showing filter removal.

Cleaning the Unit

Instructions for cleaning the exterior and interior of the air conditioner.

How to Drain the Remote Water (If Applicable) Service Control

Instructions on how to drain excess water.

INSTALLATION INSTRUCTIONS

BEFORE YOU BEGIN

IMPORTANT: Read all instructions before installation.

Location Requirements

Place the air conditioner on a flat, level surface at least 30" (76.2 cm) from any wall.
Maintain a minimum 30" (76.2 cm) clearance around the air conditioner to ensure proper airflow.
Keep the air conditioner free of obstructions like drapes or curtains.
The exhaust hose should be free of obstructions.
Do not place the air conditioner on an unstable surface.
Do not place the air conditioner in direct sunlight or near a heat source.
The window panel can be installed in a window with a minimum 20" (55.88 cm) to a maximum 46" (121.92 cm) opening.

PARTS INCLUDED (Appearance may vary)

1. Control Panel
2. Louver
3. Exhaust Hose
4. Casters
5. Handle
6. Grill
7. Power Cord
8. Filter
9. Air Outlet
10. Water Outlet
11. Window sealing plate assembly

1. UNPACK AIR CONDITIONER

WARNING: Excessive Weight Hazard. Use two or more people to move and install the air conditioner.

Remove packaging materials. Save the carton and foam for storage.
Handle the air conditioner gently and keep it upright.

2. Install Exhaust Hose Assembly to Back of Unit

Twist the round adapter counterclockwise into the exhaust port on the back of the Air Conditioner.

3. INSTALL WINDOW PANELS

Measure the window opening. Use the middle panel for a 20" opening. Add side panels for larger openings (up to 46").
Place the Window Kit into the window opening, ensuring Cam Locks are accessible. Slide side panels outward to fill the opening and lock with Cam Locks.
Apply foam seals for a better seal. Slide the window shut against the Window Kit.

4. Connect Exhaust Hose to the Window Panel

Place the Air Conditioner near the window. Extend the hose to the Window Kit. Insert the Exhaust Hose Adapter into the Window Kit opening and slide it into the locking position. Ensure the hose runs straight and is not overextended. The Air Conditioner must be vented to the outside. Do not use a longer hose than provided.

Diagrams showing vertical and horizontal window installations.

5. COMPLETE INSTALLATION

WARNING: Electrical Shock Hazard. Plug into a grounded 3 prong outlet. Do not remove the ground prong or use an adapter/extension cord.

Plug the power cord into a grounded 3 prong outlet.
Press the Reset button on the plug to ensure the safety plug is working.
Allow 20" clearance around the Air Conditioner for proper air circulation.
When removing the Air Conditioner, remove the Window Kit.

ELECTRICAL REQUIREMENTS

Description of electrical requirements.

TROUBLESHOOTING TIPS

Problem	Possible Causes	Solution
Unit does not start or operate	Power supply cord is not plugged into an outlet.	Plug the power cord into a grounded 3 prong outlet.
	Power supply cord has tripped.	Press and release the RESET button on the power supply cord.
	The Power button has not been pressed.	Press the Power button on the Control Panel or Remote Control to turn ON the air conditioner.
	There is no power to the electrical outlet.	Plug a working lamp into the outlet to check for power.
	A household fuse has blown or a circuit breaker has tripped.	Replace the fuse or reset the circuit breaker.
	The control was programmed for a Time Delay.	Cancel the Time Delay. See "Control Panel."
Remote control is not working	Batteries are dead.	Replace the batteries.
	Batteries are installed incorrectly.	Make sure the batteries are inserted in the correct position.
Air conditioner is working but the room is not cooling.	The room temperature is hot.	Allow time for the room to cool when you first turn on the unit. Make sure the air conditioner has an adequate BTU rating for the room size.
	The control is set incorrectly to Fan or DRY mode.	Set the Mode to Cool and the Fan Speed to High.
	Airflow is restricted.	Remove any obstacles to airflow and redirect airflow for uniform cooling.
	Temperature set too high.	Lower the set temperature.
	Air filters are dirty or restricted.	Clean the air filter. See "Air Conditioner Care."
	Air conditioner installed incorrectly	Check the exhaust hose and window panel for proper installation.
	Doors and windows are open.	Close the doors and windows to the room being cooled.

Error Codes

WIFI SETUP (on some models)

GE Appliances WiFi Connect (for customers in the United States)

Your Air Conditioner (AC) may have a Connected Appliance Information label. This indicates it is GE Appliances U+ Connect Enabled, allowing communication with your smartphone for remote monitoring and control.

Visit GEAppliances.com/connect to learn more about connected appliance features.

How it Works:

Download the GE Appliances app from iTunes or Google Play. Once connected, use the app to control your air conditioner remotely.

Questions about U+ Connect:

Visit products.geappliances.com/appliance/gea-support-search-content for support articles.

REFURBISHED PRODUCT LIMITED THIRTY DAY WARRANTY

This warranty covers electronic or mechanical defects for THIRTY DAYS from the original purchase date. It does not cover cosmetic issues. GE Appliances will repair or replace defective units/parts with new or rebuilt materials at no charge.

This warranty does not cover installation, damage from misuse, or products that have been altered.

Warranty Repair Information:

For service during the warranty period, visit www.ConsumerServiceRefurbish.com or call 562-946-3531 to obtain a claim number. Pack the unit securely with a copy of your purchase receipt and send it freight prepaid and insured to:

Refurbished Product Service Center
Att: Customer Service Department
13225 Marquardt Avenue
Santa Fe Springs, CA 90670

Owner's Information:

NAME: [Owner's Name]
ADDRESS: [Owner's Address]
CITY: [City]
STATE: [State]
ZIP CODE: [Zip Code]
PHONE: [Phone Number]
E-MAIL: [Email Address]
MODEL: APCA14YZBW
SERIAL NO.: [Serial Number]

REGULATORY INFORMATION

FCC/IC Compliance Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. If this equipment causes harmful interference, try to correct it by reorienting the antenna, increasing separation, connecting to a different outlet, or consulting a technician.

Labelling: Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.

*Select Models Only: This product has WiFi capability and requires Internet connectivity and a wireless router.

Use of the Works with Apple HomeKit™ logo means the accessory is designed to connect to iPod touch®, iPhone®, or iPad® and meets Apple® performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.