Vehicle adaptation solutions | BraunAbility Europe
User Manual for BraunAbility models including: SAS, SA, SAL, High Viz HVSA, HVLSA, SAS Solo Floor Anchor, SAS, Solo Floor Anchor, Floor Anchor, Anchor
User manuals | BraunAbility Europe
File Info : application/pdf, 14 Pages, 692.07KB
DocumentDocumentSolo floor anchor Single anchoring points for dedicated wheelchair spaces Solo floor anchor SAS SA SAL Solo floor anchor High Viz HVSA HVLSA EN Installation and user manual EN 4 Solo floor anchor Thank you for choosing a Solo floor anchor from BraunAbility! The following manual is an important part of the product, providing you with information on how to achieve maximum performance and safe operation. Keep the manual in a safe place so that you can refer to it when necessary. If you have any questions about your adaptation, please contact your installation engineer. If you want to know more about us and our range of car adaptation solutions visit www.braunability.eu. Once again, thank you for placing your confidence in our products! 5 Solo floor anchor EN Index Safety Installation Operation Care instructions 6 General guidance 7 Installation planning 8 Drilling 9 Orientation 10 Fit and use 11 Maintenance 6 Solo floor anchor Safety General guidance 1 It is recommended that Solo floor anchors are installed by an experienced technician/vehicle converter. 2 Do not make any alterations to the Solo floor anchors. 3 Do not install the floor anchors to unsound metal, wood, or plastic structures without additional and suitable reinforcement. 4 Solo floor anchors meet the requirements of ISO 10542 & SAE J2249. Testing was conducted to the same configuration to that recommended by this guide, any deviation from the recommendation is the responsibility of the installer. Solo static anchor Spreader plate Spring washer M24 nut Solo floor anchor 90 mm (SAL) Installation Installation planning 1 Position the wheelchair facing forward, centrally in the designated region of the vehicle. 2 Allow a clear zone of at least 450 mm behind, and 650 mm in front of the head of the wheelchair user (Figure 1). When positioning the wheelchair, take the location of the shoulder belt anchorage into account. 3 Mark out the chosen floor anchor points, guidance positions are shown in Figure 2, and check under the vehicle if there are no brake lines, fuel tanks, or chassis parts blocking the installation. 450 mm 650 mm 7 Solo floor anchor EN 220 220 Installation Seated head hight Figure 1. Clear head and chest zones. 35°-45° 300-400 mm 330-500 mm 1100-1370 mm Figure 2. Floor anchor placement. 8 Solo floor anchor Installation Drilling 4 Drill a 25 mm hole through all layers of the car floor and counterbore the hole to 32 mm with a depth of 8 mm (Figure 3). 32 mm 25 mm Figure 3. Counterbore a hole. 8 mm 5 Mount the floor anchor throught the layers as shown in Figure 4. If you need to modify the spreader plate to clear an obstruction, always leave at least 15 mm around the bolt hole. It may be necessary to provide fillers between the vehicle floor convolutions to prevent these from being crushed when the nuts are tightened. Vehicle floor Flooring Figure 4. Mount the floor anchor. Installation Orientation 6 It is essential that the slot in each floor anchor is orientated as shown in Figure 5. Tighten to 30 Nm from underneath using the nut, washer and spreader plate. 9 Solo floor anchor EN Installation Figure 5. Floor anchor orientation. 10 Solo floor anchor Operation Fit and use 1 Attach a tie-down onto the floor anchor by aligning the protrusion within the cleat, to the slot on the floor anchor (Figure 6). Slide the cleat fully home. 2 Rotate the cleat 90 degrees, clockwise or counterclock wise, to secure (Figure 7). 3 To remove the cleat from the floor anchors, turn the cleat to align the raised protrusion on the cleat with the indent on the floor anchor and slide off. Cleat Figure 6. Slide on the floor anchor. Figure 7. Turn 90 degrees. Care instructions Maintenance Solo floor anchors are made from stainless steel and therefore only require a periodic brush to remove debris from the slot and mating surfaces. 11 Solo floor anchor EN Care instructions ISO 9001:2015 C E R T I F I C AT I O N TM BraunAbility Safety Centre Accreddited test labatory www.braunability.eu BraunAbility Europe AB is certified in accordance with ISO 9001:2015 and ISO 14001:2015 Illustrations, descriptions and specifications in the user manual are based on current product information. BraunAbility Europe AB reserves the right to make alterations without previous notice. © 2024 BraunAbility Europe AB BraunAbility Europe AB Åkerivägen 7 443 61 Stenkullen Sweden Phone: +46 302 254 00 E-mail: info@braunability.eu www.braunability.eu 427971-1 2024/10