Single-door Access Controller (Card/Password)
User Instruction
Model: AD2000-M
Category: RFID ACCESS CONTROL
Special attention: 1. Please follow the instructions strictly while using it. 2. Please read this instruction carefully before you use the system and follow the instructions strictly while using it.
1. Performance Parameters
| Item Name | Parameters |
|---|---|
| Working power | DC12V±20% 100MA |
| Relay performance | 2A |
| Card capacity | 800PCS |
| Valid password | General 1 set |
| RF card-types | EMID card or ID compatible card |
| Card reading distance | 3-15CM |
| Signal interface | Relay signal |
| DOB interface | 1 |
| Door bell interface | 1 |
2. Operating List
| Function settings | 1st Step | 2nd Step | 3rd Step | 4th Step | 5th Step |
|---|---|---|---|---|---|
| Modify programming code | Press "0" | Press "[*]" | Input password and press "[#]" | Input password again and press "[#]" | [ESC] |
| Add user card | Press "1" | Read new card | Press "[#]" | Press "[#]" | |
| Delete user card | Press "2" | Card and input the | Press "[#]" | ||
| Modify relay-working time | Press "3" | Input two numbers (01-99) in seconds unit | Press "[#]" | ||
| Modify general code | Press "4" | Input password and press "[#]" | Input password again and press "[#]" | ||
| Modify work pattern | Press "5" | 1. Only card to open the door pl spree "1" 2. Card and code to open the door pls press "2" 3. Card or code to open the door pls press "3" |
Press "[#]" |
Programming default password: 1688
General opening the door password: 8888
Forcibly recover factory programming password: "RESET" short circuit.
Make managing card: power off and "RESET" short circuit, read the 1st. card to be "adding card" and the 2nd. One to be "deleting card".
Notes: The password can be 10 numbers at most, the card number inputted is the former10 ABA number.
How to add card by managing card: Read "Adding card" and read cards you want to add, then read "adding card" again and finished.
3. Wiring Diagram
The following describes the wiring connections for the access controller.
Common Power Supply Wiring:
Connections:
- [Power] O OK: Indicates power status.
- Keypad: 1, 2, 3, 4, 5, 6, 7, 8, 9, [*], 0, [#]
- [Bell] Button
- [RFID Access Control] Unit
- Wiring diagram of common power supply:
- Unit's [DC+12V] connects to [Power Supply Port]
- Unit's [GND] connects to [Electric Lock Port]
- Unit's [COM] connects to the lock's [PUSH] terminal
- Unit's [PUSH] connects to the lock's [Switch Port]
- Unit's [OPEN SW+] connects to a [Switch Port] (e.g., door sensor input)
- Unit's [OPEN SW-] connects to another [Switch Port] (e.g., door sensor input)
- Unit's [DOOR BELL] connects to the [Door Bell Port]
Note on Common Power Supply:
"NO" means Normally Open: Connect to an electric lock that opens when power is applied.
"NC" means Normally Closed: Connect to an electric lock that opens when power is removed.
The maximum working current of the relay is 2A.
Dedicated Power Supply Wiring:
Connections:
- [Power] O OK: Indicates power status.
- Keypad: 1, 2, 3, 4, 5, 6, 7, 8, 9, [*], 0, [#]
- [Bell] Button
- [RFID Access Control] Unit
- Wiring diagram for dedicated power supply:
- Unit's [DC+12V] connects to external [DC+12V]
- Unit's [GND] connects to external [GND]
- Unit's [COM] connects to the lock's common terminal ([PUSH+])
- Unit's [PUSH] connects to the lock's [NO] terminal (for Normally Open locks)
- Unit's [OPEN SW+] connects to a [switch port] (e.g., door sensor input)
- Unit's [OPEN SW-] connects to another [NC] terminal (e.g., door sensor input)
- Unit's [DOOR BELL] connects to the [door bell port]
External Lock Terminals:
[Port of electric lock that can be open when power on] (This is the NO terminal)
[Port of electric lock that can be open when power off] (This is the NC terminal)
Note on PUSH Output:
If 'COM' and 'GND' are connected internally, 'PUSH' output is low level; If 'COM' and '+12V' are connected internally, 'PUSH' output is high level. 'COM' is the common port of the relay.
